<Adjust Action>
This section describes the copy and print finishing settings, such as adjusting the saddle stitch position.
<Saddle Stitch Staple Repositioning>![](./images/global_images/1T0002134966/g_ne_toggle_open.gif)
![](./images/book_images/b_key_Add.gif)
(Settings/Registration)
![](./images/book_images/b_in_arrow_right.gif)
<Adjustment/Maintenance>
![](./images/book_images/b_in_arrow_right.gif)
<Adjust Action>
Feeds papers to the saddle stitcher unit and staples them several times, and performs the saddle stitch staple repositioning procedure. The machine performs this adjustment procedure if stapling has not been performed after you clear a staple jam or replace the staple cartridge.
|
Make sure to remove all output booklets from the booklet tray before performing the saddle stitch staple repositioning procedure. Make sure to remove the paper that was used for adjustment. |
|
Paper that is required for the saddle stitch staple repositioning procedure is automatically fed to the saddle stitcher unit by the machine. 305 mm x 457 mm, A3, B4, A4R, 11" x 17", LGL, LTRR, or custom paper sizes equivalent to these paper sizes can be used. (Make the paper source to which transparencies are registered unavailable.) This mode can be set when the Booklet Finisher-W PRO or Booklet Finisher-V is attached. |
<Change Fold/Stitch Position>
![](./images/book_images/b_key_Add.gif)
(Settings/Registration)
![](./images/book_images/b_in_arrow_right.gif)
<Adjustment/Maintenance>
![](./images/book_images/b_in_arrow_right.gif)
<Adjust Action>
If you notice that the saddle stitch position of the paper is not exactly in the middle of the booklet, you can make adjustments to the saddle stitch position to compensate for this error. Adjust the folding position of the paper and the saddle stitch position at the same time.
Adjusting the Saddle Stitch Position<Adjust Saddle Stitch Fold Position>
![](./images/book_images/b_key_Add.gif)
(Settings/Registration)
![](./images/book_images/b_in_arrow_right.gif)
<Adjustment/Maintenance>
![](./images/book_images/b_in_arrow_right.gif)
<Adjust Action>
If you notice that the folds of the paper are not exactly in the middle of the booklet, you can make adjustments to the fold placement to compensate for this error. This mode enables you to adjust the folding position without changing the stapling position.
Adjusting the Saddle Stitch Folding Position<Adjust Double Staple Width>![](./images/global_images/1T0002134966/g_ne_toggle_open.gif)
![](./images/book_images/b_key_Add.gif)
(Settings/Registration)
![](./images/book_images/b_in_arrow_right.gif)
<Adjustment/Maintenance>
![](./images/book_images/b_in_arrow_right.gif)
<Adjust Action>
You can adjust the double staple width.
|
When the paper width is smaller than 257 mm, double staple width is fixed <120 mm>. This mode can be set when the Staple Finisher-W PRO, Booklet Finisher-W PRO, Staple Finisher-X, or Booklet Finisher-X is attached. When the Staple Finisher-W PRO or Booklet Finisher-W PRO is attached: valid only when the Offset mode is not set. The mode is set to <120 mm> when used with the Offset mode. When the Staple Finisher-X or Booklet Finisher-X is attached: the productivity of the machine may be slightly reduced if this mode is set to <120 mm>. |
<Switch Finisher Puncher Mode>![](./images/global_images/1T0002134966/g_ne_toggle_open.gif)
![](./images/book_images/b_key_Add.gif)
(Settings/Registration)
![](./images/book_images/b_in_arrow_right.gif)
<Adjustment/Maintenance>
![](./images/book_images/b_in_arrow_right.gif)
<Adjust Action>
You can set whether to give priority to the punching speed or to precision.
|
This mode can be set when the puncher unit is attached to the Staple Finisher-X, Booklet Finisher-X, Staple Finisher-V or Booklet Finisher-V. |
<Speed/Precision Priority for Double Staple>![](./images/global_images/1T0002134966/g_ne_toggle_open.gif)
![](./images/book_images/b_key_Add.gif)
(Settings/Registration)
![](./images/book_images/b_in_arrow_right.gif)
<Adjustment/Maintenance>
![](./images/book_images/b_in_arrow_right.gif)
<Adjust Action>
You can set whether to give priority to the double stapling speed or to precision.
|
This mode is enabled only when using the following paper: Paper size: The width for the feeding direction is 215.9 mm or less Paper type: Plain, Heavy 1, Color, Pre-punched Paper weight: 64 g/m2 to 128 g/m2 If you select <Speed Priority>, stapled output paper may not be aligned due to the temperature, humidity, or characteristics of the paper type. |
|
This mode can be set when the Staple Finisher-W PRO or Booklet Finisher-W PRO is attached. |
<Adjust Trim Width>![](./images/global_images/1T0002134966/g_ne_toggle_open.gif)
![](./images/book_images/b_key_Add.gif)
(Settings/Registration)
![](./images/book_images/b_in_arrow_right.gif)
<Adjustment/Maintenance>
![](./images/book_images/b_in_arrow_right.gif)
<Adjust Action>
You can adjust the trimming width of Saddle Stitch printouts in 0.1 mm increments. When using the optional Booklet Trimmer-F, also see the included instruction manual for more information.
