<Adjust Action>

Specify the settings for adjusting the machine's actions.
 
For information on the items ("A", "B", "C", and "No") in the "Import All Function" column, see Import All Function.
Item marked with an asterisk (*)
Only appears if you have the option installed. Checking the Options Installed on This Machine

<Saddle Stitch Staple Repositioning> *

 (Settings/Registration)  <Adjustment/Maintenance>  <Adjust Action>
Feeds papers to the saddle stitcher unit and staples them several times, and performs the saddle stitch staple repositioning procedure. The machine performs this adjustment procedure if stapling has not been performed after you clear a staple jam or replace the staple cartridge.
Item
Setting Description
DeviceAdmin
NetworkAdmin
Can be set in Remote UI
Device Information Delivery Available
Import All Function
Name of Item When Exporting with the Remote UI
<Saddle Stitch Staple Repositioning>
<Start>
Yes
Yes
No
No
No
-
Make sure to remove all output booklets from the booklet tray before performing the saddle stitch staple repositioning procedure.
8700 Series / 6700 Series Only
Make sure to remove the paper that was used for adjustment.
Paper that is required for the saddle stitch staple repositioning procedure is automatically fed to the saddle stitcher unit by the machine.
305 mm x 457 mm, A3, B4, A4R, 11" x 17", LGL, LTRR, or custom paper sizes equivalent to these paper sizes can be used. (Make the paper source to which transparencies are registered unavailable.)

<Change Fold/Stitch Position> *

 (Settings/Registration)  <Adjustment/Maintenance>  <Adjust Action>
If you notice that the saddle stitch position of the paper is not exactly in the middle of the booklet, you can make adjustments to the saddle stitch position to compensate for this error. Adjust the folding position of the paper and the saddle stitch position at the same time. Adjusting the Saddle Stitch Position
Item
Setting Description
DeviceAdmin
NetworkAdmin
Can be set in Remote UI
Device Information Delivery Available
Import All Function
Name of Item When Exporting with the Remote UI
<Change Fold/Stitch Position>
-2.00 mm to 0.00 mm to +2.00 mm (in 0.25 mm increments)
Yes
Yes
No
No
No
-

<Adjust Saddle Stitch Fold Position> *

 (Settings/Registration)  <Adjustment/Maintenance>  <Adjust Action>
If you notice that the folds of the paper are not exactly in the middle of the booklet, you can make adjustments to the fold placement to compensate for this error. This mode enables you to adjust the folding position without changing the stapling position. Adjusting the Saddle Stitch Folding Position
Item
Setting Description
DeviceAdmin
NetworkAdmin
Can be set in Remote UI
Device Information Delivery Available
Import All Function
Name of Item When Exporting with the Remote UI
<Adjust Saddle Stitch Fold Position>
-2.00 mm to 0.00 mm to +2.00 mm (in 0.25 mm increments)
Yes
Yes
No
No
No
-

<Adjust Double Staple Width> (8700 Series Only) *

 (Settings/Registration)  <Adjustment/Maintenance>  <Adjust Action>
You can adjust the double staple width.
Item
Setting Description
DeviceAdmin
NetworkAdmin
Can be set in Remote UI
Device Information Delivery Available
Import All Function
Name of Item When Exporting with the Remote UI
<Adjust Double Staple Width>
When the Staple Finisher-X / Booklet Finisher-X is attached:
<120 mm>, <145 mm>
When the Staple Finisher-W PRO / Booklet Finisher-W PRO is attached:
120 mm to 150 mm (in 1 mm increments)
Yes
Yes
No
No
No
-
When the paper width is smaller than 257 mm, double staple width is fixed <120 mm>.
When the Staple Finisher-W PRO or Booklet Finisher-W PRO is attached: valid only when the Offset mode is not set. The mode is set to <120 mm> when used with the Offset mode.
When the Staple Finisher-X or Booklet Finisher-X is attached: the productivity of the machine may be slightly reduced if this mode is set to <120 mm>.

<Switch Finisher Puncher Mode> *

 (Settings/Registration)  <Adjustment/Maintenance>  <Adjust Action>
You can set whether to give priority to the punching speed or to precision.
Item
Setting Description
DeviceAdmin
NetworkAdmin
Can be set in Remote UI
Device Information Delivery Available
Import All Function
Name of Item When Exporting with the Remote UI
<Switch Finisher Puncher Mode>
<Speed Priority>, <Precision Priority>
Yes
Yes
No
No
B
-

<Speed/Precision Priority for Double Staple> (8700 Series Only) *

 (Settings/Registration)  <Adjustment/Maintenance>  <Adjust Action>
You can set whether to give priority to the double stapling speed or to precision.
Item
Setting Description
DeviceAdmin
NetworkAdmin
Can be set in Remote UI
Device Information Delivery Available
Import All Function
Name of Item When Exporting with the Remote UI
<Speed/Precision Priority for Double Staple>
<Speed Priority>, <Precision Priority>
Yes
Yes
No
No
B
Settings/Registration Basic Information
This mode is enabled only when using the following paper:
Paper size: The width for the feeding direction is 215.9 mm or less
Paper type: Plain, Heavy 1, Color, Pre-punched
Paper weight: 64 g/m2 to 128 g/m2
If you select <Speed Priority>, stapled output paper may not be aligned due to the temperature, humidity, or characteristics of the paper type.

