Loading Tab Paper
This section describes how to load tab paper.
You can load tab paper to the following paper source:
Paper drawers of the main unit
Stack Bypass-B1
POD Deck Lite-C1
Multi-drawer Paper Deck-C1
Document Insertion Unit-N1
IMPORTANT |
Only A4 tab paper can be used. |
NOTE |
When you load tab paper into the paper drawer, POD Deck Lite-C1, or Multi-drawer Paper Deck-C1, make sure to register the paper type. (See "Registering the Paper Size and Type for a Paper Source.") Make sure that you fan the sheets of tab paper well before placing them. Otherwise multiple sheets of tab paper may be fed at a time and images may not be printed correctly on the tab paper. |
How to Load Tab Paper
There are two kinds of tab paper: right order tab paper and reverse order tab paper.
 |  |
Right Order Tab Paper | Reverse Order Tab Paper |
IMPORTANT |
You cannot make copies or prints on tab paper that is loaded in the Document Insertion Unit-N1. |
NOTE |
You can use tab paper set in the Document Insertion Unit-N1 for Add Cover, Insert Sheets or Job Separator. If you want to insert printed tab paper as a chapter pages, insert a blank paper where the tab paper will be inserted. |
Paper Source | How to Load Tab Paper | |
Paper Drawer |  | Reverse Order/Face Down |
Stack Bypass-B1 |  | Normal Order/Face Up |
POD Deck Lite-C1 | | Normal Order/Face Up |
Multi-drawer Paper Deck-C1 | | Normal Order/Face Up |
Document Insertion Unit-N1 | | Reverse Order/Face Down |
NOTE |
For more information on selecting the paper size or type of the Stack Bypass-B1, see "Loading Paper into the Stack Bypass-B1." For more information on aligning the size change plate for the POD Deck Lite-C1, see "Changing the Paper Size for the POD Deck Lite-C1." For more information on aligning the size change plate for the Multi-drawer Paper Deck-C1, "Changing the Paper Size for the Multi-drawer Paper Deck-C1." For more information on selecting the paper size or type of the Document Insertion Unit-N1, see "Loading Paper into the Document Insertion Unit-N1 (Optional)." |
Loading Tab Paper
NOTE |
When loading tab paper into the paper drawer, the Tab Feeding Attachment-F1 is required. |
1.
Open the paper drawer.
2.
Remove the Tab Feeding Attachment-F1 from its holder by sliding it to the left and lifting it up, and place it as shown below.
 | 1. Remove the Tab Feeding Attachment-F1. |
2. Place the Tab Feeding Attachment-F1 aligning to the mark for tab paper (A4), and fix the Tab Feeding Attachment-F1 by fastening the blue screws. |
3.
Load the tab paper face down with the tabs facing left.
 | |
4.
Squeeze the upper part of the front guide. Without releasing it, slide the front guide to align it with the mark for tab paper (A4).
IMPORTANT |
Slide the front guide until it clicks into place. If the front guide is not adjusted properly for the paper size loaded in the paper drawer, the correct paper size may not appear on the touch panel display. Adjust the front guide correctly to avoid causing a paper jam, dirty prints, or make the inside of the machine dirty. |
5.
Gently push the paper drawer back into the machine until it clicks into place in the closed position.
 CAUTION |
When returning the paper drawer to its original position, be careful not to get your fingers caught, as this may result in personal injury. |
IMPORTANT |
Paper which has been rolled or curled must be straightened out prior to use. You will not be able to make copies or print if you load paper that exceeds the loading limit mark (  ) or if the paper drawer is not completely pushed into the machine.Make sure that the height of the paper stack does not exceed the limit mark ( ) at the back of the paper drawer.Always check that the paper drawers are in place. Never place paper or any other items in the empty part of the drawer next to the paper stack. Doing so may cause paper jams. When you are not loading tab paper, make sure to return the Tab Feeding Attachment-F1 to its holder. Using the Tab Feeding Attachment-F1 for storing paper other than tab paper may cause a paper jam. |