Correcting Distortion (Trapezoid)

This setting enables you to correct the image shape by equalizing the length of the right and left side of the printing area when the image is printed like a trapezoid.
You can also make the adjustment by using the guide sheet or test page.
- When scanning with the feeder Adjusting the Image Position Using the Test Page (When Using a Feeder)
- When scanning with the platen glass Adjusting the Image Position Using the Guide Sheet (When Using the Platen Glass)

1
Press <Change> for <Adjust Image Position>.
2
Press <Do Not Use Scanner> or <Adjust Manually>.
This procedure is not necessary if the optional “Duplex Color Image Reader Unit-P” and “Sensing Unit-B” are not installed.
3
Press <Set Details>  <Corr. Distortion (Trapezoid)>.
If you want to enter the values of the test page you measured manually:
To adjust the image position on long sheets, print out a long sheet test page. The adjustment can be made more efficiently than with the test page printed out by <Output Test Page> under <Correct Distortion (Trapezoid)>. (The long sheet test page is available from the online manual site.)
Press <Output Test Page>.
Enter the number of test page to make, and press <Next>.
If the image position varies greatly, the accuracy of correction may be improved by printing several test pages and using an average of the measured length.
Select a paper source that contains a custom paper size, and press <Start Printing>.
The test page is printed.
Measure the length of the 'b' and 'h' marks on the test page.
The mark 'b' is printed on the right side and the mark 'h' is printed on the left side of the feeding direction.
Standard size
Long sheet
Example: 'b' = 360.0 mm, and 'h' = 355.5 mm
Return to the <Correct Distortion (Trapezoid)> screen, and enter the measured length of <b> and <h> for front and back sides.
Using the following two numerical values and "c = 250.0", a device adjusts the length to correct distortion on the printing area.
<b>:
Enter the measured length of 'b' mark on the test page (for the long sheet: the measured length of 'b' mark that is closest to the tail edge of the paper).
<h>:
Enter the measured length of 'h' mark on the test page (for the long sheet: the measured length of 'h' mark that is closest to the tail edge of the paper).
Following the example, enter 360.0 for <b> and 355.5 for <h>.
The difference between 'b' and 'h' (0.5 mm) is corrected.
Press <OK>.
Print a test page again and check the image position as needed. If you need to make a further adjustment, repeat steps above.
If you correct the position using any printed images:
Check the image position on the output paper.
Example: 'c' = 200.0 mm, 'b' = 300.0 mm, and 'h' = 299.5 mm
Measure the following length on the output paper and enter the measured length.
Using the following three numerical values, a device adjusts so that the distorted printing area may be corrected.
<c>:
Enter the measured length from the left side lead edge of the printing area to the right side lead edge of the printing area.
<b>:
Enter the measured length from the right side lead edge of the printing area to the right side tail end of the printing area.
<h>:
Enter the measured length from the left side lead edge of the printing area to the left side tail end of the printing area.
Following the example, enter 200.0 for <c>, 300.0 for <b>, and 299.5 for <h>.
The difference between 'b' and 'h' (0.5 mm) is corrected.
Press <OK>.
Print a test page again and check the image position as needed. If you need to make a further adjustment, repeat steps above.
4
Press <OK>  <OK>.
To restore the accumulated value, press <Restore Initial Settings>.
A723-088