Countermeasures for Each Error Code
If an error occurs such as when printing is not successful or when you cannot send or receive a fax or scanned original, the corresponding error code is displayed in a report or in the job log screen as a three-digit number. Check the following to find out causes and solutions for each error code. For how to print an error report and information in the report, see
Printing Reports and Lists. For details of the job log screen, see
<Status Monitor> Screen.
#001
An original jams in the feeder.
#003
A fax could not be sent or received due to its large data size.
When receiving a fax: Ask the sender to divide the original into multiple sections or reduce the resolution before sending.
#005
A fax could not be sent because the recipient's machine did not respond within 35 seconds.
When the recipient's machine is turned OFF or the line is busy, a fax may not be sent. Ask the recipient to check the machine status. When sending the fax overseas, insert pauses in the fax number.
Basic Operations for Sending Faxes#012
A fax could not be sent because the recipient's machine ran out of paper.
Ask the recipient to reload the paper.
#018
A fax could not be sent since the recipient's machine did not respond because the line was busy or for other reasons.
When the recipient's machine is turned OFF or the line is busy, a fax may not be sent. Ask the recipient to check the machine status. When sending the fax overseas, insert pauses in the fax number.
Basic Operations for Sending Faxes#022
Sending of a fax from a computer is disabled.
A fax could not be forwarded because the specified destination was deleted from the Address Book.
#037
A fax could not be sent because the memory is full.
If a job queued, wait until the job is completed.
If sending an original with many pages, divide it into multiple sections.
The file is too large to print.
Optimize the file to reduce the size or divide the file into sections, and then proceed to printing again.
Try printing from the printer driver. This may work well.
#099
An operation that caused a job to be canceled has been performed.
When you cancel a job, this error code is displayed, but this is not abnormal. Print, send, or receive documents again as necessary.
#401
A scanned original could not be stored to a USB memory device due to insufficient memory space.
#406
A scanned document could not be stored to a USB memory device due to an error.
Reduce the number of originals to scan.
#408
Read failed because the USB memory device was removed while data was being read from it.
The connected USB memory device is using an unsupported format.
#701
Authentication failed because an incorrect Department ID or PIN was entered when the Department ID Management was activated.
Enter the correct Department ID and PIN.
Continuing operating without entering a Department ID was attempted even though unknown-ID jobs (functions that permit operations without a Department ID and PIN) were disabled in the Department ID Management.
#703
Data could not be written because the memory space that was allocated for images was full when sending an e-mail/I-Fax or storing to a shared folder/FTP server.
If another sending document is queued, wait for a while until it is completed, and send again.
Divide the document into multiple sections before sending.
Delete the documents that are stored in memory.
Turn OFF the machine, wait for at least 10 seconds, and turn it back ON.
#751
The FTP server has not been started up or a network connection has been cut.
(Failure to connect to the destination is sometimes caused by a disconnection en route.)
Check the destination.
The IP address was not set correctly.
#752
E-mail sending or I-Fax sending/receiving was impossible because an incorrect SMTP/POP3 server name was set.
E-mail sending or I-Fax sending/receiving was impossible because an incorrect domain name was set.
E-mail sending or I-Fax sending/receiving was impossible because the machine was not connected to a network correctly.
Check whether the machine is properly installed and correctly connected to the network.
Settings Problems#753
Scanned data could not be sent as e-mail, not sent/received as I-Fax, or not stored in the shared folder/FTP server because the LAN cable is disconnected.
#755
Scanned data could not be sent as e-mail or I-Fax nor stored in the shared folder or FTP server because TCP/IP was not working correctly.
Check <TCP/IP Settings>, and set correctly.
<Network>An IP address is not set.
The machine cannot communicate with devices on a network immediately after the machine starts up because the waiting time for the start of the communication is set.
The machine cannot start communicating immediately after it is turned ON. Wait until the set time for <Waiting Time for Connection at Startup> passes after turning ON the machine, and send again.
Setting a Wait Time for Connecting to a Network#766
The certificate has expired.
Update the certificate or use a certificate that has not expired.
#801
When communicating with an SMTP server to send an e-mail/I-Fax, a timeout error occurred from the server.
Check whether SMTP is running on the network correctly.
Check whether the machine is properly installed and correctly connected to the network.
Settings ProblemsWhen communicating with the SMTP server, an error returned from the server.
Check whether the SMTP server is set correctly.
A destination is not set correctly.
Check whether the destination is set correctly.
When storing a scanned original into the shared folder, an error occurred from the folder.
Check whether the shared folder and the computer that has the shared folder are running correctly.
The incorrect folder name or password was specified when storing to the shared folder.
Check the destination settings.
#802
The SMTP/POP3/FTP server name is not set correctly.
#804
No access privileges to access the shared folder/FTP server are granted.
