Countermeasures for Each Message
If an error occurs during scanning or printing, or if a problem occurs with the network connection or settings, a message appears on the machine display or the Remote UI screen. For details about each message and solutions to the problems, refer to the messages below. Also, if a six-digit number is displayed when you are logging in, see If a six-digit number is displayed when you are logging in.
23 MEMORY FULL
There is insufficient memory to register overlay forms and external characters, etc.
Cancel printing (Canceling Printing), initialize the printer to increase the free memory, and then try printing again. However, note that initializing the printer will erase all the print data in the memory of the machine. For more details, see Setting the Machine (PS/PCL/UFR II Printer) via the online manual Web site.
Press <Skip Error>, and continue printing. However, the data that could not be registered due to a lack of memory will not be printed.
27 JOB REJECT
The specified emulation does not exist.
Specify emulation that the machine supports. For more details, see Setting the Machine (PS/PCL/UFR II Printer) via the online manual Web site.
Press <Skip Error> to skip the printing that an error occurred for. You can perform the following printing.
33 WORK FULL
Could not print because the dedicated work memory was insufficient.
Cancel printing (Canceling Printing), initialize the printer to increase the free memory, and then try printing again. However, note that initializing the printer will erase all the data in the memory of the machine. For more details, see Setting the Machine (PS/PCL/UFR II Printer) via the online manual Web site.
Press <Skip Error>, and continue printing. However, the data for which an error was displayed will not be printed correctly. Also note that registered data such as overlay forms and macros may be deleted.
52 IMAGEMODE REJECT
Data that cannot be processed was sent while printing an image.
Press <Skip Error> to skip the printing that an error occurred for. However, the data for which an error was displayed will not be printed.
Perform printing again using a printer driver that supports the data format of the image.
The Active Directory site information is invalid. Contact the system manager.
The site information of Active Directory is not set correctly.
Check whether [Timing of Site Information Retrieval:] and [Site Access Range:] are set correctly in [Use of Access Mode within Sites:].
Could not verify CRL.
Could not confirm the CA certificate of the certificate authority that issued the certificate revocation list (CRL).
Register the CA certificate of the certificate authority that issued the certificate revocation list (CRL).
Registering a CA Certificate
Registering a CA Certificate
D1 Replot Buffer Full
Could not redraw because data could not be registered to the replot buffer.
Press <Skip Error>, and continue printing. However, the data that caused the error will not be printed correctly. For information on the replot buffer, see Print.
D1 Div. Print. Bffr Full
Could not perform divided printing because data could not be registered to the buffer for divided printing.
Cancel printing (Canceling Printing), set <Divide Mode> to <No> and <Enlarge/Reduce> to <Auto> in the HP-GL setup menu, specify the output paper size, and perform printing again. However, the data will be enlarged/reduced when printed. For more details, see Print.
Press <Skip Error>, and continue printing. However, the data that could not be registered will not be printed correctly. For information on divided printing, see Print.
D1 Polygon Buffer Full
Could not draw because data could not be registered to the polygon buffer.
Press <Skip Error>, and continue printing. However, the data that could not be registered will not be printed correctly. For information on the polygon buffer, see Print.
D0-nn error (nn is two alphanumeric characters)
The printer stopped operating normally due to an unknown problem.
Restart the machine. Press the power switch to turn the power OFF (Turning OFF the Machine), wait for longer than 10 seconds, and then turn the power ON again (Turning ON the Machine). If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.
Could not send the new PIN via e-mail. Check the settings.
Could not send an e-mail for resetting the PIN.
Check whether an e-mail address is set.
Check the e-mail settings and network settings.
FF FONT FULL
Could not register font information in the font table because there were too many fonts to register.
Cancel printing (Canceling Printing), initialize the printer to increase the free memory, and then try printing again. However, note that initializing the printer will erase all the data in the memory of the machine. For more details, see Setting the Machine (PS/PCL/UFR II Printer) via the online manual Web site.
Press <Skip Error>, and continue printing. However, the data that could not be registered will not be printed correctly.
FM DL SIZE ERROR n (n is a single alphanumeric character)
The printer stopped operating normally due to an unknown problem.
Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.
FM DL SCALE ERROR n (n is a single alphanumeric character)
The printer stopped operating normally due to an unknown problem.
Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.
FM DL FONT MEMORY FULL
The printer stopped operating normally due to an unknown problem.
Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.
FM FILE ACCESS ERROR
The printer stopped operating normally due to an unknown problem.
Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.
FM SC WORK MEM. ERROR n (n is a single alphanumeric character)
The printer stopped operating normally due to an unknown problem.
Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.
FM ALIGNMENT ERROR
The printer stopped operating normally due to an unknown problem.
Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.
FM FONT PARSE ERROR
The printer stopped operating normally due to an unknown problem.
Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.
FM FONT MEMORY FULL
The printer stopped operating normally due to an unknown problem.
Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.
FM WORK MEMORY ERROR
The printer stopped operating normally due to an unknown problem.
Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.
IEEE 802.1X error. Set the correct authentication information.
The client authentication information is not set correctly.
Check whether the authentication method and authentication information (key and certificate, user name and password, and CA certificate) are set correctly.
IEEE 802.1X error. No reply from the destination.
An error occurred while communicating with the authenticator.
Check whether the authenticator (LAN switch) and RADIUS server are set correctly.
IEEE 802.1X error. Cannot analyze the certificate.
Failed to analyze the server certificate sent from the RADIUS server.
Check the content of the server certificate of the RADIUS server.
IEEE 802.1X error. The certificate is incorrect.
An error occurred when using the server certificate sent from the RADIUS server as a CA certificate for validation.
Check the content of the server certificate of the RADIUS server and the CA certificate registered in the machine.
Registering a CA Certificate
Registering a CA Certificate
IEEE 802.1X error. The certificate has expired.
The server certificate sent from the RADIUS server has expired.
Check the expiration date of the server certificate of the RADIUS server.
IEEE 802.1X error. Change the authentication password.
The password has expired.
Set a new password.
IEEE 802.1X error. Check the authentication settings.
The authentication method set in the machine and the authentication method set in the RADIUS server do not match.
Check the authentication method set in the machine and the RADIUS server, and set the correct authentication method.
Set the IP address.
The IP address of the machine is not set.
Set the IP address in <TCP/IP Settings>, and restart the machine.
Setting an IP Address
Setting an IP Address
Cannot register PDF with Format to PDF/A as default. All other settings have been registered.
