<Adjust Action>

This section describes the copy and print finishing settings, such as adjusting the saddle stitch position.

<Saddle Stitch Staple Repositioning>

(Settings/Registration)

Feeds papers to the saddle stitcher unit and staples them several times, and performs the saddle stitch staple repositioning procedure. The machine performs this adjustment procedure if stapling has not been performed after you clear a staple jam or replace the staple cartridge.


Make sure to remove all output booklets from the booklet tray before performing the saddle stitch staple repositioning procedure.


Paper that is required for the saddle stitch staple repositioning procedure is automatically fed to the saddle stitcher unit by the machine. 305 mm x 457 mm, A3, B4, A4R, 11" x 17", LGL, LTRR, or custom paper sizes equivalent to these paper sizes can be used. (Make the paper source to which transparencies are registered unavailable.) This mode can be set when the Booklet Finisher-W PRO or Booklet Finisher-AC is attached.

Paper that is required for the saddle stitch staple repositioning procedure is automatically fed to the saddle stitcher unit by the machine.

305 mm x 457 mm, A3, B4, A4R, 11" x 17", LGL, LTRR, or custom paper sizes equivalent to these paper sizes can be used. (Make the paper source to which transparencies are registered unavailable.)

This mode can be set when the Booklet Finisher-W PRO or Booklet Finisher-AC is attached.

<Change Fold/Stitch Position>

(Settings/Registration)

If you notice that the saddle stitch position of the paper is not exactly in the middle of the booklet, you can make adjustments to the saddle stitch position to compensate for this error. Adjust the folding position of the paper and the saddle stitch position at the same time. Adjusting the Saddle Stitch Position

<Adjust Saddle Stitch Fold Position>

(Settings/Registration)

If you notice that the folds of the paper are not exactly in the middle of the booklet, you can make adjustments to the fold placement to compensate for this error. This mode enables you to adjust the folding position without changing the stapling position. Adjusting the Saddle Stitch Folding Position

<Adjust Double Staple Width>

(Settings/Registration)

You can adjust the double staple width.


This mode can be set when the Staple Finisher-W PRO or Booklet Finisher-W PRO is attached. When the paper width is shorter than 10 1/8" (257 mm), the double staple width is fixed to <4_3/4"> (<120 mm>). When using the Offset mode, the double staple width is fixed to <4_3/4"> (<120 mm>).

<Switch Finisher Puncher Mode>

(Settings/Registration)

You can set whether to give priority to the punching speed or to precision.


This mode can be set when the puncher unit is attached to the Staple Finisher-AC or Booklet Finisher-AC.

<Adjust Trim Width>

(Settings/Registration)

You can adjust the trimming width of Saddle Stitch printouts in 0.01" (0.1 mm) increments. When using the optional Booklet Trimmer-F, also see the included instruction manual for more information.


This mode can be set when the Booklet Trimmer-F is attached to the Booklet Finisher-W PRO.

<Color/B&W Priority for First Print Time>

(Settings/Registration)

You can set whether priority is given to color or black-and-white printing for the first print time.


The settings is only effective after the first job is processed and you have restarted the machine (by turning the main power switch OFF and then ON again). For instructions on restarting (turning the main power switch OFF and then ON) the machine, see Turning ON the Machine.

<Adjust Fold Position>

(Settings/Registration)

You can adjust the paper folding position. Adjusting the Saddle Stitch Folding Position

<Correct Curl for Each Paper Drawer>

(Settings/Registration)

This mode enables you to adjust the curl correction level of each paper source.

The curl correction level is constantly adjusted to suit the characteristics of the paper. However, if the paper curl is not corrected properly, you can manually adjust the curl correction level to accommodate the environment and the characteristics of the paper, such as moisture in the paper. Curl Correction for Each Paper Drawer

<Time Until Stapling Starts in Stapler Mode>

(Settings/Registration)

You can set the time until stapling is performed after inserting paper when using manual stapling.


This mode can be set when the Staple Finisher-AC or Booklet Finisher-AC is attached.

<Alignment Adjustment When Stapling>

(Settings/Registration)

The copied or printed paper may shrink because of temperature, humidity, or a characteristic of the paper type. In this case, this mode enables you to align copied or printed papers by adjusting the position of the alignment guide inside the finisher so as to staple the aligned papers.


This mode can be set when the Staple Finisher-W PRO or Booklet Finisher-W PRO is attached. If the alignment guide's position is too close to the paper, a paper jam or paper crease may occur. Make sure to perform fine adjustment of the alignment guide's position.

<Finisher Tray A Alignment Adjustment>

(Settings/Registration)

You can adjust paper alignment when outputting to Tray A of a finisher. Adjusting Paper Alignment


You cannot align output paper in the following situations: when using paper smaller than STMTR or A5R when using different size paper together If you set <Align Output Paper of Diff. Sizes (Diff. Widths)>to <On>, you can align output paper by paper width.


This mode can be set when the Staple Finisher-W PRO or Booklet Finisher-W PRO is attached. You can switch between positive and negative values by pressing <±>.

<Finisher Tray B Alignment Adjustment>

(Settings/Registration)

You can adjust paper alignment when outputting to Tray B of a finisher. Adjusting Paper Alignment


You cannot align output paper in the following situations: when using paper smaller than STMTR or A5R when using different size paper together If you set <Align Output Paper of Diff. Sizes (Diff. Widths)>to <On>, you can align output paper by paper width.


This mode can be set when the Staple Finisher-W PRO or Booklet Finisher-W PRO is attached. You can switch between positive and negative values by pressing <±>.

<Finisher Tray C Alignment Adjustment>

(Settings/Registration)

You can adjust paper alignment when outputting to Tray C of a finisher. Adjusting Paper Alignment


You cannot align output paper in the following situations: when using paper smaller than STMTR or A5R when using different size paper together


This mode can be set when the Staple Finisher-AC, Booklet Finisher-AC, or Finisher Jogger Kit-A is attached. You can switch between positive and negative values by pressing <±>.

<Finisher Output Priority Settings (Thin)>

(Settings/Registration)

You can give priority to productivity or alignment for the output paper when using thin paper.


This mode can be set when the Staple Finisher-W PRO or Booklet Finisher-W PRO is attached. <Alignment Priority> is available only when outputting on Tray B of a finisher.

<Finisher Output Priority Settings>

(Settings/Registration)

You can give priority to productivity or alignment for the output paper.


This mode can be set when the Staple Finisher-AC, Booklet Finisher-AC, or Finisher Jogger Kit-A is attached.