Inner Finisher-K

Install "Inner Finisher-K" to use the following finish functions.

Offset
Each printout group is shifted in alternating layers.

Staple + Collate
The printouts are collated into sets arranged in page order and stapled (Corner/Double).

Staple + Group
All printouts of the same original page are grouped together into sets and stapled (Corner/Double).

Staple Free
The printouts are crimped and bound without using a staple. You can easily split the paper by pressing the crimped part with your fingers. This function is useful for saving staples and also binding printouts briefly.


For information on the paper sizes that can be used for Staple Free, see Specifications. Depending on the usage environment and paper type, the crimped part may be split easily.

Manual Stapling
You can manually staple printed paper by inserting paper in the slit. As an example of use, you can remove staples bound to the document, copy or scan it, and then staple the document again.

External View

Auxiliary Tray

Pull out the auxiliary tray if you are outputting large size paper.

Output Tray

Paper is output to the output tray.

Staple Button

Press this button when you manually staple paper (Manual Stapling). You can also staple paper without pressing the button. You can specify the time period for the paper to be stapled after inserting the paper. <Adjust Action>

Slit

Insert paper to manually staple the paper. You can specify the time period for the paper to be stapled after inserting the paper.

Front cover

Open to remove jammed paper, clear a staple jam in the stapler unit, or replace the staple cartridge.

Manual Stapling

Place the desired bundle of paper into the slit in the inner finisher.

Insert the corner of the paper bundle where you want it stapled straight into the slit, with the front side of the paper facing down.

When the paper bundle is sensed, the staple button starts to blink and automatic stapling is performed.

You can set the time in seconds to elapse before stapling is executed. <Time Until Stapling Starts>

You can perform stapling without waiting for the specified stapling start time to come. While holding the paper bundle with one of your hands, use the other hand to press the staple button.

Pull out the paper bundle.

Wait for the staple button to turn off, and then pull out the paper bundle.


You cannot perform manual stapling while outputting of printed paper continues.


To output paper to the upper tray with "Inner Finisher-K" installed requires "3 Way Unit-D." For information on the paper sizes that can be used for Staple, see Specifications. To replace the staple cartridge of the staples, see Replenishing the Staples (Optional). For how to clear a paper jam or a staple jam, see Clearing Paper Jams and Clearing Staple Jams (Optional). The maximum number of bindable sheets may not be possible, depending on the paper type. In this case, change the paper type, or reduce the number of sheets to bind. Collate and group If you select <Offset> in combination with the collate or group function, each printout group is shifted. Staplers When you are using the Staple mode, do not remove the stack of paper from the output tray during the job. Remove the stack of paper when the job has been completed. If the <Load staples into the stapler unit.> message appears, almost all of the staples have been used. To proceed, replace the staple cartridge. Output temporarily stops when the tray reaches the lowest position or when 30 sets have been stapled. Printing resumes when you remove all of the paper that has been output.

To output paper to the upper tray with "Inner Finisher-K" installed requires "3 Way Unit-D."

For information on the paper sizes that can be used for Staple, see Specifications.

To replace the staple cartridge of the staples, see Replenishing the Staples (Optional).

For how to clear a paper jam or a staple jam, see Clearing Paper Jams and Clearing Staple Jams (Optional).

The maximum number of bindable sheets may not be possible, depending on the paper type. In this case, change the paper type, or reduce the number of sheets to bind.

Collate and group

If you select <Offset> in combination with the collate or group function, each printout group is shifted.

Staplers

When you are using the Staple mode, do not remove the stack of paper from the output tray during the job. Remove the stack of paper when the job has been completed.

If the <Load staples into the stapler unit.> message appears, almost all of the staples have been used. To proceed, replace the staple cartridge.

Output temporarily stops when the tray reaches the lowest position or when 30 sets have been stapled. Printing resumes when you remove all of the paper that has been output.