Clearing Paper Jam in the Saddle Finisher-AN (Optional) and Sub Station
(1) F-A2 Guide of the Saddle Finisher-AN and C-B1 and C-B2 Guides of the Sub Station
Follow the procedure described below, while referring to the location of the paper jam and the directions that appear on the touch panel display, to remove the jammed paper.
1.
Open the front cover of the finisher.
2.
Press the button (F-A1) as far as it can go.
This procedure is only required if the Puncher Unit-BS, Puncher Unit-BT or Puncher Unit-BU is attached.
3.
Open the guide (F-A2).
4.
Open the front cover of the fixing station.
Open the right side of the front cover first.
5.
Open the guide (C-B1).
CAUTION |
When opening the guide, be careful not to get your fingers caught, as this may result in personal injury. |
6.
Grip the lever to open the guide (C-B2).
CAUTION |
When opening the guide, be careful not to get your fingers caught, as this may result in personal injury. |
7.
Pull the jammed paper until its lead edge becomes visible on the opposite side of the paper feeding direction, and roll it in the space made available by opening the C-B2 guide.
8.
Remove the rolled paper.
9.
Lift up the guide (C-B2) and close it.
 CAUTION |
When closing the guide, be careful not to get your fingers caught, as this may result in personal injury. |
10.
Close the guide (C-B1).
| CAUTION |
When closing the guide, be careful not to get your fingers caught, as this may result in personal injury. |
11.
Close the front cover of the fixing station.
Close the left side of the front cover first.
12.
Close the guide (F-A2) of the finisher.
CAUTION |
When closing the guide, be careful not to get your fingers caught, as this may result in personal injury. |
13.
Close the front cover of the finisher.
CAUTION |
When closing the cover, be careful not to get your fingers caught, as this may result in personal injury. |
14.
Follow the instructions on the touch panel display.
NOTE |
If there is not enough space for pulling out the paper, do so while holding the C-B2 guide lifted up. Lifting up the C-B2 guide can cause it to unlock, and may result in your hand getting caught. While following the instructions, be sure to support the lifted guide with your hand. If it is difficult to remove the rolled paper, pull it out together with the primary fixing unit to remove. |
(2) F-A2 Guide of the Saddle Finisher-AN and C-C1 and C-C2 Guides of the Sub Station
NOTE |
Paper jam in this location occurs only when thick paper is delivered through the reverse unit. |
Follow the procedure described below, while referring to the location of the paper jam and the directions that appear on the touch panel display, to remove the jammed paper.
1.
Open the front cover of the finisher.
2.
Press the button (F-A1) as far as it can go.
This procedure is only required if the Puncher Unit-BS, Puncher Unit-BT or Puncher Unit-BU is attached.
3.
Open the guide (F-A2).
4.
Open the front cover of the fixing station.
Open the right side of the front cover first.
5.
Grip the guide (C-C1), and open it.
| CAUTION |
When opening the guide, be careful not to get your fingers caught, as this may result in personal injury. |
6.
Open the guide (C-C2).
7.
Pull the jammed paper downward until its lead edge becomes visible, and then fold it up.
8.
Remove the folded paper.
9.
Close the guide (C-C2).
10.
Close the guide (C-C1).
11.
Close the front cover of the fixing station.
Close the left side of the front cover first.
12.
Close the guide (F-A2) of the finisher.
CAUTION |
When closing the guide, be careful not to get your fingers caught, as this may result in personal injury. |
13.
Close the front cover of the finisher.
CAUTION |
When closing the cover, be careful not to get your fingers caught, as this may result in personal injury. |
14.
Follow the instructions on the touch panel display.