Collate
The printouts are collated into sets arranged in the page order of the document.
![]() |
If you install the "Puncher Unit-BS," "Puncher Unit-BT" or "Puncher Unit-BU" in the "Staple Finisher-AF" or "Booklet Finisher-AF," you can punch holes in your printouts. If you install the "Booklet Trimmer-G" in the "Booklet Finisher-AF," you can trim the fore edge of saddle stitched output paper for neat output. For detailed information, see the "Booklet Trimmer-G" user's manual. Also, If you install the "Two-Knife Booklet Trimmer-B," you can trim the top/bottom of saddle stitched output paper for neat output. For detailed information, see the "Two-Knife Booklet Trimmer-B" user's manual. If you install the "Multi Function Professional Puncher-C" in the "Booklet Finisher-AF," you can punches several types of holes. For more information on the "Multi Function Professional Puncher-C," see the manual of the "Multi Function Professional Puncher-C." |
![]() | ![]() | |
Booklet Finisher-AF | Staple Finisher-AF |
![]() |
Output Tray A and B align output paper with their two alignment guides. You can adjust the position of these guides. For more information, see Paper Alignment on Finisher Tray A/B. When the "Long Sheet Tray-B" is attached to the multi-purpose tray, attach the extension output tray to the Output Tray A. If the "Finisher Long Sheet Catch Tray-B" (optional) is attached, the Output tray-A is replaced with it. |
![]() | ![]() | |
Booklet Finisher-AF | Staple Finisher-AF |
![]() |
For the procedure to finish with the stapler, see Finishing with the Stapler. |
Feeder | Platen glass | ||
![]() | ![]() |
Feeder | Platen glass | ||
![]() | ![]() |
Feeder | Platen glass | ||
![]() | ![]() |
Feeder | Platen glass | ||
![]() | ![]() |
Feeder | Platen glass | ||
![]() | ![]() |
Feeder | Platen glass | ||
![]() | ![]() |
Feeder | Platen glass | ||
![]() | ![]() |
Feeder | Platen glass | ||
![]() | ![]() |
Feeder | Platen glass | ||
![]() | ![]() |
Feeder | Platen glass | ||
![]() | ![]() |
Feeder | Platen glass | ||
![]() | ![]() |
Feeder | Platen glass | ||
![]() | ![]() |
Feeder | Platen glass | ||
![]() | ![]() |
Feeder | Platen glass | ||
![]() | ![]() |
![]() |
For information on the output, see Caution When Outputting Paper to the Finisher/Stacker. For information on the paper sizes that can be used for Staple, Saddle Stitch, Hole Punch, and Saddle Fold, see Staple Finisher-AF and Booklet Finisher-AF. To replace the staple cartridge of the stapler unit or saddle stitcher unit, see Loading Staples (Optional). For how to clear a paper jam or a staple jam, see Clearing Paper Jams and Clearing Staple Jams (Optional). The maximum number of bindable sheets may not be possible, depending on the paper type. In this case, change the paper type, or reduce the number of sheets to bind. Collate and groupIf you select <Offset> in combination with the collate or group function, each printout group is shifted. The output trays move downward as the output paper stacks accumulate. Once an output tray has reached its stacking limit, subsequent prints are automatically delivered to the next available tray. If all of the available trays have reached their stacking limits, printing stops. Remove all of the output paper from the trays to resume printing. StaplersWhen you are using the Staple mode, do not remove the stack of paper from the output tray during the job. Remove the stack of paper when the job has been completed. If the <Load staples into the stapler unit.> message appears, almost all of the staples have been used. To proceed, replace the staple cartridge. If a tray reaches the lowest position limit, printing stops temporarily. Remove all of the output paper from the tray to resume printing. Saddle stitchThe accuracy of folds may vary depending on the paper type and the number of sheets. |