<Adjust Trim Width> (8700 Series Only) *

 (Settings/Registration)  <Adjustment/Maintenance>  <Adjust Action>
You can adjust the trim width of saddle stitched printouts in 0.1 mm increments. Adjusting the Trimming Width (8700 Series Only)
Item
Setting Description
DeviceAdmin
NetworkAdmin
Can be set in Remote UI
Device Information Delivery Available
Import All Function
Name of Item When Exporting with the Remote UI
<Adjust Trim Width>
When the Inner Booklet Trimmer-A is attached to the Booklet Finisher-X:
2.0 mm to 20.0 mm (in 0.1 mm increments)
When the Booklet Trimmer-F is attached to the Booklet Finisher-W PRO:
2.0 mm to 28.0 mm (in 0.1 mm increments)
Yes
Yes
No
No
No
-

<Adjust Fold Position> *

 (Settings/Registration)  <Adjustment/Maintenance>  <Adjust Action>
You can adjust the paper folding position. Adjusting the Paper Folding Position
8700 Series (without paper folding unit) / 6700 Series (without paper folding unit) / 4700 Series only
Item
Setting Description
DeviceAdmin
NetworkAdmin
Can be set in Remote UI
Device Information Delivery Available
Import All Function
Name of Item When Exporting with the Remote UI
<Adjust Fold Position>
-2.00 mm to 0.00 mm to +2.00 mm (in 0.25 mm increments)
Yes
Yes
No
No
No
-
 
8700 Series (with paper folding unit) / 6700 Series (with paper folding unit) only
Item
Setting Description
DeviceAdmin
NetworkAdmin
Can be set in Remote UI
Device Information Delivery Available
Import All Function
Name of Item When Exporting with the Remote UI
<Adjust Fold Position>
<Adjust Z-Fold Position>
-2.0 mm to 0.0 mm to +1.5 mm (in 0.5 mm increments)
Yes
Yes
No
No
No
-
<Adjust C-Fold Position>
(8700 Series Only)
-7.0 mm to -1.0 mm to +5.0 mm (in 0.5 mm increments)
Yes
Yes
No
No
No
-
<Adjust C-Fold Position>
(6700 Series Only)
<A>:
0.0 mm to 6.0 mm (in 0.5 mm increments)
<B>:
0.0 mm to 6.0 mm (in 0.5 mm increments)
Yes
Yes
No
No
No
-
<Adjust Accordion Z-Fold Position>
(8700 Series Only)
-7.0 mm to -1.0 mm to +5.0 mm (in 0.5 mm increments)
Yes
Yes
No
No
No
-
<Adjust Double Parallel Fold Position>
(8700 Series Only)
<A>:
-2.0 mm to -1.0 mm to +5.0 mm (in 0.5 mm increments)
<B>:
0.0 mm to 1.0 mm to +5.0 mm (in 0.5 mm increments)
Yes
Yes
No
No
No
-
<Adjust Half Fold Position>
(8700 Series Only)
-2.0 mm to 0.0 mm to +2.0 mm (in 0.5 mm increments)
Yes
Yes
No
No
No
-
<Adjust Saddle Fold Position>
(8700 Series Only)
When the Booklet Finisher-W PRO is attached:
-8.50 mm to 0.00 mm to +8.50 mm (in 0.25 mm increments)
When the Booklet Finisher-X is attached:
-2.00 mm to 0.00 mm to +2.00 mm (in 0.25 mm increments)
When the Booklet Finisher-AC is attached:
-2.00 mm to 0.00 mm to +2.00 mm (in 0.25 mm increments)
Yes
Yes
No
No
No
-
<Adjust Saddle Fold Position>
(6700 Series Only)
 -2.00 mm to 0.00 mm to +2.00 mm (in 0.25 mm increments)
Yes
Yes
No
No
No
-

<Alignment Adjustment When Stapling> (8700 Series Only) *

 (Settings/Registration)  <Adjustment/Maintenance>  <Adjust Action>
The copied or printed paper may shrink because of temperature, humidity, or a characteristic of the paper type. In this case, this mode enables you to align copied or printed papers by adjusting the position of the alignment guide inside the finisher so as to staple the aligned papers.
Item
Setting Description
DeviceAdmin
NetworkAdmin
Can be set in Remote UI
Device Information Delivery Available
Import All Function
Name of Item When Exporting with the Remote UI
<Alignment Adjustment When Stapling>
-3.0 mm to 0.0 mm to +3.0 mm (in 0.1 mm increments)
Yes
Yes
No
No
A
Settings/Registration Basic Information
If the alignment guide's position is too close to the paper, a paper jam or paper crease may occur. Make sure to perform fine adjustment of the alignment guide's position.