You tried to register a default value for <Scan and Send>, <Scan and Store>, or <Access Strd. Files>, while the <Format PDF to PDF/A> settings for the <PDF> file format was changed.
You cannot register default settings if you change the <Format PDF to PDF/A> setting for the <PDF> file format. Register default settings after changing settings other than the <Format PDF to PDF/A> setting.
Check the server name in the SMB server settings.
A computer or printer bearing the same name as that of the SMB server is registered on the WINS database.
Do not register a computer or printer bearing the same name as that of the SMB server to <Computer Name/Workgroup Name Settings> under <TCP/IP Settings>.
Making WINS Settings
<Computer Name/Workgroup Name Settings>
Making WINS Settings
<Computer Name/Workgroup Name Settings>
A computer or printer bearing the same name as that of the SMB server is registered on the WINS database.
Do not register a computer or printer bearing the same name as that of the SMB server to <Computer Name/Workgroup Name Settings> under <TCP/IP Settings>.
TLS Error
The WebDAV server does not support TLS encrypted communication.
Set TLS on the WebDAV server side, according to your environment.
The proxy server does not support TLS encrypted communication.
If the WebDAV client connects to the internet via a proxy, set TLS on the proxy server side.
Cannot delete the default key because it is in use by TLS or other settings. Check the settings.
The key and certificate you are trying to delete is being used in TLS encrypted communications.
Set all TLS settings to <Off> to stop TLS encrypted communication.
TCP/IP Error
Could not automatically retrieve the address with DHCP and Auto IP.
If the address cannot be automatically retrieved with DHCP and Auto IP, <IP Address> in <IPv4 Settings> is set to 0.0.0.0. Set the correct IPv4 address. In addition, if you selected <Wired LAN + Wireless LAN> or <Wired LAN + Wired LAN> in <Select Interface>, correctly configure the IPv4 address of the sub line.
Setting an IPv4 Address
<IP Address Settings> (<Sub Line Settings>)
Setting an IPv4 Address
<IP Address Settings> (<Sub Line Settings>)
0.0.0.0 is set as a fixed IPv4 address in <IP Address> in <IPv4 Settings>.
The IPv6 address is not set correctly.
Check the following. It may take several minutes until the stateless address is decided.
Check whether <Use IPv6> is set to <On> in <IPv6 Settings>.
When using a stateless address or DHCPv6, check whether each address has been retrieved.
If the address has not been retrieved, check the settings of the router and the DHCPv6 server.
The address of the DNS server is not set correctly.
Check whether the address of the DNS server is set correctly in <IPv4> or <IPv6>.
Making DNS Settings
Making DNS Settings
Could not send to the TCP/IP protocol stack.
Check whether the IPv4 address or IPv6 address is set correctly in <IPv4 Settings> or <IPv6 Settings>. In addition, if you selected <Wired LAN + Wireless LAN> or <Wired LAN + Wired LAN> in <Select Interface>, correctly configure the IPv4 address of the sub line.
Setting an IPv4 Address
Setting an IPv6 Address
Setting an IPv4 Address
Setting an IPv6 Address
Out of resources. Wait a moment, then try again.
TCP/IP resources were insufficient while continuously sending or after continuously sending with FTP or Windows (SMB).
Try again after waiting a while.
Check the TCP/IP.
The TCP/IP of the machine is not operating.
Check the IP address, DHCP, and Auto IP settings in <TCP/IP Settings>.
Setting an IPv4 Address
Setting an IPv4 Address
If you selected <Wired LAN + Wireless LAN> or <Wired LAN + Wired LAN> in <Select Interface>, check the settings for the IP address and DHCP in <Sub Line Settings>.
<IP Address Settings> (<Sub Line Settings>)
<IP Address Settings> (<Sub Line Settings>)
Check the TCP/IP. (Main Line)
The IP address of the main line is set to "0.0.0.0".
Set a different IP address.
Setting an IPv4 Address
Setting an IPv4 Address
Check the TCP/IP. (Sub Line)
The IP address of the sub line is set to "0.0.0.0".
Set a different IP address.
Setting the IPv4 Address of the Sub Line
Setting the IPv4 Address of the Sub Line
Universal Print: A server communication error occurred.
The machine is not connected to the network correctly.
Check the machine and network settings, and try connecting again.
Could not communicate because a server error occurred.
Check whether the server is operating normally.
Communication with the server is blocked due to firewall settings.
Configure the firewall settings to allow communication.
Universal Print: Could not authenticate with server.
An error has occurred during server authentication.
Restart the machine. If the message still appears after restarting the machine, make a note of the message and contact your dealer or service representative.
Universal Print: The certificate has expired.
The expiration date of the certificate has expired.
Delete this machine from Microsoft Entra ID and the computer, re-register the machine, and then update the certificate.
Universal Print: An internal error occurred.
The printer stopped operating normally due to an unknown problem.
Restart the machine. If the message still appears after restarting the machine, make a note of the message and contact your dealer or service representative.
Universal Print: The printer is not registered.
This machine was deleted from Microsoft Entra ID and could not be communicated with.
Re-register this machine in Microsoft Entra ID.
Check the wired LAN adapter connected to the USB port.
Multiple USB-LAN adapters are connected, or the USB-LAN adapter is not connected/recognized.
Check the connection of the USB-LAN adapter.
Connecting to a Wired LAN for the Sub Line
Connecting to a Wired LAN for the Sub Line
If you reconnected the USB-LAN adapter, restart the machine.
Front Side
Front Side
XPS Print Range Error
There are no pages that can be processed in the specified range for printing.
Specify a correct page range.
XPS Image Data Error
Failed to extend the image data.
Replace the image data in the XPS file and try printing again.
XPS Spool Memory Full
There is insufficient memory to process the XPS data.
Restart the machine and try printing again. If you still cannot print, divide the pages into multiple files and print them separately.
XPS Data Error
An invalid command is specified due to corrupt data, etc. and processing cannot continue.
Perform printing again using XPS data in a format supported by the machine.
XPS Unsupport Image Err
An unsupported data format is included.
Convert the data to the TIFF or JPEG format and try printing again.
XPS Font Error
Failed to analyze the font data.
Replace the font data in the XPS file and try printing again.
XPS Page Data Error
Cannot generate pages because the descriptions are incorrect.
Perform printing again using XPS data in a format supported by the machine.
