Inner Finisher-F1

The Inner Finisher-F1 is equipped with the following modes: Collate, Group, Offset, and Staple. (See "Finishing Modes.")

If the Copy Tray-J1 is attached to the right side of the machine, prints can be delivered to two different locations. Additionally, if the Inner Finisher Additional Tray-A1 is attached, prints can be delivered to three different locations.

Parts and Their Functions

Finishing Modes

CAUTION
Do not place your hand in the part of the tray where stapling is performed (near the rollers) if a finisher is attached, as this may result in personal injury. Do not place your fingers or hands on the finisher when the finisher is in use. Doing so may result in personal injury or damage to the finisher.

IMPORTANT
Since the trays of the finisher move during copying/printing, do not place anything under the trays, as doing so may damage the trays.

Parts and Their Functions

1.	Auxiliary Tray Pull out the auxiliary tray if you are outputting large size paper.
2.	Output Tray Paper is output to the output tray.
3.	Inner Finisher Additional Tray-A1 The Inner Finisher Additional Tray-A1 can be attached to the Inner Finisher-F1 to provide an additional paper output tray.
4.	Front Cover Open this cover to replace the staple cartridge in the stapler unit, or to clear a staple jam.

Finishing Modes

The Inner Finisher-F1 is equipped with the following finishing modes.

Collate Mode

The prints are automatically collated into sets arranged in page order.

Group Mode

All prints of the same original page are grouped together into sets.

Offset Mode

The print output is shifted alternately to the front and back of the tray.
The paper is output in a vertical (portrait) or horizontal (landscape) orientation, depending on the orientation of your originals. For example, for A4R originals, the paper is output in the horizontal direction. For A4 originals, the paper is output in the vertical direction.

Staple Mode

The prints are automatically collated into sets arranged in page order and stapled. Prints are stapled in the following places:

If an original is placed on the platen glass:

Corner Staple Area		Double Staple Area

1 Upper Left 2 Upper Right 3 Lower Right 4 Lower Left		1 Left Side 2 Right Side

If originals are placed in the feeder:

Corner Staple Area		Double Staple Area

1 Upper Right 2 Upper Left 3 Lower Left 4 Lower Right		1 Right Side 2 Left Side

The following are paper sizes that can be output from the output trays of the machine. However, some paper sizes may not be output depending on the set functions.

: Available

-: Unavailable

Paper Size		Output Tray
305 x 457 mm
SRA3
A3
A4
A4R
A5
A5R
Envelope*	No. 10 (COM10)
	Monarch
	DL
	ISO-C5
	Nagagata 3
	Yougatanaga 3
	Kakugata 2
Custom Size	99 mm x 139.7 mm to 320 mm x 457.2 mm

* Vertically placed envelopes cannot be output.

IMPORTANT
If the Inner Finisher-F1 is attached, the Inner 2Way Tray-F1 cannot be attached. The following paper sizes can be stapled: A3, A4, A4R You cannot staple envelopes, transparencies, tracing paper, or labels.

NOTE
For instructions on general maintenance for the finisher, such as replacing staples, see "Maintenance." For instructions on resolving problems, such as paper jams and staple jams, see "Problem Solving." The maximum number of sheets (including cover sheets) that can be stapled together is 30 sheets for A3 and A4R paper, and 50 sheets for A4 paper. If the machine stops while stapling and the message <Load staples into the stapler unit.> appears, almost all of the staples have been used, and the staple cartridge must be replaced. To proceed, replace the staple cartridge. If the Collate, Group, or Staple mode is set, the output trays move downward as the stack of paper that is output increases in quantity and thickness, and printing may temporarily stop after the paper is output in the following cases. To resume printing, remove all of the prints from the output tray. When the position of the tray reaches the lower limit When 30 sets are printed (with the Staple mode set) If you press [Offset] when either the Collate or Group mode is set, each set of prints is shifted alternately to the front and back of the tray before it is delivered to the output tray.

NOTE

For instructions on general maintenance for the finisher, such as replacing staples, see "Maintenance." For instructions on resolving problems, such as paper jams and staple jams, see "Problem Solving."

The maximum number of sheets (including cover sheets) that can be stapled together is 30 sheets for A3 and A4R paper, and 50 sheets for A4 paper.

If the machine stops while stapling and the message <Load staples into the stapler unit.> appears, almost all of the staples have been used, and the staple cartridge must be replaced. To proceed, replace the staple cartridge.

If the Collate, Group, or Staple mode is set, the output trays move downward as the stack of paper that is output increases in quantity and thickness, and printing may temporarily stop after the paper is output in the following cases. To resume printing, remove all of the prints from the output tray.

When the position of the tray reaches the lower limit

When 30 sets are printed (with the Staple mode set)

If you press [Offset] when either the Collate or Group mode is set, each set of prints is shifted alternately to the front and back of the tray before it is delivered to the output tray.