Fax Settings (iR 1133iF Only)

NOTE
About the menu options in the following chart
Default settings are highlighted in bold.
The settings marked with "*A" cannot be imported or exported via the Remote UI.
For settings or values with "*1" mark, the setting or value may be unavailable or vary depending on the country where you are using the machine.

Basic Settings


Settings
Descriptions
Register Unit Telephone Number
You can register the fax number of the machine.
"Register Unit Telephone Number"
See the Getting Started.
Select Line Type*1

Select a line type.
Pulse, Tone
"Select Line Type"
Off-Hook Alarm

Specify whether to sound an alarm when the telephone handset is left unhooked and adjust the volume.
Off
On:
Off-Hook Alarm Volume: 1 to 3
"Off-Hook Alarm"

TX Function Settings


Settings
Descriptions
Change Defaults

You can register scan settings for documents.
"Change Defaults"
Register Unit Name (Fax)
Register your name or company's name (sender's name).
"Register Unit Name (Fax)"
See the Getting Started.
ECM TX

You can specify whether to use ECM.
Off, On
"ECM TX"
Pause Time

You can specify the number of seconds for the pause time.
1 to 4*1 to 15*1 (seconds)
"Pause Time"
Auto Redial

You can specify whether to redial when fax documents cannot be sent.
Off, On*1
"Auto Redial"
Redial Times

You can specify the number of times to redial.
1 to 2 to 10 (times)
"Auto Redial"
Redial Interval

You can specify the interval between redials.
2*1 to 99 (minutes)
"Auto Redial"
Redial When Err Occurs
You can specify whether to redial when a send error occurs.
Off, On
"Auto Redial"
Sender ID
The sender ID is printed at the top of each page that you are sending, along with the fax number and sender's name. This helps the recipient to identify the sender.
Off, On
"Sender ID"
Print Location
Select the location where the Sender ID is printed.
On Image, Above Image
"Sender ID"
Mark No. as: TEL/FAX
Select the text to add in front of the number.
FAX, TEL
"Sender ID"
Check Dial Tone Before Sending
You can specify whether to dial after checking the dial tone when sending fax documents.
Off*1, On
"Check Dial Tone Before Sending"

RX Function Settings


Settings
Descriptions
ECM RX

You can specify whether to use ECM.
Off, On
"ECM RX"
Incoming Ring
Set whether or not to ring the external telephone when <RX Mode> is set to <Auto> or <Fax/Tel Auto Switch>.
Off
On:
Ring Times: 1 to 2 to 99*1 (times)
"Incoming Ring"
Remote RX

You can specify whether to use the "remote receiving function" enabling you to receive fax documents by dialing an ID number even in the middle of a telephone call.
Off
On*1:
Remote RX ID: 00 to 25 to 99
"Remote RX"
Auto RX Switch
Set the incoming call ring time before the machine switches to the fax mode automatically. This option can be enabled when the <RX Mode> is set to <Manual>.
Off
On:
Incoming Ring Time: 1 to 15 to 99 (seconds)
"Auto RX Switch"

RX Print Settings


Settings
Descriptions
2-Sided Printing
Enable this option to print on both sides of paper. This saves excessive paper consumption.
Off, On
"2-Sided Printing"
Reduce RX Size

You can reduce the size of received documents and print them.
Off
On:
Ratio: Auto, 97, 95, 90, 75 (%)
Direction: Vertical/Horizontal, Vertical Only
"Reduce RX Size"
RX Page Footer
You can specify whether to print information such as reception date when printing received documents.
Off, On
"RX Page Footer"
Continue Printing When Toner Is Low
Specify whether to continue printing received documents when the toner is nearly empty.
Off, On
"Continue Printing When Toner Is Low"

Fax Setup Guide*A

Specify initial fax settings and connect the telephone cable.
See the Getting Started.
0F27-0K3