XPS Memory Full
There is insufficient memory to process the XPS data.
Press <Skip Error>, and continue printing. However, pages that include the data that caused the error may not be printed correctly.
You do not have privileges to access the XXX page.
You tried to log in as a user without the required privileges.
Log in as a user with the required privileges.
The account has expired. Contact the system manager.
The certificate may have expired.
Confirm the expiration date of for the certificate registered in the machine. If the certificate has expired, register a certificate within the validity period.
Registering a Key and Certificate for Network Communication
Registering a Key and Certificate for Network Communication
The expiration date of the account has expired.
Confirm the expiration date of the corresponding account.
Access point connection error. Check Wireless LAN Information.
The access point could not be found.
Check the wireless LAN settings.
Check the settings and information of the wireless LAN
Check the settings and information of the wireless LAN
AP Mode: Ended due to an error.
No data was sent or received between the machine and the connected mobile device for over three minutes.
Check the connection between the machine and the mobile device.
AP Mode: Ended because no other device could be found.
Cannot find a mobile device capable of connection.
Check the network settings of the mobile device, and then connect by holding it near the machine. Depending on your mobile device, the machine may not operate correctly. If you cannot successfully connect, contact your dealer or service representative.
AP Mode: Max no. of devices that can connect has been reached.
Cannot connect because the number of mobile devices which can connect simultaneously has reached the upper limit.
Disconnect any unnecessary mobile devices, or wait until other mobile devices have disconnected.
AP Mode: Connected to other devices.
Cannot connect because the machine is already connected to another device.
Wait until the connection to the other device has terminated.
Prepare a new XXXXX toner cartridge.
Toner in the toner cartridge is running out.
You can continue printing, but at this time you should prepare a new toner cartridge to have it available when needed.
 |
This message may not be displayed depending on your contract. The "XXXX" in the message indicates the toner color. |
Following toner cartridges have reached end of their lifetimes. Replacing the toner cartridges is recommended. Printing can be continued by pressing [Resume Printing], but problems due to using those cartridges are not covered by warranty.
A toner cartridge has reached the end of its lifetime.
It is recommended to replace the toner cartridge. But you may be able to continue printing. In this case, the print quality is not guaranteed.
Procedure for Replacing the Toner Cartridge
Procedure for Replacing the Toner Cartridge
Remaining toner of the following toner cartridges is low. Press [Resume Printing] to continue printing.
A toner cartridge needs to be replaced soon. Make sure that you have a replacement toner cartridge ready.
Replace the toner cartridge if you see this message before you start to print a large job. This message is displayed when <Action When Remaining Toner Is Low> is set to <Display Warning Screen>.
<Action When Remaining Toner Is Low>
<Action When Remaining Toner Is Low>
Could not delete authentication information because an error occurred.
The authentication information could not be deleted because an unknown error occurred.
Contact your dealer or service representative.
Could not set authentication information because an error occurred.
The authentication information could not be set because an unspecified error occurred.
Contact your dealer or service representative.
An error occurred. Contact the system manager.
The selected user has already been deleted.
Log in as the Administrator and register the button again.
An unexpected system error occurred.
Check the operations and log in again. If you still cannot log in, consult your system administrator.
No response.
Could not send because an error occurred in the server.
Check whether the server is operating normally.
The machine is not connected to the network correctly.
Check the machine and network settings, and try connecting again.
Setting up the Network Environment
Setting up the Network Environment
Could not send e-mail or an I-fax because an error occurred in TCP/IP.
Check the machine and network settings, and try connecting again.
Setting up the Network Environment
Setting up the Network Environment
Waste toner container is nearly full. Replacement not yet needed.
The waste toner container is almost full.
You can continue printing for a while, but you should have a new one available so that you can make replacement as soon as it is needed. If you decide to replace the waste toner container at the time when this message is displayed, press the icon at the bottom right of the screen to display a motion video to give the instructions for waste toner container replacement. Follow these instructions to replace the waste toner container.
Replace the waste toner container.
The waste toner container is full, so printing is not possible any longer.
Follow the instructions on the screen to replace the waste toner container.Procedure for Replacing the Waste Toner Container
Cannot recall the settings because the function for the button does not exist.
A personal button or shared button that includes a function not supported by the machine was used.
If you have imported personal buttons/shared buttons registered in another imageRUNNER ADVANCE series device, buttons not supported by the machine may be included. Register the personal buttons/shared buttons again in the machine.
Cannot recall the settings because the function for the button is disabled. Enable the function, then try again.
The operation could not be executed by pressing the button because the function to use has been stopped.
Press the button after enabling the function that was stopped to be used.
Synchronize Custom Settings: Log in again for synchronization.
There is an inconsistency between the synchronization data of the server machine and that of the client machine synchronizing custom settings.
Log out, and then log in again.
Synchronize Custom Settings: Some settings are restricted.
The client machine was synchronizing custom settings, but the server machine is turned OFF or is not operating normally.
Turn the server machine ON.
If the server machine is operating normally, check that its network cable is connected before checking the network settings.
|
Data may not be able to be synchronized correctly while this message is displayed, but can be synchronized after the problem is resolved. |
Synchronize Custom Settings: An error occurred.
An error occurred during synchronization startup.
Confirm that the address of the destination server is correct for the synchronization of custom settings (client).
If the synchronization of custom settings (client) is complete, restart synchronization.
Restart the machine.
If the problem is not resolved even after restarting the machine, check the followings.
1. You can ping the IP address set for the destination
2. The address of the destination server is correctly displayed
Synchronize Custom Settings: Enabling synchronization...
Processing to begin synchronization of custom settings is being performed.
Wait until processing is complete.
Synchronize Custom Settings: Cannot find the server.
The server machine for synchronization of custom settings could not be found using Auto Search.
Confirm that the server machine is turned ON.
If the server machine is operating normally, check that its network cable is connected before checking the network settings.
Confirm the usable conditions for Auto Search. Starting Setting Synchronization
Without using Auto Search, manually specify the server address of the destination for the synchronization of custom settings (client), and the search depth (router).
If the synchronization of custom settings (client) is complete, restart synchronization.
Restart the machine.
Synchronize Custom Settings: Server authentication error.
Authentication with the server machine could not be achieved.
Check that the authentication user ID and new password for the synchronization of custom settings (client) are the same as the authentication user ID and password with administrator privileges in the server machine.
