<Adjust Action>

Specify the settings for adjusting the machine's actions.


For information on the items ("A", "B", "C", and "No") in the "Import All Function" column, see Import All Function. Item marked with an asterisk (*) Only appears if you have the option installed. Checking the Options Installed on This Machine

<Saddle Stitch Staple Repositioning> *

(Settings/Registration)

Feeds papers to the saddle stitcher unit and staples them several times, and performs the saddle stitch staple repositioning procedure. The machine performs this adjustment procedure if stapling has not been performed after you clear a staple jam or replace the staple cartridge.

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Saddle Stitch Staple Repositioning>	<Start>	Yes	Yes	No	No	No	-


Make sure to remove all output booklets from the booklet tray before performing the saddle stitch staple repositioning procedure.


Paper that is required for the saddle stitch staple repositioning procedure is automatically fed to the saddle stitcher unit by the machine. 305 mm x 457 mm, A3, B4, A4R, 11" x 17", LGL, LTRR, or custom paper sizes equivalent to these paper sizes can be used. (Make the paper source to which transparencies are registered unavailable.)

<Change Fold/Stitch Position> *

(Settings/Registration)

If you notice that the saddle stitch position of the paper is not exactly in the middle of the booklet, you can make adjustments to the saddle stitch position to compensate for this error. Adjust the folding position of the paper and the saddle stitch position at the same time. Adjusting the Saddle Stitch Position

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Change Fold/Stitch Position>	-2.00 mm to 0.00 mm to +2.00 mm (in 0.25 mm increments)	Yes	Yes	No	No	No	-

<Adjust Saddle Stitch Fold Position> *

(Settings/Registration)

If you notice that the folds of the paper are not exactly in the middle of the booklet, you can make adjustments to the fold placement to compensate for this error. This mode enables you to adjust the folding position without changing the stapling position. Adjusting the Saddle Stitch Folding Position

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Adjust Saddle Stitch Fold Position>	-2.00 mm to 0.00 mm to +2.00 mm (in 0.25 mm increments)	Yes	Yes	No	No	No	-

<Adjust Double Staple Width> *

(Settings/Registration)

You can adjust the double staple width.

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Adjust Double Staple Width>	<120 mm>, <145 mm>	Yes	Yes	No	No	No	-


When this mode is set to <120 mm>, the productivity of the machine may be slightly reduced.

<Switch Finisher Puncher Mode> *

(Settings/Registration)

You can set whether to give priority to the punching speed or to precision.

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Switch Finisher Puncher Mode>	<Speed Priority>, <Precision Priority>	Yes	Yes	No	No	B	Settings/Registration Basic Information

<Adjust Trim Width> *

(Settings/Registration)

You can adjust the trim width of saddle stitched printouts in 0.1 mm increments. Adjusting the Trimming Width

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Adjust Trim Width>	2.0 mm to 20.0 mm	Yes	Yes	No	No	No	-

<Color/B&W Priority for First Print Time>

(Settings/Registration)

You can set whether priority is given to color or black-and-white printing for the first print time.

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Color/B&W Priority for First Print Time>	<Color Priority>, <Black & White Priority>	No	No	No	No	B	Settings/Registration Basic Information


The settings is only effective after the first job is processed and you have restarted the machine (by turning the main power switch OFF and then ON again). For instructions on restarting (turning the main power switch OFF and then ON) the machine, see Turning ON the Machine.

<Adjust Fold Position> *

(Settings/Registration)

You can adjust the paper folding position. Adjusting the Saddle Stitch Folding Position

Without paper folding unit

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Adjust Fold Position>	-2.00 mm to 0.00 mm to +2.00 mm (in 0.25 mm increments)	Yes	Yes	No	No	No	-

With paper folding unit

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Adjust Fold Position>
<Adjust Z-Fold Position>	-2.0 mm to 0.0 mm to +1.5 mm (in 0.5 mm increments)	Yes	Yes	No	No	No	-
<Adjust C-Fold Position>	When the Paper Folding Unit-K is attached: -7.0 mm to -1.0 mm to +5.0 mm (in 0.5 mm increments) When the Document Insertion / Folding Unit-K is attached: <A>: 0.0 mm to 6.0 mm (in 0.5 mm increments) <B>: 0.0 mm to 3.0 mm (in 0.5 mm increments)	Yes	Yes	No	No	No	-
<Adjust Accordion Z-Fold Position>	-7.0 mm to -1.0 mm to +5.0 mm (in 0.5 mm increments)	Yes	Yes	No	No	No	-
<Adjust Double Parallel Fold Position>	<A>: -2.0 mm to -1.0 mm to +5.0 mm (in 0.5 mm increments) <B>: 0.0 mm to 1.0 mm to +5.0 mm (in 0.5 mm increments)	Yes	Yes	No	No	No	-
<Adjust Half Fold Position>	-2.0 mm to 0.0 mm to +2.0 mm (in 0.5 mm increments)	Yes	Yes	No	No	No	-
<Adjust Saddle Fold Position>	-2.00 mm to 0.00 mm to +2.00 mm (in 0.25 mm increments)	Yes	Yes	No	No	No	-

<Correct Curl for Each Paper Drawer> *

(Settings/Registration)

This mode enables you to adjust the curl correction level of each paper source.

