[PS] Settings

 

NOTE
These settings are applicable only when printing in the PS mode.

[Paper Save]


[On], [Off]*

This setting specifies whether to output a blank page when there is no data to print on the page.

[On]

A blank page is not output, thus saving paper.

[Off]

A blank page is output.
NOTE
Depending on the content of print data, some pages may not be determined as blank even if nothing is drawn on the print area of those pages.

[Job Timeout]


0 to 3600 seconds; 0* seconds

This setting enables you to specify the amount of time before a job times out. If a job has not finished within the set time limit, the job automatically cancels.

[Print PS Errors]


[On], [Off]*

This setting determines whether an error page is printed when an error is encountered.

NOTE
If an error is encountered during printing, regardless of the [Print PS Errors] settings, <NG> appears in the print job log screen.

[Line Refinement]


[On]*, [On (Slim)], [Off]

This setting determines whether to perform the process for unifying the thickness of fine lines.

[Halftones]


[Text]: [Resolution]*, [Gradation], [High Resolution]
[Graphics]: [Resolution]*, [Gradation], [High Resolution]
[Image]: [Resolution]*, [Gradation], [High Resolution]

This setting specifies how to express halftones.
Settings can be applied separately for text, graphics, and image data.

[Resolution]

A dither pattern that gives priority to the resolution of the images is used. This helps eliminate the appearance of jagged or uneven lines along the edges of objects and is best for printing standard text and graphics.

[Gradation]

A dither pattern that gives priority to the appearance of smooth changes in tone is used. This is best for reproducing images with delicate gradations or changes of tone.

[High Resolution]

Finer printing can be done than with [Resolution], although toner stability is somewhat weaker. This is suited to printing small characters and fine lines, and outlines (such as from CAD data) sharply.

[Halftones] (2700 Series)


[Error Diffusion (600dpi Only)]: [On], [Off]*
[Text]: [Resolution]*, [Gradation]
[Graphics]: [Resolution], [Gradation]*
[Image]: [Resolution], [Gradation]*

This setting specifies how to express halftones.
Settings can be applied separately for text, graphics, and image data.

[Error Diffusion (600dpi Only)]

This mode is suitable for printing data with text and thin lines and the curved lines of CAD data, etc.
NOTE
The stability of the texture and fixed toner may be reduced when this mode is used.

[Resolution]

A dither pattern that gives priority to the resolution of the images is used. This helps eliminate the appearance of jagged or uneven lines along the edges of objects and is best for printing standard text and graphics.

[Gradation]

A dither pattern that gives priority to the appearance of smooth changes in tone is used. This is best for reproducing images with delicate gradations or changes of tone.

[Brightness]


85% to 115%; 100%*

This setting adjusts the brightness of the overall image. The settings can be set between 85% and 115% in increments of 5%.
Selecting 85% makes the image brighter, and selecting 115% makes it darker.

NOTE
This mode is only available if you set [Toner Save] to [On].

[Grayscale Conversion]


[sRGB], [NTSC]*, [Uniform RGB]

You can select ways to convert color values to a grayscale value when you print color print data.

[sRGB]

Lets you to calculate the grayscale value by the color conversion method based on sRGB.

[NTSC]

Lets you to calculate the grayscale value by the color conversion method based on NTSC.

[Uniform RGB]

Counts the average value of the Red, Green, and Blue values as the grayscale value.

NOTE
This section describes the settings to convert the color data into grayscale data.
This setting is invalid for black-and-white data.

[Dot Gain Adjustment]


[-10%], [-5%], [Standard]*, [+5%], [+10%]

You can adjust dotted areas to change darkness and lightness of painted areas. A higher number specifies a darker printed area.
8EAU-00U