If the synchronization of custom settings (client) is complete, restart synchronization.
Restart the machine.
Synchronize Custom Settings: Cannot identify the server.
Multiple server machines for the synchronization of custom settings were found using Auto Search.
Manually specify the server machine or shut down all unnecessary server machines that are currently running so that only one remains.
When specifying the server machine manually
Without using Auto Search, manually specify the server address of the destination for the synchronization of custom settings (client), and the search depth (router). Starting Setting Synchronization
When shutting down unnecessary servers that are currently running
Even if the network settings of the server machine include both IPv4 and IPv6, if IPv6 is prioritized and the client machine disables IPv6, the client machine cannot connect via search. Enter the IPv4 address for the destination server address.
If the synchronization of custom settings (client) is complete, restart synchronization and then restart the machine.
Check the covers.
The cover of optional equipment is open.
Check whether the covers of optional equipment are closed.
An error occurred when auto exporting the audit log.
The data could not be exported because a server error occurred.
Check that the server is functioning normally.
The machine is not connected to the network correctly.
Check the settings of the machine and the network, and try connecting again.
The automatic export settings are incorrect.
Check that the automatic export settings are correct (Exporting Logs Automatically).
Failed to generate Device Signature Key. Set the e-mail address in Communication Settings.
To use device signatures, you must first configure the e-mail address of the machine.
Configure the e-mail address of the machine (Setting E-mail/I-Fax Communication), and then generate a key for device signatures (Generating a Device Signature Certificate).
The function may be stopped. Buttons could not be imported.
When importing data, buttons with functions not supported by the machine were included.
Check whether all the buttons have been imported to the machine.
Routing registration failed. Check Static Routing Settings.
There is an entry that routing table registration failed for in the static routing settings.
Check the registered destination address and gateway address, and specify the correct settings.
Setting Static Routing
Setting Static Routing
Remove the original from the platen glass.
An original remains on the platen glass.
Remove the original from the platen glass, and place another original.
The original scanning area (feeder) is dirty.
The document feed scanning area (on the feeder side) is dirty.
Clean the document feed scanning area.
Cleaning the Feeder
Cleaning the Feeder
Original scanning area (thin glass strip) is dirty.
The document feed scanning area (the long and thin glass strip) is dirty.
Clean the document feed scanning area.
Cleaning the Feeder
Cleaning the Feeder
Return the originals to their correct order, then press the [Start] key.
Scanning stopped because an unknown problem occurred in the feeder.
Scan the original again from the first page.
Return the originals to their correct order, then press the [Start] key. (The data size of the scanned original exceeds the limit. Settings will be automatically corrected and the originals will be scanned again.)
Scanning was canceled because the data of the scanned document exceeded the maximum size that can be handled by the machine.
Scan the original again from the first page. If you still cannot scan the original, you may be able to scan by lowering the setting in <Sharpness>, and setting <Original Type> to <Text>.
The device is currently being used by another user. Wait a while, and then try to perform the operation again.
You cannot use the machine when it is being used by another user.
Try again after waiting a while.
The number of search results exceeds the limit. Change search conditions, then try again.
Destinations exceeding the maximum number of search results were found.
Narrow the search conditions and try searching again.
Increase the maximum number of search results in <Max Addresses to Search> in <Register LDAP Server>.
Registering the LDAP Server
Registering the LDAP Server
The search condition includes characters that cannot be used with the selected server.
"\" is used in the search conditions.
Remove the "\" from the search conditions and try searching again.
If an uneven number of "(" or ")" are included or an "*" is included inside parentheses, search conditions are not established.
Set a correct combination of characters, and try searching again.
If <LDAP Server Version and Character Code> is set to <ver.2 (JIS)>, only ASCII code (0x20 to 0x7E) characters can be used.
Remove the invalid characters and try searching again.
An error occurred when verifying.
The certificate is invalid.
Register the correct certificate and specify the settings again.
Configuring the Key and Certificate for TLS
Registering a Key and Certificate for Network Communication
Configuring the Key and Certificate for TLS
Registering a Key and Certificate for Network Communication
This CRL is invalid.
The certificate revocation list (CRL) may be corrupt, or a signing algorithm not supported by the machine may be used.
Register the correct certificate revocation list (CRL).
Registering a Certificate Revocation List (CRL)
Registering a Certificate Revocation List (CRL)
This CRL has expired.
The start date for the certificate revocation list (CRL) may be set to a date in the future.
Check the start date of the certificate registered in the machine. If the start date is set to a date in the future, use the certificate on a day after that date.
Registering a Certificate Revocation List (CRL)
Registering a Certificate Revocation List (CRL)
The date and time set on the machine may be incorrect.
Check the date and time setting of the machine.
Setting the Date/Time
Setting the Date/Time
Cannot register because the algorithm of this key is not supported.
You tried to register the key and certificate file of an unsupported encryption algorithm.
Register the key and certificate file of a supported encryption algorithm.
Registering a Key and Certificate
System Specifications
Registering a Key and Certificate
System Specifications
Cannot set as the default key because this key is corrupted or invalid.
The key specified for the machine cannot be set because it is corrupted.
Register the key again.
Registering a Key and Certificate for Network Communication
Registering a Key and Certificate
Registering a Key and Certificate for Network Communication
Registering a Key and Certificate
This certificate has been revoked.
The certificate is included in the certificate revocation list (CRL).
Register a new certificate.
Registering a Key and Certificate for Network Communication
Registering a Key and Certificate for Network Communication
This certificate is invalid.
The certificate is invalid.
Register the correct certificate and specify the settings again.
Configuring the Key and Certificate for TLS
Registering a Key and Certificate for Network Communication
Configuring the Key and Certificate for TLS
Registering a Key and Certificate for Network Communication
This certificate has expired.
The certificate may have expired.
Check the expiration date of the certificate registered in the machine. If the certificate has expired, register a valid certificate.
Registering a Key and Certificate for Network Communication
Registering a Key and Certificate for Network Communication
The date and time set on the machine may be incorrect.
Check the date and time setting of the machine.
Setting the Date/Time
Setting the Date/Time
No response from the server. Check the settings.
The specified server may have a problem such as not being specified correctly, not being turned on, or having insufficient resources.
Try specifying the server again after waiting a while. If there is still no response from the server, select another server.
Cannot start searching because the server version settings are incorrect. Check the settings.
A different server LDAP version is set in the LDAP server and the machine.