Assign the privilege for writing data to the storage folder to the sender (user name registered in the destination). For details, contact your Network Administrator.
The incorrect folder name was specified when storing to the shared folder/FTP server.
Check the destination settings.
#806
When storing data to a shared folder/FTP server, an incorrect user name or password was specified.
When sending an e-mail/I-Fax, an incorrect destination was specified.
Enter the correct e-mail address, and send the message again. If the destination that was registered in the Address Book was used, check whether the e-mail address is correct.
Registering Destinations#808
An error or timeout occurred on the FTP server.
#810
An error has been returned from the POP3 server when sending an e-mail or sending/receiving I-Fax.
Check whether the POP3 server is set correctly.
Check whether your mail server and network are running correctly. For more information, contact your Network Administrator.
#813
The login name or the password that is used on the POP3 server is not set correctly.
Correctly enter the login name or the password that is used on the POP3 server.
#816
The number of print pages has reached the upper limit specified for the department.
#818
The received data is in a file format that the machine cannot print.
Contact the other party and ask them to resend the data in a different file format.
#819
The received data is not supported (incorrect MIME information).
Contact the other party and ask them to check the settings and then resend the data.
#820
The received data is not supported (incorrect BASE64 or uuencode information).
Contact the other party and ask them to check the settings and then resend the data.
#821
The received data is not supported (a TIFF analysis error occurred).
Contact the other party and ask them to check the settings and then resend the data.
#822
A file in a USB memory device could not be printed because the format of the file is not supported.
#827
The received data is not supported (includes unsupported MIME information).
Contact the other party and ask them to check the settings and then resend the data.
#829
The received data exceeds the maximum receivable size.
In fax reception, the machine deletes the data for page 1,000 onwards and either prints the first 999 pages or holds them in memory. Get the sender to resend page 1,000 onwards.
In I-Fax reception, the machine cannot receive the e-mail if its size exceeds 24 MB. Ask the sender to reduce the size of the e-mail down to under 24 MB and try resending.
#839
A user name and password that are used for SMTP authentication are not set correctly.
#841
When sending an e-mail/I-Fax, an encryption algorithm that is common to the mail server is not present.
Add the common encryption algorithm to the mail server settings.
A TLS server certificate verification error has occurred during communication with the SMTP server.
Check that the CA certificate that signed the TLS server certificate on the SMTP server side is registered to the machine by using the Remote UI.
Check that the TLS server certificate on the SMTP server side is valid.
Check that the TLS server certificate is not a self-signed one.
#844
TLS encrypted communication to a POP3 server failed when sending an e-mail with POP before SMTP.
Check the TLS encrypted communication settings in the POP3 server.
Clear the [Use TLS for POP] check box. If the problem persists, clear the [Use POP Authentication Before Sending] check box, and set the communication setting to a setting other than POP before SMTP.
Configuring E-Mail/I-Fax Communication SettingsWhen verifying a TLS server certificate to communicate to the POP3 server, a verification error occurred.
Check that the CA certificate that signed the TLS server certificate on the POP3 server side is registered to the machine by using the Remote UI.
Check that the TLS server certificate on the POP3 server side is valid.
Check that the TLS server certificate is not a self-signed certificate.
#846
An e-mail or I-Fax could not be sent due to a POP authentication failure.
#852
The machine turns OFF for some reason.
Check whether the power plug is inserted into an outlet firmly.
#853
A document could not be printed because its data size exceeded the machine's upper processing capability.
The machine may not be able to print documents with many pages. Reduce the number of pages per printing, or print when no print job is queued or no document is being printed. If you are still unable to print, check the document data for any defects.
Printing was canceled from the computer.
If you cancel an operation when the print data is being sent to the machine from a computer, this error code is displayed, but this is not abnormal. Print again as necessary.
A secured document that was left unprinted was deleted.
If the secured document is not printed within a specific period of time (30 minutes by default), it is deleted from memory. Send the secured document again, and print it within the period.
Printing via Secure PrintPrinting using Secure Print was attempted when Secure Print was restricted.
When <Use Secure Print> is set to <Off>, you cannot use Secure Print. Set the setting to <On> and print again.
Printing via Secure PrintYou tried to print a file that is either corrupted or not supported.
Password protected PDF files could not be printed.
#861
A document could not be printed because a printer driver that was not intended for this machine was used.
A document could not be printed due to a defect in its data.
Check the document data for any defects.
#862
Settings are included which are not supported, cannot be combined, or otherwise exceed the limits of the machine.
Check the job settings.
#863
An error occurred when printing from a computer.
Turn OFF the machine, wait for at least 10 seconds, and turn it back ON. After the restart is complete, try printing again.
#995
A document waiting to be sent or received was canceled.
Sent or received the document again as necessary.