Staple Finisher-X/Booklet Finisher-X/Puncher Unit-BF/Puncher Unit-BG (for the 230 V Machine Only)/Inner Booklet Trimmer-A
85FE-03C
Installing "Staple Finisher-X" or "Booklet Finisher-X" enables you to use the following finish functions.
Collate The printouts are collated into sets arranged in page order of the document.
Group All printouts of the same original page are grouped together into sets.
Offset Each printout group is shifted in alternating layers.
Staple + Collate The printouts are collated into sets arranged in page order and stapled (Corner/Double). You can fold and staple the printouts by using "Booklet Finisher-X."
Staple + Group All printouts of the same original page are grouped together into sets and stapled (Corner/Double).
Saddle Fold (Booklet Finisher-X only) The printouts are folded into half its size.
TIPS
If you install the "Puncher Unit-BF" or "Puncher Unit-BG (for the 230 V machine only)" in the "Staple Finisher-X" or "Booklet Finisher-X," you can punch holes in your printouts.
If you install the "Inner Booklet Trimmer-A" in the "Booklet Finisher-X," you can cut the bound output paper to align the edge of the paper.
If you install the "Multi Function Professional Puncher-B" in the "Booklet Finisher-X," you can punches several types of holes. For more information on the "Multi Function Professional Puncher-B," see the instruction manual of the "Multi Function Professional Puncher-B."
External View
Booklet Finisher-X
Staple Finisher-X
Output Tray A
The prints are output to this tray. You can specify functions for which the tray is used by configuring <Output Tray Settings>. <Output Tray Settings>
Front cover
Open to remove jammed paper, clear a staple jam in the stapler unit and saddle stitcher unit, or replace the staple cartridge. If the "Puncher Unit-BF" is installed, open to discard punch waste.
Booklet tray (Booklet Finisher-X only)
The printouts that are saddle stitched are output to this tray.
Output Tray C
The prints are output to this tray. You can specify functions for which the tray is used by configuring <Output Tray Settings>. <Output Tray Settings>
Output Tray B
The prints are output to this tray. You can specify functions for which the tray is used by configuring <Output Tray Settings>. <Output Tray Settings>
The maximum number of bindable sheets may not be possible, depending on the paper type. In this case, change the paper type, or reduce the number of sheets to bind.
Collate and group
If you select <Offset> in combination with the collate or group function, each printout group is shifted.
The output trays move downward as the output paper stacks accumulate. Once an output tray has reached its stacking limit, subsequent prints are automatically delivered to the next available tray. If all of the available trays have reached their stacking limits, printing stops. Remove all of the output paper from the trays to resume printing.
Staplers
When you are using the Staple mode, do not remove the stack of paper from the output tray during the job. Remove the stack of paper when the job has been completed.
If the <Load staples into the stapler unit.> message appears, almost all of the staples have been used. To proceed, replace the staple cartridge.
If a tray reaches the lowest position limit, printing stops temporarily. Remove all of the output paper from the tray to resume printing.
Saddle stitch
The accuracy of folds may vary depending on the paper type and the number of sheets.
This site uses cookies to provide its contents and functions and improve their qualities etc. You can find out more about our use of the cookies here. If you select "Reject", only cookies necessary to provide the contents and functions of the site are recorded and stored.