Change the setting in <LDAP Server Version and Character Code> in <Register LDAP Server> to "ver.2" to match the LDAP server.
Registering the LDAP Server
Registering the LDAP Server
Check the server.
You tried to access the server without using a proxy.
Check whether the WebDAV server settings are correct.
Check whether the proxy settings are correct.
Setting a Proxy
Setting a Proxy
Access to the destination is not allowed.
Check whether the WebDAV server settings are correct.
You tried to access the server via a proxy without using TLS encrypted communication.
Set <Use Divided Chunk Send for WebDAV TX> to <Off>.
<Use Divided Chunk Send for WebDAV TX>
<Use Divided Chunk Send for WebDAV TX>
The proxy server failed to communicate with an upstream server.
Check whether the WebDAV server and proxy server settings are correct.
An HTTP protocol version not supported by the WebDAV server was used in a request from the WebDAV client.
Check whether the WebDAV server settings are correct.
The disk space of the WebDAV server is insufficient for the request from the WebDAV client.
Make sufficient disk space for the request available on the WebDAV server.
The appropriate paper size, A4, is not available.
Paper of the optimal size selected with Automatic Paper Selection has not been loaded.
Load paper of the displayed size.
<Paper Source Auto Selection> is set to <Off>.
Specify the paper drawer manually.
Set a paper source loaded with the optimal paper size to <On> in <Paper Source Auto Selection>.
<Paper Source Auto Selection>
<Paper Source Auto Selection>
Paper of a type that cannot be selected with Automatic Paper Selection is loaded.
Specify the paper drawer manually.
If you are copying, select the <Consider Paper Type> check box in <Paper Source Auto Selection>.
<Paper Source Auto Selection>
<Paper Source Auto Selection>
Sub line was disconnected due to a subnet mask conflict.
The network addresses of the main line and sub line conflict.
Check the IP address and subnet mask settings of the main line and sub line.
Setting an IP Address
Setting an IP Address
There are too many subdirectories.
The maximum number of characters was exceeded because the number of levels was too deep.
The destination cannot be specified. Specify another destination.
Remove all the output paper.
Paper has accumulated in the output tray.
Remove all paper from the output tray.
The contents of the specified file may be incorrect.
You tried to register a button by specifying a different file when importing.
Register the correct file and try importing again.
The default key is not set. Check TLS Settings.
The key and certificate (TLS server certificate) are not registered.
To use TLS encrypted communication, first register the key to be used.
Configuring the Key and Certificate for TLS
Configuring the Key and Certificate for TLS
The default key is not set. Check the Key and Certificate List settings in Certificate Settings.
The key and certificate (TLS server certificate) are not registered.
Register a key and certificate for performing TLS encrypted communication.
Generating the Key and Certificate for Network Communication
Registering a Key and Certificate
Generating the Key and Certificate for Network Communication
Registering a Key and Certificate
The combination of the allowed version and selected algorithm is inappropriate. Enter settings again.
The selected settings cannot be used together.
Set a valid combination.
Configuring the Key and Certificate for TLS
Configuring the Key and Certificate for TLS
A wired LAN adapter that cannot be used has been connected.
A USB-LAN adapter that cannot be used with the machine is connected.
For information on the USB-LAN adapters that can be used, contact your dealer or service representative.
Connecting to a Wired LAN for the Sub Line
Connecting to a Wired LAN for the Sub Line
Could not verify the certificate.
The CA certificate of a certificate authority could not be confirmed.
Register a CA certificate issued by a certificate authority.
Could not perform the job because the scanned originals were all blank pages.
The scanned document was determined to contain blank pages only.
If the document does not contain blank pages only, check the setting for skipping blank pages.
Skipping Blank Pages When Printing
Skipping Blank Pages When Printing
Cannot connect.
Failed to perform proxy authentication.
Check whether the proxy settings are correct.
Setting a Proxy
Setting a Proxy
Cannot edit/delete the paper because it is being used for other settings in Settings/Registration.
You tried to edit or delete paper that was registered in another setting via <Paper Type Management Settings>.
The paper is registered as "Favorite Paper" in <Register Favorite Paper (Multi-Purpose Tray)> and <Multi-Purpose Tray Defaults>. Cancel the registration.
Registering Frequently Used Paper Size and Type for the Multi-purpose Tray
Registering Frequently Used Paper Size and Type for the Multi-purpose Tray
The paper is set as a target for automatic gradation adjustment. To edit or delete paper via <Paper Type Management Settings>, it is necessary to set another type of paper as a target for correction and perform gradation correction again.
Adjusting Gradation
Adjusting Gradation
Check Computer Name in Settings/Registration.
A computer or printer with the same name is registered in the WINS database.
When <WINS Resolution> in <WINS Settings> is set to <On>, do not register a computer or printer with a name already listed in <Computer Name/Workgroup Name Settings> in <TCP/IP Settings>.
Making WINS Settings
<Computer Name/Workgroup Name Settings>
Making WINS Settings
<Computer Name/Workgroup Name Settings>
A printer or computer with the same name already exists in the same workgroup as this machine.
Do not register a computer or printer with a name already listed in <Computer Name/Workgroup Name Settings> in <TCP/IP Settings>.
<Computer Name/Workgroup Name Settings>
<Computer Name/Workgroup Name Settings>
A toner cartridge of the wrong color may have been inserted. If this toner cartridge is used, a malfunction may occur. Check the inserted toner cartridge.
The color of one of the inserted toner cartridges may be incorrect.
Make sure to check the status of the inserted toner cartridge.
To continue using the toner cartridge, press <I Agree>. If you select this option, the operation of the machine is not guaranteed.
To replace the toner cartridge, press <Cancel>.
If you are not sure about the remedies, contact your dealer or service representative from which you purchased the toner cartridge.
Cannot change the settings because the selected key is being used.
The key and certificate you are trying to delete is being used in TLS encrypted communications.
Set all TLS settings to <Off> to stop TLS encrypted communication.
Cannot find the selected server. Check the settings.
The host name cannot be identified when the authentication information of the LDAP server is set to <Use (Security Authentication)>.
Check whether the settings in <DNS Settings> are correct.
<DNS Settings>
<DNS Settings>
Check whether the settings on the DNS server side are correct.
The IP address could not be identified.
Check whether the settings in <DNS Settings> are correct.
<DNS Settings>
<DNS Settings>
Check whether the settings on the DNS server side are correct.
