Layout
| The settings about print appearance including gutter margins and print positions are listed with short descriptions. Default settings are marked with a dagger ( ![](./images/book_images/pubnumbers/USRMA-4297/b_dagger.gif) ). |
Number of Copies![](./images/global_images/1T0002134966/g_ne_toggle_open.gif)
Specify the number of copies.
1 ![](./images/book_images/pubnumbers/USRMA-4297/b_dagger.gif) to 9999 |
Offset Y/Offset X![](./images/global_images/1T0002134966/g_ne_toggle_open.gif)
You can specify settings for shifting the print position for all types of printing in 0.5 mm increments regardless of the paper source.
-50.0 to 0.0 ![](./images/book_images/pubnumbers/USRMA-4297/b_dagger.gif) to +50.0 (mm) |
<Offset Y>
Shifts the print position vertically.
<Offset X>
Shifts the print position horizontally.
Offset values
For <Offset Y>, set a plus (+) value to shift the print position downward. For <Offset X>, set a plus (+) value to shift the print position rightward. Set a minus (-) value to shift the print position in the opposite direction.
Specifying fine settings for the print position |
You can select <Adj. Print Position> under <User Maintenance> to finely specify the print position for each paper source. The range of available offset values is from -5.0 mm to +5.0 mm. Adjusting Print Position |
Binding Location![](./images/global_images/1T0002134966/g_ne_toggle_open.gif)
Select whether to bind the long edge or short edge of the printouts with a binding tool such as a stapler. In this case, specify settings for <Gutter> to adjust the binding margin, as well.
Long Edge ![](./images/book_images/pubnumbers/USRMA-4297/b_dagger.gif) Short Edge |
<Long Edge>
Select to bind the printouts along the long edge.
<Short Edge>
Select to bind the printouts along the short edge.
Gutter![](./images/global_images/1T0002134966/g_ne_toggle_open.gif)
Adjust the margin width of the edge specified in <Binding Location> by shifting the print position of the print data. If you select "0.0", the margin will not be changed.
-50.0 to 0.0 ![](./images/book_images/pubnumbers/USRMA-4297/b_dagger.gif) to +50.0 (mm) |
Margin values
Specify the direction and width for shifting the print position of the print data. The edge where the margin is changed varies depending on whether a "+" or "-" value is set. You can adjust the margin width in 0.5 mm increments.
Portrait-oriented documentSetting Value | Long edge binding | Short edge binding |
"+" value | Left end of paper (for left binding) | Upper end of paper (for top binding) |
"-" value | Right end of paper (for right binding) | Lower end of paper (for bottom binding) |
Landscape-oriented documentSetting Value | Long edge binding | Short edge binding |
"+" value | Left end of paper (for top binding) | Upper end of paper (for right binding) |
"-" value | Right end of paper (for bottom binding) | Upper end of paper (for right binding) |
Alternative Method![](./images/global_images/1T0002134966/g_ne_toggle_open.gif)
When you perform 2-sided printing of a document that consists of an odd number of pages, you can select whether to process the last page in 1-sided printing mode. If you select <On>, the printing will be finished faster than the regular 2-sided printing.
Off On ![](./images/book_images/pubnumbers/USRMA-4297/b_dagger.gif) |
|
When the printing of a document consisting of an even number of pages finishes in 1-sided printing modeIn the following cases, the last page is processed in 1-sided printing mode even if the document consists of an even number of pages. The last page is blank. The last page cannot be printed for a reason such as the paper size is not available for 2-sided printing. When paper with preprinted logo is usedIf the last page is processed in 1-sided printing mode with <Alternative Method> to <On>, the orientation or print side of the last page may not match those of other pages. In this case, set <Alternative Method> to <Off>. |