Attention (Printer Installation)

Before installing the printer, see "Important Safety Instructions."

IMPORTANT
Protecting the printer from condensation To prevent condensation from forming inside the printer in the following cases, adjust the printer to the ambient temperature and humidity for at least two hours before use. When the room where the printer is installed is heated rapidly When the printer is moved from a cool or dry location to a hot or humid location If water droplets (condensation) form inside the printer, this can result in paper jams or poor print quality. Precautions for the power supply Use an AC power outlet exclusively for the printer. Do not use the other sockets of the AC power outlet. Do not plug the power plug in the auxiliary outlet on a computer. Do not use the same AC power outlet for both the printer and any of the following equipment. Copy machine Air conditioner Shredder Equipment that consumes a large amount of electricity Equipment that generates electrical noise The maximum power consumption of the printer is 1,420 W or less. Electrical noise or a dramatic drop in mains voltage may cause the printer or computer to operate incorrectly or lose data. If you have any questions regarding your power supply, contact your power company or your nearest electronics store. Do not install the printer in the following locations, as this may result in damage to the printer. A location subject to dramatic changes in temperature or humidity A location subject to condensation A poorly ventilated location (If you use the printer for a long time or to perform a large amount of printing in a poorly ventilated room, the ozone or other odors generated by the printer may create an uncomfortable working environment. In addition, chemical particles are dispersed during printing. Therefore, it is important to provide adequate ventilation. Also avoid locations where people would be exposed to emissions from the machine). A location near equipment that generates magnetic or electromagnetic waves A laboratory or location where chemical reactions occur A location exposed to salt air, corrosive gases, or toxic gases A location, such as on a carpet or mat, that may warp from the weight of the printer or where the printer is liable to sink Precautions when preparing the toner cartridge See "Attention (Toner Cartridge)." Precautions when connecting the power cord Do not plug the power plug of the printer into an auxiliary outlet on a computer. One AC power outlet should be used exclusively for the printer. Do not connect this printer to an uninterruptible power source. This may cause printer malfunction or breakdown in the event of a power failure. When turning ON the printer for the first time after the printer installation Before turning ON the printer, be sure to insert the paper drawer in the printer. Although a sheet of blank paper may be output, this is not an error. Precautions when installing the paper feeder Do not touch the connector (A) on the paper feeder. This may result in damage to the printer or misfeeds. If you cannot place the printer on the paper feeder properly, lift the printer once, hold it horizontally, and place it again. If you try to place the printer forcefully without lifting it, the connector and positioning pins may be broken. Be sure to turn the printer ON once when loading paper in the paper drawer for the first time after installing the paper feeder. Precautions when installing/removing ROM Be sure not to touch the switches on the main board. If you change the switches, the printer does not operate properly. Observe the following precautions when handling ROM to prevent damage from static electricity. Touch a metal object to dissipate static electricity before handling them. When handling ROM, do not touch anything that generates static electricity such as the computer display. Do not touch the main board parts, printed wire, or connectors with your hands. Take ROM out of the protective bag right before it is installed. When installing ROM, be careful so that any metal objects such as screws do not touch the main board. Do not directly touch parts on the main board, the printed circuits, or the connectors with your hands. If any of screws, clips, staples, and so on should drop inside the printer, do not plug the power plug in the AC power outlet and contact your local authorized Canon dealer. Do not turn the printer ON without the slot cover attached. This may result in damage to the printer.

IMPORTANT

Protecting the printer from condensation

To prevent condensation from forming inside the printer in the following cases, adjust the printer to the ambient temperature and humidity for at least two hours before use.

When the room where the printer is installed is heated rapidly

When the printer is moved from a cool or dry location to a hot or humid location

If water droplets (condensation) form inside the printer, this can result in paper jams or poor print quality.

Precautions for the power supply

Use an AC power outlet exclusively for the printer. Do not use the other sockets of the AC power outlet.

Do not plug the power plug in the auxiliary outlet on a computer.

Do not use the same AC power outlet for both the printer and any of the following equipment.

Copy machine

Air conditioner

Shredder

Equipment that consumes a large amount of electricity

Equipment that generates electrical noise

The maximum power consumption of the printer is 1,420 W or less.

Electrical noise or a dramatic drop in mains voltage may cause the printer or computer to operate incorrectly or lose data.

If you have any questions regarding your power supply, contact your power company or your nearest electronics store.

Do not install the printer in the following locations, as this may result in damage to the printer.

A location subject to dramatic changes in temperature or humidity

A location subject to condensation

A poorly ventilated location
(If you use the printer for a long time or to perform a large amount of printing in a poorly ventilated room, the ozone or other odors generated by the printer may create an uncomfortable working environment. In addition, chemical particles are dispersed during printing. Therefore, it is important to provide adequate ventilation. Also avoid locations where people would be exposed to emissions from the machine).

A location near equipment that generates magnetic or electromagnetic waves

A laboratory or location where chemical reactions occur

A location exposed to salt air, corrosive gases, or toxic gases

A location, such as on a carpet or mat, that may warp from the weight of the printer or where the printer is liable to sink

Precautions when preparing the toner cartridge

See "Attention (Toner Cartridge)."

Precautions when connecting the power cord

Do not plug the power plug of the printer into an auxiliary outlet on a computer.

One AC power outlet should be used exclusively for the printer.

Do not connect this printer to an uninterruptible power source.
This may cause printer malfunction or breakdown in the event of a power failure.

When turning ON the printer for the first time after the printer installation

Before turning ON the printer, be sure to insert the paper drawer in the printer.

Although a sheet of blank paper may be output, this is not an error.

Precautions when installing the paper feeder

Do not touch the connector (A) on the paper feeder. This may result in damage to the printer or misfeeds.

If you cannot place the printer on the paper feeder properly, lift the printer once, hold it horizontally, and place it again.
If you try to place the printer forcefully without lifting it, the connector and positioning pins may be broken.

Be sure to turn the printer ON once when loading paper in the paper drawer for the first time after installing the paper feeder.

Precautions when installing/removing ROM

Be sure not to touch the switches on the main board. If you change the switches, the printer does not operate properly.

Observe the following precautions when handling ROM to prevent damage from static electricity.

Touch a metal object to dissipate static electricity before handling them.

When handling ROM, do not touch anything that generates static electricity such as the computer display.

Do not touch the main board parts, printed wire, or connectors with your hands.

Take ROM out of the protective bag right before it is installed.

When installing ROM, be careful so that any metal objects such as screws do not touch the main board.

Do not directly touch parts on the main board, the printed circuits, or the connectors with your hands.

If any of screws, clips, staples, and so on should drop inside the printer, do not plug the power plug in the AC power outlet and contact your local authorized Canon dealer.

Do not turn the printer ON without the slot cover attached. This may result in damage to the printer.

NOTE

About the toner cartridge included with this printer

The average yield of the included toner cartridges is as follows.

Average yield of K (Black) toner cartridge: 7,000 pages*1

Average yield of Composite C (Cyan), M (Magenta), and Y (Yellow) toner cartridges: 7,400 pages*1

		*1	The average yield is on the basis of "ISO/IEC 19798"* when printing A4 size paper with the default print density setting.
		*	"ISO/IEC 19798" is the global standard related to "Method for the determination of toner cartridge yield for color printers and multi-function devices that contain printer components" issued by ISO (International Organization for Standardization).

For purchasing replacement toner cartridges, see "Consumables."