Cannot connect to the selected server. Check the settings.
Could not connect to the IP address/port.
Check whether the server address and port number in <Register LDAP Server> are correct.
Registering the LDAP Server
Registering the LDAP Server
Check whether the LDAP server is operating normally.
If <Authentication Information> is set to <Use (Security Authentication)> for the LDAP server, check whether UDP packets are blocked by the filter.
Check whether the gateway address set in <TCP/IP Settings> is correct.
Setting an IPv4 Address
Setting an IPv4 Address
The setting item specified from Settings Menu cannot currently be used. Contact the system manager.
The selected settings menu cannot be changed or is not available.
Contact your system administrator.
The selected button may be unavailable. Contact the system manager.
The selected user does not exist.
Log in as the Administrator and register the button again.
"Administrator" has been disabled.
Select a user with administrator privileges.
Could not send.
The data to send is too large.
Reduce the size of the data and try sending again.
Session timed out. Wait a moment, then try to access the database again.
The session timed out because the specified length of time elapsed.
Try accessing again after waiting a while. If the session continues to time out, restart the machine.
Cannot complete searching due to timeout. Check the settings.
The search could not be completed within the specified time.
Increase the length of the timeout time in <Search Timeout> in <Register LDAP Server>.
Registering the LDAP Server
Registering the LDAP Server
Could not execute because the file contains unsupported data.
The page cannot be generated due to incorrect content.
Try printing again using data in a format compatible with the machine.
Direct Connection: Ended due to an error.
Failed to connect to the mobile device, or no data was sent or received between the machine and the connected mobile device for a certain period of time.
Check the connection between the machine and the mobile device.
Direct Connection: Ended because no other dev. could be found.
Cannot find a mobile device capable of connection.
Check the network settings of the mobile device, and then connect by holding it near the machine. Depending on your mobile device, the machine may not operate correctly. If you cannot successfully connect, contact your dealer or service representative.
A non-Canon toner cartridge may be inserted, so information about remaining toner cannot be detected properly.
A toner cartridge for which the print quality cannot be guaranteed may be installed.
To continue using the toner cartridge, press <I Agree>. If you select this option, the operation of the machine is not guaranteed.
A non-Canon or counterfeit toner cartridge may be inserted, so information about remaining toner cannot be detected properly.
A toner cartridge for which the print quality cannot be guaranteed may be installed.
It is recommended to replace the toner cartridge.
Adjusting gradation... Wait a moment.
The machine is performing auto adjustment.
Printing will automatically resume when the adjustment is complete. Wait a while.
Could not access the database. Restart the device.
Failed to access the user database because it is corrupt, etc.
Restart the machine.
Digital Sig. Cert. Access Error
Could not access the device certificate when sending the device signature.
Check the content of the device certificate registered in the machine.
Generating a Device Signature Certificate
Generating a Device Signature Certificate
Certificate Expiration Date Error
The certificate has expired.
Check the expiration date of the certificate.
Cannot log in because multiple users are registered under the same user name. Contact the system manager.
The user name could not be distinguished because user names are set to be not case-sensitive.
Change the settings to make user names case-sensitive, or register another user name.
Cannot register any new buttons because the number of registered buttons has reached the limit. Buttons already registered can be overwritten.
The button cannot be registered because the maximum number of buttons has been exceeded.
Overwrite an existing button or delete unnecessary buttons.
Customizing the <Home> Screen
Customizing the <Home> Screen
Cannot import because the number of buttons for registration has exceeded the upper limit.
Buttons cannot be registered while importing because the maximum number of personal buttons/shared buttons has been exceeded.
Delete unnecessary personal buttons/shared buttons, and import the data again.
Could not register because the number of registered users has reached the limit.
Cannot register the user because the number of users has exceeded the upper limit.
Delete any unnecessary users.
Replace the toner cartridge. (XXXX)
The toner in the toner cartridge has run out.
Pressing the icon displayed at the bottom right of the screen displays a motion video to give the instructions for toner cartridge replacement. Follow these instructions to replace the toner cartridge.
|
The "XXXX" in the message indicates the toner color. When black toner has run out completely, it is not necessary to press the icon on the lower-right corner of the screen. The toner cartridge replacement screen is automatically displayed, which allows you to perform the replacement procedure in accordance with the instructions given by motion video. |
Cannot recognize the inserted toner cartridge. A non-Canon toner cartridge may be inserted, so information about remaining toner cannot be detected properly.
A toner cartridge for which the print quality cannot be guaranteed may be installed.
To continue using the toner cartridge, press <I Agree>. If you select this option, the operation of the machine is not guaranteed.
Cannot recognize the inserted toner cartridge. A non-Canon or counterfeit toner cartridge may be inserted, so printing is currently unavailable.
A toner cartridge for which the print quality cannot be guaranteed may be installed.
It is recommended to replace the toner cartridge.
Cannot recognize the toner cartridge. Pull out the toner cartridge, then insert it again or information about remaining toner won't be detected properly.
The toner cartridge may not be correctly inserted, the toner cartridge may have been damaged, or a toner cartridge with the wrong model number may be inserted.
Reinsert the toner cartridge. Make sure to check the status of the inserted container. For instructions on checking the model number of the toner cartridge, see Consumables.
To continue using the toner cartridge, press <Close> or <I Agree>. If you select this option, the operation of the machine is not guaranteed.
To replace the toner cartridge, press <Cancel>.
If you are not sure about the remedies, contact your dealer or service representative from which you purchased the toner cartridge.
The entered PIN is incorrect.
An incorrect PIN was entered.
Enter the PIN again.
If you do not know the correct PIN, contact the administrator.
The authentication server is not running. Contact the system manager.
The LAN cable is disconnected.
Connect the LAN cable.
The Active Directory server is not running.
Start the Active Directory server.
The KDC service of Active Directory is stopped.
Follow the procedure below to check the status of the service.
1. Start the "Service" management tool of Active Directory.
2. Check whether the Active Directory server is operating normally.
Communication with the Active Directory*server is blocked by the firewall.
Stop blocking the default port 88.
* If Active Directory is set as the login destination, communication is normally performed with the UDP protocol using port 88, but the data may be processed with the TCP protocol if it exceeds a certain size.
Cannot find the authentication server. Contact the system manager.
The LAN cable is disconnected.
Connect the LAN cable.
The primary/secondary DNS server settings of the machine are incorrect or not set.