|
This mode can be set in the following cases: When the Inner Booklet Trimmer-A is attached to the Booklet Finisher-X When the Booklet Trimmer-F is attached to the Booklet Finisher-W PRO
|
<Adjust Fold Position>
![](./images/book_images/b_key_Add.gif)
(Settings/Registration)
![](./images/book_images/b_in_arrow_right.gif)
<Adjustment/Maintenance>
![](./images/book_images/b_in_arrow_right.gif)
<Adjust Action>
You can adjust the paper folding position.
Adjusting the Paper Folding Position<Alignment Adjustment When Stapling>![](./images/global_images/1T0002134966/g_ne_toggle_open.gif)
![](./images/book_images/b_key_Add.gif)
(Settings/Registration)
![](./images/book_images/b_in_arrow_right.gif)
<Adjustment/Maintenance>
![](./images/book_images/b_in_arrow_right.gif)
<Adjust Action>
The copied or printed paper may shrink because of temperature, humidity, or a characteristic of the paper type. In this case, this mode enables you to align copied or printed papers by adjusting the position of the alignment guide inside the finisher so as to staple the aligned papers.
|
This mode can be set when the Staple Finisher-W PRO or Booklet Finisher-W PRO is attached. If the alignment guide's position is too close to the paper, a paper jam or paper crease may occur. Make sure to perform fine adjustment of the alignment guide's position. |
<Finisher Tray A Alignment Adjustment>![](./images/global_images/1T0002134966/g_ne_toggle_open.gif)
![](./images/book_images/b_key_Add.gif)
(Settings/Registration)
![](./images/book_images/b_in_arrow_right.gif)
<Adjustment/Maintenance>
![](./images/book_images/b_in_arrow_right.gif)
<Adjust Action>
You can adjust paper alignment when outputting to Tray A of a finisher.
Adjusting Paper Alignment |
You cannot align output paper in the following situations: when using paper smaller than A5R when using different size paper together If you set <Align Output Paper of Diff. Sizes (Diff. Widths)>to <On>, you can align output paper by paper width. |
|
You can switch between positive and negative values by pressing <±>. |
<Finisher Tray B Alignment Adjustment>![](./images/global_images/1T0002134966/g_ne_toggle_open.gif)
![](./images/book_images/b_key_Add.gif)
(Settings/Registration)
![](./images/book_images/b_in_arrow_right.gif)
<Adjustment/Maintenance>
![](./images/book_images/b_in_arrow_right.gif)
<Adjust Action>
You can adjust paper alignment when outputting to Tray B of a finisher.
Adjusting Paper Alignment |
You cannot align output paper in the following situations: when using paper smaller than A5R when using different size paper together If you set <Align Output Paper of Diff. Sizes (Diff. Widths)to <On>, you can align output paper by paper width. |
|
You can switch between positive and negative values by pressing <±>. |
<Finisher Output Priority Settings (Heavy 5, 6)>![](./images/global_images/1T0002134966/g_ne_toggle_open.gif)
![](./images/book_images/b_key_Add.gif)
(Settings/Registration)
![](./images/book_images/b_in_arrow_right.gif)
<Adjustment/Maintenance>
![](./images/book_images/b_in_arrow_right.gif)
<Adjust Action>
You can give priority to productivity or alignment for the output paper when using <Heavy 5> or <Heavy 6>.
|
This mode can be set when the Staple Finisher-X or Booklet Finisher-X is attached. |
<Finisher Output Priority Settings (Thin)>![](./images/global_images/1T0002134966/g_ne_toggle_open.gif)
![](./images/book_images/b_key_Add.gif)
(Settings/Registration)
![](./images/book_images/b_in_arrow_right.gif)
<Adjustment/Maintenance>
![](./images/book_images/b_in_arrow_right.gif)
<Adjust Action>
You can give priority to productivity or alignment for the output paper when using thin paper.
|
This mode can be set when the Staple Finisher-W PRO or Booklet Finisher-W PRO is attached. <Alignment Priority> is available only when outputting on Tray B of a finisher. |
<Time Until Stapling Starts in Stapler Mode>
![](./images/book_images/b_key_Add.gif)
(Settings/Registration)
![](./images/book_images/b_in_arrow_right.gif)
<Adjustment/Maintenance>
![](./images/book_images/b_in_arrow_right.gif)
<Adjust Action>
You can set the time until stapling is performed after inserting paper when using manual stapling.