<Finisher Tray A Alignment Adjustment> (8700 Series Only) *

 (Settings/Registration)  <Adjustment/Maintenance>  <Adjust Action>
You can adjust paper alignment when outputting to Tray A of a finisher. Adjusting Paper Alignment (8700 Series Only)
Item
Setting Description
DeviceAdmin
NetworkAdmin
Can be set in Remote UI
Device Information Delivery Available
Import All Function
Name of Item When Exporting with the Remote UI
<Finisher Tray A Alignment Adjustment>
-3.0 mm to 0.0 mm to +3.0 mm (in 0.1 mm increments)
Yes
Yes
No
No
A
Settings/Registration Basic Information
You cannot align output paper in the following situations:
when using paper smaller than A5R
when using different size paper together
If you set <Align Output Paper of Diff. Sizes (Diff. Widths)>to <On>, you can align output paper by paper width.
You can switch between positive and negative values by pressing <±>.

<Finisher Tray B Alignment Adjustment> (8700 Series Only) *

 (Settings/Registration)  <Adjustment/Maintenance>  <Adjust Action>
You can adjust paper alignment when outputting to Tray B of a finisher. Adjusting Paper Alignment (8700 Series Only)
Item
Setting Description
DeviceAdmin
NetworkAdmin
Can be set in Remote UI
Device Information Delivery Available
Import All Function
Name of Item When Exporting with the Remote UI
<Finisher Tray B Alignment Adjustment>
-3.0 mm to 0.0 mm to +3.0 mm (in 0.1 mm increments)
Yes
Yes
No
No
A
Settings/Registration Basic Information
You cannot align output paper in the following situations:
when using paper smaller than A5R
when using different size paper together
If you set <Align Output Paper of Diff. Sizes (Diff. Widths)>to <On>, you can align output paper by paper width.
You can switch between positive and negative values by pressing <±>.

<Finisher Output Priority Settings (Heavy 5, 6)> (8700 Series Only) *

 (Settings/Registration)  <Adjustment/Maintenance>  <Adjust Action>
You can give priority to productivity or alignment for the output paper when using <Heavy 5> or <Heavy 6>.
Item
Setting Description
DeviceAdmin
NetworkAdmin
Can be set in Remote UI
Device Information Delivery Available
Import All Function
Name of Item When Exporting with the Remote UI
<Finisher Output Priority Settings (Heavy 5, 6)>
<Productivity Priority>, <Alignment Priority>
Yes
Yes
No
No
No
-

<Finisher Output Priority Settings (Thin)> (8700 Series Only) *

 (Settings/Registration)  <Adjustment/Maintenance>  <Adjust Action>
You can give priority to productivity or alignment for the output paper when using thin paper.
Item
Setting Description
DeviceAdmin
NetworkAdmin
Can be set in Remote UI
Device Information Delivery Available
Import All Function
Name of Item When Exporting with the Remote UI
<Finisher Output Priority Settings (Thin)>
<Productivity Priority>, <Alignment Priority>
Yes
Yes
No
No
No
-
<Alignment Priority> is available only when outputting on Tray B of a finisher.

<Time Until Stapling Starts in Stapler Mode> *

 (Settings/Registration)  <Adjustment/Maintenance>  <Adjust Action>
You can set the time until stapling is performed after inserting paper when using manual stapling.
Item
Setting Description
DeviceAdmin
NetworkAdmin
Can be set in Remote UI
Device Information Delivery Available
Import All Function
Name of Item When Exporting with the Remote UI
<Time Until Stapling Starts in Stapler Mode>
1 to 3 to 5 second
Yes
Yes
No
No
C
Settings/Registration Basic Information

<Start Key Touch Recognition Delay>

 (Settings/Registration)  <Adjustment/Maintenance>  <Adjust Action>
Adjust the touch time required to begin startup processing.
Item
Setting Description
DeviceAdmin
NetworkAdmin
Can be set in Remote UI
Device Information Delivery Available
Import All Function
Name of Item When Exporting with the Remote UI
<Start Key Touch Recognition Delay>
-1 to 0 to +7
No
No
No
No
C
Settings/Registration Basic Information
This setting does not appear on models with an upright control panel.
84LU-0LJ