Check and adjust the DNS server settings of the machine.
The DNS server specified in the machine is not running or its service is stopped.
Follow the procedure below to check the status and settings of the DNS server.
1. Check whether the DNS server specified in the machine is running.
2. Start the "Service" management tool of the DNS server.
3. Check the status in [DNS Server], and if [Enable] is not displayed, right-click and select [Enable].
Check whether the host record exists in the DNS server.
Check whether a host record exists in the DNS server, and whether the forwarder settings are correct.
No password is set on the authentication server side. Contact the system manager.
An appropriate password was not set on the server side when configuring or upgrading Active Directory.
Reset the password of the corresponding account, and specify the settings again.
Cannot log in because anonymous access to the authentication server is not allowed. Contact the system manager.
Anonymous access is not allowed on the LDAP server.
On the information input screen of the LDAP server, select <Use authentication information>, and then specify the user name and password according to what is registered in the LDAP server.
Registering Server Information
Registering Server Information
The account information necessary to log in to the authentication server is invalid. Contact the system manager.
The user name or password is not set correctly.
Confirm the authentication user ID and password, and whether the user has administrator privileges.
The attributes specified in the server settings are not set correctly.
Confirm that the attributes are correct. Also, make sure that the fields (attribute names) do not contain invalid values.
Registering Server Information
Registering Server Information
The administrator account information specified in the server settings is not set correctly. Alternatively, the user could not log in as an administrator.
Specify the correct administrator account information.
The information for the server settings is insufficient.
Confirm that the attributes necessary for logging in are set correctly.
Registering Server Information
Registering Server Information
A competing IP address was found on the network.
The IPv4 address set for the machine already exists in the same network as the machine.
Change the IP address of the machine in <IP Address> in <IPv4 Settings> so that it does not conflict with the IP address of another device.
Setting an IPv4 Address
Setting an IPv4 Address
An IP address conflict was detected on the network (Main Line).
The IPv4 address set for the main line of the machine already exists on the same network as the machine.
Change the IP address of the main line of the machine so that it does not conflict with the IP address of another device.
Setting an IPv4 Address
Setting an IPv4 Address
An IP address conflict was detected on the network (Sub Line).
The IPv4 address set for the sub line of the machine already exists on the same network as the machine.
Change the IP address of the sub line of the machine so that it does not conflict with the IP address of another device.
Setting the IPv4 Address of the Sub Line
Setting the IPv4 Address of the Sub Line
Could not perform the operation because a network error occurred.
Writing from an external source is not allowed.
Set <Prohibit Writing from External> for the destination to <Off>.
The full path (the folder name indicating the filename and destination to save) is too long.
Shorten the folder name or file name or change the destination to save so that the number of characters for the path is 256 characters or fewer, including "/share" or "users".
Check the network connection.
The cable is not connected to the machine correctly.
Check whether the LAN cable is connected correctly. If you had to connect it again, restart the machine.
Connecting to a Wired LAN
Connecting to a Wired LAN
The machine is not connected to the network.
If you want to use the machine without connecting to a network, set <Confirm Network Connection Setting Changes> to <Off>.
<Confirm Network Connection Setting Changes>
<Confirm Network Connection Setting Changes>
Check the network connection. (Main Line)
The machine and the LAN cable of the main line are not connected correctly.
Check whether the LAN cable is connected correctly. If you had to connect it again, restart the machine.
Connecting to a Wired LAN
Connecting to a Wired LAN
The machine is not connected to the network.
If you want to use the machine without connecting to a network, set <Confirm Network Connection Setting Changes> to <Off>.
<Confirm Network Connection Setting Changes>
<Confirm Network Connection Setting Changes>
Check the network connection. (Sub Line)
The machine and the LAN cable of the sub line are not connected correctly.
Check whether the LAN cable is connected correctly. If you had to connect it again, restart the machine.
Front Side
Front Side
The machine is not connected to the network.
If you want to use the machine without connecting to a network, set <Confirm Network Connection Setting Changes> to <Off>.
<Confirm Network Connection Setting Changes>
<Confirm Network Connection Setting Changes>
Scanning was canceled because the originals were not correctly fed.
A paper jam occurred in the feeder because multiple originals were fed together.
Remove the originals from the feeder, and place them again.
A paper jam occurred in the feeder because an invalid type of original was fed.
Remove the invalid original (Placing Originals), and place an appropriate type of original.
Remove the jammed originals from the feeder and any originals left in the feeder tray, then place them back in the feeder tray and press the [Start] key.
Scanning was canceled because the original is jammed in the feeder.
You need to restart the scanning with the sheet jammed in the feeder. Put together the unscanned sheets of original neatly, reload them in the feeder, and then press 
(Start).
(Start).Remove the original from the feeder.
You are using a function that cannot be used when an original is placed in the feeder.
Place the original on the platen glass.
Performing multiple jobs...
Multiple jobs such as print and send jobs are executing at the same time as the scan operation.
Wait a while until the scan operation resumes.
Cannot log in because an authentication error occurred in Department ID Management. Contact the system manager.
When using User Authentication, Department ID Management is enabled but Department IDs have not been assigned to users.
If you are a general user, ask your administrator to assign you a Department ID.
If you are an administrator user, ask the Department ID Management administrator to assign you a Department ID. If no administrator users can log in, contact your dealer or service representative.
PDL Invalid DLG Input
The printer stopped operating normally due to an unknown problem.
Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.
PDL DLG Rendering Error
The printer stopped operating normally due to an unknown problem.
Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.
PDL DLG Unknown Error
The printer stopped operating normally due to an unknown problem.
Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.
PDL DLG Memory Full
The work memory was insufficient when the system was processing data (in particular, graphic processing and text processing).
Press <Skip Error>, and continue printing. However, pages that include the data that caused the error may not be printed correctly.
PDL DLG Mem. Alloc. Err
The printer stopped operating normally due to an unknown problem.
Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.
PDL GL Orig. Pt Unknown
The printer stopped operating normally due to an unknown problem.
Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.
PDL GL Coord.Result
The printer stopped operating normally due to an unknown problem.
Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.
PDL Invalid GL Input
The printer stopped operating normally due to an unknown problem.
Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.
PDL GL Range Check
The printer stopped operating normally due to an unknown problem.
Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.
PDL GL Memory Full
The work memory was insufficient when the system was processing data (in particular, graphic processing and text processing).
