CAUTION
|
Do not place your hand in the part of the tray where stapling is performed (near the rollers) if a finisher is attached, as this may result in personal injury.
Do not place your fingers or hands on the finisher when the finisher is in use. Doing so may result in personal injury or damage to the finisher.
|
IMPORTANT
|
Since the trays of the finisher move during copying/printing, do not place anything under the trays, as doing so may damage the trays.
|
1.
|
Auxiliary Tray
Pull out the auxiliary tray if you are outputting large size paper.
|
2.
|
Output Tray
Paper is output to the output tray.
|
3.
|
Staple Button
Press this button when performing manual stapling.
|
4.
|
Slit
Insert paper here when performing manual stapling.
|
5.
|
Finisher Entrance Guide
Open this guide when clearing a paper jam. |
6.
|
Main Unit's Right Cover
Open this cover when clearing a paper jam inside the main unit. |
7.
|
Front Cover
Open this cover to replace the staple cartridge or clear a staple jam in the stapler unit. |
IMPORTANT
|
The Eco (Staple-Free) mode may only be able to bind less than five sheets of paper or the binding may be weak, depending on the usage environment, paper weight, and paper type, etc.
|
Corner Staple/Eco (Staple-Free) Area
|
Double Staple Area
|
|
*1 Upper Left
*2 Upper Right
*3 Lower Right
*4 Lower Left
|
*5 Left Side
*6 Right Side
|
Corner Staple/Eco (Staple-Free) Area
|
Double Staple Area
|
|
*1 Upper Right
*2 Upper Left *3 Lower Left *4 Lower Right |
*5 Right Side
*6 Left Side |
Paper Size
|
Output Tray
|
|
A3
|
||
A4
|
||
A4R
|
||
A5
|
||
A5R
|
||
B4
|
||
B5
|
||
B5R
|
||
Envelope
|
No.10(COM10)
|
|
Monarch
|
||
DL
|
||
ISO-C5
|
||
Nagagata 3
|
||
Yougatanaga 3
|
||
Kakugata 2
|
||
Custom Size
|
98.4 mm x 139.7 mm to 320 mm x 457.2 mm
|
|
Free Size
|
98.4 mm x 139.7 mm to 320 mm x 457.2 mm
|
IMPORTANT
|
If the Inner Finisher-G1 is attached, the Inner 2way Tray-J1 cannot be attached.
The 3 Way Unit-D1 is required to output to the upper tray of the Inner Finisher-G1.
The following paper sizes can be stapled: A3, B4, A4, A4R, B5
Only A3, B4, A4, and B5 paper can be bound with the Eco (Staple-Free) mode.
You cannot staple envelopes, transparencies, tracing paper, or labels.
The Eco (Staple-Free) mode cannot be used for heavy paper, 1-sided coated paper, 2-sided coated paper, envelopes, transparencies, tracing paper, labels, or bond paper.
|
NOTE
|
For instructions on general maintenance for the finisher, such as replacing staples, see "Maintenance." For instructions on resolving problems, such as paper jams and staple jams, see "Problem Solving."
The maximum number of sheets (including cover sheets) that can be stapled together is 50 sheets.
A maximum of five sheets of paper can be bound with the Eco (Staple-Free) mode.
If the machine stops while stapling and the message <Load staples into the stapler unit.> appears, almost all of the staples have been used, and the staple cartridge must be replaced. To proceed, replace the staple cartridge.
If the Collate, Group, or Staple mode is set, the output trays move downward as the stack of paper that is output increases in quantity and thickness, and printing may temporarily stop after the paper is output in the following cases. To resume printing, remove all of the prints from the output tray.
When the position of the tray reaches the lower limit
When 30 sets are printed (with the Staple mode set)
If you press [Offset] when either the Collate or Group mode is set, each set of prints is shifted alternately to the front and back of the tray before it is delivered to the output tray.
|