Cleaning the Feeder

If any of the following problems occurs when the document is scanned from the feeder, then perform feeder cleaning.
The document cannot be scanned clearly
The size of the document cannot be detected correctly
The document gets dirty during scanning
Paper jam occurs frequently

When the 2-Sided Single Pass Feeder (Single Pass DADF-C) is attached

The Single Pass DADF-C is an optional product. However, depending on the model of your machine, this product may be standard-equipped.
1
Turn the power OFF, and remove the power plug from the power outlet.
Turning OFF the Machine
Check the operation status of the machine before turning the power OFF. You can turn the power OFF even if the machine is executing an operation, but this may cause the operation to be interrupted or data to become damaged.
2
Pull the lever, and open the feeder cover.
3
Clean the rollers inside the feeder cover.
Wet a soft cloth with water and wring it out well, then wipe the rollers with it. Afterwards, wipe the rollers with a soft and dry cloth.
Make sure that no trash such as pieces of paper gets into the groove of the multiple sheet feed detection sensor. If trash does get in, remove it using a soft cloth.
If the rollers and surrounding areas are very dirty, clean them out. To do this, wet a cloth with water and wring it out well, then wipe the dirty areas. Afterwards, wipe the areas with a soft and dry cloth.
4
Gently close the feeder cover.
5
Open the feeder.
6
Wipe the document feed scanning area on the platen glass side.
Wipe the thin glass strip () and the white plate ().
Wipe the area with the included cleaning cloth. If you cannot remove the dirt, wet a soft cloth with water and wring it out well, then wipe the machine with it. Afterwards, wipe the machine with a soft and dry cloth.
Wait until the moisture has completely dried before proceeding to the next step.
7
Wipe the document feed scanning area on the feeder side.
Pull the top lever to open the document feed scanning area cover.
Gently open the cover so that you do not damage the platen glass.
Open the inner cover.
Wipe the document feed scanning area.
Wipe the thin glass strip () and the white plate ().
Wet a soft cloth with water and wring it out well, then wipe the machine with it. Afterwards, wipe the machine with a soft and dry cloth.
Wait until the moisture has completely dried before proceeding to the next step.
Close the inner cover.
Close the document feed scanning area cover until it clicks into place.
8
Gently close the feeder.
9
Insert the power plug into the power outlet, and turn the power ON.
Turning ON the Machine
If streaks still appear on the originals or paper after the feeder cleaning operation
Load about 10 sheets of A4 size paper in the feeder and perform the following procedure to execute <Clean Feeder>. When a message indicating that cleaning is complete is displayed, try using the feeder to copy an original to check if the problem has been resolved.
It takes approximately 20 seconds to clean the feeder.

When the 2-Sided Double Pass Feeder (DADF-BA) is attached

The DADF-BA is an optional product. However, depending on the country or region, this product may not be available.
Spin the rollers while cleaning them.
1
Turn the power OFF, and remove the power plug from the power outlet.
Turning OFF the Machine
Check the operation status of the machine before turning the power OFF. You can turn the power OFF even if the machine is executing an operation, but this may cause the operation to be interrupted or data to become damaged.
2
Pull the lever, and open the feeder cover.
3
Clean the rollers inside the feeder cover.
Wet a soft cloth with water and wring it out well, then wipe the rollers with it. Afterwards, wipe the rollers with a soft and dry cloth.
If the rollers and surrounding areas are very dirty, clean them out. To do this, wet a cloth with water and wring it out well, then wipe the dirty areas. Afterwards, wipe the areas with a soft and dry cloth.
4
Clean the inside of the inner cover of the feeder.
Open the inner cover of the feeder.
Wipe the transparent plastic.
Wet a soft cloth with water and wring it out well, then wipe the plastic with it. Afterwards, wipe the plastic with a soft and dry cloth.
Wait until the moisture has completely dried before proceeding to the next step.
Wipe the rollers (a total of three places) inside the inner cover.
Wet a soft cloth with water and wring it out well, then wipe the rollers with it. Afterwards, wipe the rollers with a soft and dry cloth.
Wait until the moisture has completely dried before proceeding to the next step.
Close the inner cover of the feeder.
When closing the inner cover of the feeder, be careful not to get your fingers caught, as this may result in personal injury.
5
Clean the document feed scanning area (thin glass strip) and the white area (rollers and plate).
Open the feeder.
Clean the white plate.
Wet a soft cloth with water and wring it out well, then wipe the plate with it. Afterwards, wipe the plate with a soft and dry cloth.
Wait until the moisture has completely dried before proceeding to the next step.
Clean the document feed scanning area.
Wet a soft cloth with water and wring it out well, then wipe the area with it. Afterwards, wipe the area with a soft and dry cloth.
Wait until the moisture has completely dried before proceeding to the next step.
Close the feeder.
When closing the feeder, be careful not to get your fingers caught, as this may result in personal injury.
6
Gently close the feeder cover.
When closing the feeder cover, be careful not to get your fingers caught, as this may result in personal injury.
7
Insert the power plug into the power outlet, and turn the power ON.
Turning ON the Machine
If streaks still appear on the originals or paper after the feeder cleaning operation
Load about 10 sheets of A4 size paper in the feeder and perform the following procedure to execute <Clean Feeder>. When a message indicating that cleaning is complete is displayed, try using the feeder to copy an original to check if the problem has been resolved.
It takes approximately 15 seconds to clean the feeder.

85E3-01F