<Adjust Action>

Specify the settings for adjusting the machine's actions.


For information on the items ("A", "B", "C", and "No") in the "Import All Function" column, see Import All Function. Item marked with an asterisk (*) Only appears if you have the option installed. Checking the Options Installed on This Machine

<Saddle Stitch Staple Repositioning> *

(Settings/Registration)

Feeds papers to the saddle stitcher unit and staples them several times, and performs the saddle stitch staple repositioning procedure. The machine performs this adjustment procedure if stapling has not been performed after you clear a staple jam or replace the staple cartridge.

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Saddle Stitch Staple Repositioning>	<Start>	Yes	Yes	No	No	No	-


Make sure to remove all output booklets from the booklet tray before performing the saddle stitch staple repositioning procedure. Make sure to remove the paper that was used for adjustment.


Paper that is required for the saddle stitch staple repositioning procedure is automatically fed to the saddle stitcher unit by the machine. 305 mm x 457 mm, A3, B4, A4R, 11" x 17", LGL, LTRR, or custom paper sizes equivalent to these paper sizes can be used. (Make the paper source to which transparencies are registered unavailable.)

<Adjust Saddle Stitch Fold Position/Stitch Position> *

(Settings/Registration)

Adjust the saddle stitch fold position and staple position so that they are at the center of the paper. Print a test page, check the current state of the fold position and the shift width on the test page, and then perform adjustment. Adjusting the Saddle Stitch Fold Position and Staple Position

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Adjust Saddle Stitch Fold Position/Stitch Position>	Adjust Saddle Stitch Fold Position/Stitch Position	Yes	Yes	No	No	No	-

<Adjust Double Staple Width> (8900 Series Only) *

(Settings/Registration)

You can adjust the double staple width.

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Adjust Double Staple Width>	When the Staple Finisher-X / Booklet Finisher-X is attached: <120 mm>, <145 mm> When the / Booklet Finisher-AG is attached: 120 mm to 150 mm (in 1 mm increments)	Yes	Yes	No	No	No	-


When the paper width is smaller than 257 mm, double staple width is fixed <120 mm>. When the or Booklet Finisher-AG is attached: valid only when the Offset mode is not set. The mode is set to <120 mm> when used with the Offset mode. When the Staple Finisher-X or Booklet Finisher-X is attached: the productivity of the machine may be slightly reduced if this mode is set to <120 mm>.

<Switch Finisher Puncher Mode> (8900 Series / 6900 Series Only) *

(Settings/Registration)

You can set whether to give priority to the punching speed or to precision.

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Switch Finisher Puncher Mode>	<Speed Priority>, <Precision Priority>	Yes	Yes	No	No	B	-

<Speed/Precision Priority for Double Staple> (8900 Series Only) *

(Settings/Registration)

You can set whether to give priority to the double stapling speed or to precision.

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Speed/Precision Priority for Double Staple>	<Speed Priority>, <Precision Priority>	Yes	Yes	No	No	B	Settings/Registration Basic Information


This mode is enabled only when using the following paper: Paper size: The width for the feeding direction is 215.9 mm or less Paper type: Plain, Heavy 1, Color, Pre-punched Paper weight: 64 g/m2 to 128 g/m2 If you select <Speed Priority>, stapled output paper may not be aligned due to the temperature, humidity, or characteristics of the paper type.

<Adjust Trim Width> (8900 Series Only) *

(Settings/Registration)

You can adjust the trim width of saddle stitched printouts in 0.1 mm increments. Adjusting the Trimming Width (8900 Series Only)

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Adjust Trim Width>	When the Inner Booklet Trimmer-A is attached to the Booklet Finisher-X: 2.0 mm to 20.0 mm (in 0.1 mm increments) When the Booklet Trimmer-G is attached to the Booklet Finisher-AG: 2.0 mm to 28.0 mm (in 0.1 mm increments)	Yes	Yes	No	No	No	-

<Adjust Fold Position> *

(Settings/Registration)

You can adjust the paper folding position. Adjusting the Paper Folding Position

8900 Series(without paper folding unit) / 6900 Series (without paper folding unit) / 4900 Series only

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Adjust Fold Position>	<Current State>: <A Is Shorter> <A and B Are Equal> <B Is Shorter> <Shift Width (a)> 0.0 mm to +2.0 mm (in 0.1 mm increments)	Yes	Yes	No	No	No	-

8900 Series(with paper folding unit) / 6900 Series (with paper folding unit) only

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Adjust Fold Position>
<Adjust Z-Fold Position>	-2.0 mm to 0.0 mm to +1.5 mm (in 0.5 mm increments)	Yes	Yes	No	No	No	-
<Adjust C-Fold Position> (8900 Series Only)	-7.0 mm to -1.0 mm to +5.0 mm (in 0.5 mm increments)	Yes	Yes	No	No	No	-
<Adjust C-Fold Position> (6900 Series Only)	<A>: 0.0 mm to 6.0 mm (in 0.5 mm increments) <B>: 0.0 mm to 6.0 mm (in 0.5 mm increments)	Yes	Yes	No	No	No	-
<Adjust Accordion Z-Fold Position> (8900 Series Only)	-7.0 mm to -1.0 mm to +5.0 mm (in 0.5 mm increments)	Yes	Yes	No	No	No	-
<Adjust Double Parallel Fold Position> (8900 Series Only)	<A>: -2.0 mm to -1.0 mm to +5.0 mm (in 0.5 mm increments) <B>: 0.0 mm to 1.0 mm to +5.0 mm (in 0.5 mm increments)	Yes	Yes	No	No	No	-
<Adjust Half Fold Position> (8900 Series Only)	-2.0 mm to 0.0 mm to +2.0 mm (in 0.5 mm increments)	Yes	Yes	No	No	No	-
<Adjust Saddle Fold Position> (8900 Series Only)	<Current State>: <A Is Shorter> <A and B Are Equal> <B Is Shorter> <Shift Width (a)> When the Booklet Finisher-AG is attached: 0.0 mm to +8.5 mm (in 0.1 mm increments) When the Booklet Finisher-X is attached: 0.0 mm to +2.0 mm (in 0.1 mm increments) When the Booklet Finisher-AC is attached: 0.0 mm to +2.0 mm (in 0.1 mm increments)	Yes	Yes	No	No	No	-
<Adjust Saddle Fold Position> (6900 Series Only)	<Current State>: <A Is Shorter> <A and B Are Equal> <B Is Shorter> <Shift Width (a)> 0.0 mm to +2.0 mm (in 0.1 mm increments)	Yes	Yes	No	No	No	-