The curl correction level is constantly adjusted to suit the characteristics of the paper. However, if the paper curl is not corrected properly, you can manually adjust the curl correction level to accommodate the environment and the characteristics of the paper, such as moisture in the paper. Curl Correction for Each Paper Drawer

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Correct Curl for Each Paper Drawer>	Face Up Output (Reverse)：-10 to 0 to +10 Face Down Output (Normal)：-10 to 0 to +10	Yes	Yes	No	No	No	-

<Time Until Stapling Starts in Stapler Mode> *

(Settings/Registration)

You can set the time until stapling is performed after inserting paper when using manual stapling.

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Time Until Stapling Starts in Stapler Mode>	1 to 3 to 5 second	Yes	Yes	No	No	C	Settings/Registration Basic Information

<Alignment Adjustment When Stapling> *

(Settings/Registration)

The copied or printed paper may shrink because of temperature, humidity, or a characteristic of the paper type. In this case, this mode enables you to align copied or printed papers by adjusting the position of the alignment guide inside the finisher so as to staple the aligned papers.

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Alignment Adjustment When Stapling>	-3.0 mm to 0.0 mm to +3.0 mm (in 0.1 mm increments)	Yes	Yes	No	No	A	Settings/Registration Basic Information


This mode can be set when the Staple Finisher-AG or Booklet Finisher-AG is attached. If the alignment guide's position is too close to the paper, a paper jam or paper crease may occur. Make sure to perform fine adjustment of the alignment guide's position.

<Finisher Tray A Alignment Adjustment> *

(Settings/Registration)

You can adjust paper alignment when outputting to Tray A of a finisher. Adjusting Paper Alignment

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Finisher Tray A Alignment Adjustment>	-3.0 mm to 0.0 mm to +3.0 mm (in 0.1 mm increments)	Yes	Yes	No	No	A	Settings/Registration Basic Information


You cannot align output paper in the following situations: when using paper smaller than A5R when using different size paper together If you set <Align Output Paper of Diff. Sizes (Diff. Widths)> to <On>, you can align output paper by paper width.


This mode can be set when the Staple Finisher-AG or Booklet Finisher-AG is attached. You can switch between positive and negative values by pressing <±>.

<Finisher Tray B Alignment Adjustment> *

(Settings/Registration)

You can adjust paper alignment when outputting to Tray B of a finisher. Adjusting Paper Alignment

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Finisher Tray B Alignment Adjustment>	-3.0 mm to 0.0 mm to +3.0 mm (in 0.1 mm increments)	Yes	Yes	No	No	A	Settings/Registration Basic Information


You cannot align output paper in the following situations: when using paper smaller than A5R when using different size paper together If you set <Align Output Paper of Diff. Sizes (Diff. Widths)> to <On>, you can align output paper by paper width.


This mode can be set when the Staple Finisher-AG or Booklet Finisher-AG is attached. You can switch between positive and negative values by pressing <±>.

<Finisher Tray C Alignment Adjustment> *

(Settings/Registration)

You can adjust paper alignment when outputting to Tray C of a finisher. Adjusting Paper Alignment

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Finisher Tray C Alignment Adjustment>	-2.0 mm to 0.0 mm to +2.0 mm (in 0.1 mm increments)	Yes	Yes	No	No	A	Settings/Registration Basic Information


You cannot align output paper in the following situations: when using paper smaller than A5R when using different size paper together


This mode can be set when the Staple Finisher-AG, Booklet Finisher-AG or Finisher Jogger Kit-A is attached. You can switch between positive and negative values by pressing <±>.

<Finisher Output Priority Settings (Thin)> *

(Settings/Registration)

You can give priority to productivity or alignment for the output paper when using thin paper.

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Finisher Output Priority Settings (Thin)>	<Productivity Priority>, <Alignment Priority>	Yes	Yes	No	No	No	-


This mode can be set when the Staple Finisher-AG or Booklet Finisher-AG is attached. <Alignment Priority> is available only when outputting on Tray B of a finisher.

<Finisher Output Priority Settings> *

(Settings/Registration)

You can give priority to productivity or alignment for the output paper.

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Finisher Output Priority Settings>	<Productivity Priority>, <Alignment Priority>	Yes	Yes	No	No	No	-


This mode can be set when the Staple Finisher-AG, Booklet Finisher-AG or Finisher Jogger Kit-A is attached.

<Start Key Touch Recognition Delay>

(Settings/Registration)

Adjust the touch time required to begin startup processing.

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Start Key Touch Recognition Delay>	-1 to 0 to +7	No	No	No	No	C	Settings/Registration Basic Information

<Adjust Action>

Item marked with an asterisk (*)

<Saddle Stitch Staple Repositioning> *

<Change Fold/Stitch Position> *

<Adjust Saddle Stitch Fold Position> *

<Adjust Double Staple Width> *

<Switch Finisher Puncher Mode> *

<Adjust Trim Width> *

<Color/B&W Priority for First Print Time>

<Adjust Fold Position> *

<Correct Curl for Each Paper Drawer> *

<Time Until Stapling Starts in Stapler Mode> *

<Alignment Adjustment When Stapling> *

<Finisher Tray A Alignment Adjustment> *

<Finisher Tray B Alignment Adjustment> *

<Finisher Tray C Alignment Adjustment> *

<Finisher Output Priority Settings (Thin)> *

<Finisher Output Priority Settings> *

<Start Key Touch Recognition Delay>