<Alignment Adjustment When Stapling> (8900 Series Only) *

(Settings/Registration)

The copied or printed paper may shrink because of temperature, humidity, or a characteristic of the paper type. In this case, this mode enables you to align copied or printed papers by adjusting the position of the alignment guide inside the finisher so as to staple the aligned papers.

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Alignment Adjustment When Stapling>	-3.0 mm to 0.0 mm to +3.0 mm (in 0.1 mm increments)	Yes	Yes	No	No	A	Settings/Registration Basic Information


If the alignment guide's position is too close to the paper, a paper jam or paper crease may occur. Make sure to perform fine adjustment of the alignment guide's position.

<Finisher Tray A Alignment Adjustment> (8900 Series Only) *

(Settings/Registration)

You can adjust paper alignment when outputting to Tray A of a finisher. Adjusting Paper Alignment (8900 Series Only)

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Finisher Tray A Alignment Adjustment>	-3.0 mm to 0.0 mm to +3.0 mm (in 0.1 mm increments)	Yes	Yes	No	No	A	Settings/Registration Basic Information


You cannot align output paper in the following situations: when using paper smaller than A5R when using different size paper together If you set <Align Output Paper of Diff. Sizes (Diff. Widths)>to <On>, you can align output paper by paper width.


You can switch between positive and negative values by pressing <±>.

<Finisher Tray B Alignment Adjustment> (8900 Series Only) *

(Settings/Registration)

You can adjust paper alignment when outputting to Tray B of a finisher. Adjusting Paper Alignment (8900 Series Only)

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Finisher Tray B Alignment Adjustment>	-3.0 mm to 0.0 mm to +3.0 mm (in 0.1 mm increments)	Yes	Yes	No	No	A	Settings/Registration Basic Information


You cannot align output paper in the following situations: when using paper smaller than A5R when using different size paper together If you set <Align Output Paper of Diff. Sizes (Diff. Widths)>to <On>, you can align output paper by paper width.


You can switch between positive and negative values by pressing <±>.

<Finisher Output Priority Settings (Heavy 5, 6)> (8900 Series Only) *

(Settings/Registration)

You can give priority to productivity or alignment for the output paper when using <Heavy 5> or <Heavy 6>.

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Finisher Output Priority Settings (Heavy 5, 6)>	<Productivity Priority>, <Alignment Priority>	Yes	Yes	No	No	No	-

<Finisher Output Priority Settings (Thin)> (8900 Series Only) *

(Settings/Registration)

You can give priority to productivity or alignment for the output paper when using thin paper.

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Finisher Output Priority Settings (Thin)>	<Productivity Priority>, <Alignment Priority>	Yes	Yes	No	No	No	-


<Alignment Priority> is available only when outputting on Tray B of a finisher.

<Time Until Stapling Starts in Stapler Mode> *

(Settings/Registration)

You can set the time until stapling is performed after inserting paper when using manual stapling.

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Time Until Stapling Starts in Stapler Mode>	1 to 3 to 5 second	Yes	Yes	No	No	C	Settings/Registration Basic Information

<Start Key Touch Recognition Delay>

(Settings/Registration)

Adjust the touch time required to begin startup processing.

Item	Setting Description	DeviceAdmin	NetworkAdmin	Can be set in Remote UI	Device Information Delivery Available	Import All Function	Name of Item When Exporting with the Remote UI
<Start Key Touch Recognition Delay>	-1 to 0 to +7	No	No	No	No	C	Settings/Registration Basic Information


This setting does not appear on models with an upright control panel.

<Adjust Action>

Item marked with an asterisk (*)

<Saddle Stitch Staple Repositioning> *

<Adjust Saddle Stitch Fold Position/Stitch Position> *

<Adjust Double Staple Width> (8900 Series Only) *

<Switch Finisher Puncher Mode> (8900 Series / 6900 Series Only) *

<Speed/Precision Priority for Double Staple> (8900 Series Only) *

<Adjust Trim Width> (8900 Series Only) *

<Adjust Fold Position> *

<Alignment Adjustment When Stapling> (8900 Series Only) *

<Finisher Tray A Alignment Adjustment> (8900 Series Only) *

<Finisher Tray B Alignment Adjustment> (8900 Series Only) *

<Finisher Output Priority Settings (Heavy 5, 6)> (8900 Series Only) *

<Finisher Output Priority Settings (Thin)> (8900 Series Only) *

<Time Until Stapling Starts in Stapler Mode> *

<Start Key Touch Recognition Delay>