Press <Skip Error>, and continue printing. However, pages that include the data that caused the error may not be printed correctly.
PDL GL Mem. Alloc. Err
The printer stopped operating normally due to an unknown problem.
Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.
PDL IMG Refer. Data Err
The TIFF or JPEG data includes data that cannot be processed with the machine.
Cancel printing (Canceling Printing), initialize the printer to increase the free memory, and then try printing again. However, note that initializing the printer will erase all the data in the memory of the machine. For more details, see Setting the Machine (PS/PCL/UFR II Printer) via the online manual Web site.
PDL IMG Initial. Err
The memory for printing the TIFF or JPEG data was insufficient.
Cancel printing (Canceling Printing), initialize the printer to increase the free memory, and then try printing again. However, note that initializing the printer will erase all the data in the memory of the machine. For more details, see Setting the Machine (PS/PCL/UFR II Printer) via the online manual Web site.
PDL IMG Process. Error
An unknown problem occurred while processing the TIFF or JPEG data.
Cancel printing (Canceling Printing), initialize the printer, and try printing again. However, note that initializing the printer will erase all the data in the memory of the machine. For more details, see Setting the Machine (PS/PCL/UFR II Printer) via the online manual Web site.
PDL IMG Invalid Data
The TIFF or JPEG data includes data that cannot be processed with the machine.
Cancel printing (Canceling Printing), and check the TIFF or JPEG data.
Press <Skip Error>, and continue printing. However, the data that caused the error will not be printed.
Data that cannot be processed by the machine because the machine has the same IP address as another device, etc. was sent.
Cancel printing (Canceling Printing), check the IP address in <TCP/IP Settings>, and change the IP address if necessary.
Setting an IP Address
Setting an IP Address
PDL IMG Work Memory Full
The memory for processing the TIFF or JPEG data was insufficient.
Cancel printing (Canceling Printing), initialize the printer to increase the free memory, and then try printing again. However, note that initializing the printer will erase all the data in the memory of the machine. For more details, see Setting the Machine (PS/PCL/UFR II Printer) via the online manual Web site.
Press <Skip Error>, and continue printing. However, the data that caused the error will not be printed.
PDL nn Rendering Error (nn is the module name)
The printer stopped operating normally due to an unknown problem.
Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.
PDL PDF Error
PDF data that cannot be processed with the machine was sent.
Cancel printing (Canceling Printing), optimize the PDF using Adobe Acrobat, and try printing again.
Cancel printing (Canceling Printing), open the PDF file in an application, and try printing again using the printer driver.
If the above-mentioned remedies do not solve the problem, make a note of the message and contact your dealer or service representative.
PDL PDF Data Decode Err
The password for printing the PDF file is incorrect.
Enter the correct password, and try printing again.
Printing is not allowed in the security settings of the PDF file.
Change the PDF file to allow printing in an application for editing PDF files.
If the PDF file is linked with a policy server, the policy server cannot be accessed.
Check whether the policy server is turned on.
Check whether the machine, policy server, and network are operating normally.
PDL PDF Memory Full
There is insufficient memory to process the PDF data.
Cancel printing (Canceling Printing), optimize the PDF by adjusting settings such as the image resolution using Adobe Acrobat (to reduce the size of the data to print at one time), and perform printing again.
Cancel printing (Canceling Printing), divide the pages of the PDF data in Adobe Acrobat into multiple files, and try printing again.
Cancel printing (Canceling Printing), open the PDF file in an application, and try printing again using the printer driver.
PDL RIP Process. Error
The printer stopped operating normally due to an unknown problem.
Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.
PDL XPS Error
An undefined error occurred.
Restart the machine and try again. If the message is still displayed, make a note of the message and contact your dealer or service representative.
PDL XPS Initialize Error
An unknown error such as not being able to retrieve memory during initialization occurred.
Restart the machine and try again. If the message is still displayed, make a note of the message and contact your dealer or service representative.
PDL XPS Rendering Error
An error occurred in the rendering system.
Restart the machine and try again. If the message is still displayed, make a note of the message and contact your dealer or service representative.
PDL Image Comp. Error
The printer stopped operating normally due to an unknown problem.
Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.
PDL Rendering Timeout
The printer stopped operating normally due to an unknown problem.
Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.
PDL Data Transfer Error
The printer stopped operating normally due to an unknown problem.
Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.
PDL Reg. Access Error
The printer stopped operating normally due to an unknown problem.
Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.
Cannot recall the button settings because other operations are being performed.
The <Personal>/<Shared> cannot be called when another function is being executed.
Call the <Personal>/<Shared> after the operations for the other function are complete.
Register to Home will be canceled and you will be returned to the function screen because you do not have permission to register buttons. Log in as an administrator, then try again.
Registering personal buttons/shared buttons is restricted in user authentication.
Register the button after logging in as an administrator.
Check the following settings.
<Allow Home Screen Customization for Common Use>
<Allow Registration/Editing of Personal Buttons>
The password does not meet the policy requirements. Change the password.
The entered password violates the password policy.
Enter a password that complies with the password policy. If you do not know the password policy, consult your system administrator.
A toner cartridge that cannot be used with this device has been inserted, so printing is currently unavailable. Make sure the specified toner cartridge for this device is inserted.
A toner cartridge that can be used with the machine has not been loaded.
Load the toner cartridge that can be used with the machine. For instructions on checking the model number of the toner cartridge, see Replacement Parts.
To continue using the toner cartridge, press <Close>. If you select this option, the operation of the machine is not guaranteed.
If you are not sure about the remedies, contact your dealer or service representative from which you purchased the toner cartridge.
Printing cannot continue while this message is displayed.
Timer settings for this device and the authentication server may not be synchronized. Contact the system manager.
The date and time settings of the machine and the authentication server are different.
Synchronize the date and time settings of the machine and the authentication server.
Wireless LAN communication error. Turn main power OFF & ON.
An unknown error occurred when configuring the wireless LAN connection.
Restart the machine. Press the power switch to turn the power OFF (Turning OFF the Machine),wait for longer than 10 seconds, and then turn the power ON again (Turning ON the Machine).
Wireless LAN communic. error. Check Wireless LAN Information.
An unknown error occurred when configuring the wireless LAN connection.
Check the wireless LAN settings.
Check the settings and information of the wireless LAN
Check the settings and information of the wireless LAN
Cannot send because the memory is full. Wait a moment, then try again.
The fax could not be sent because there was insufficient memory.
Lower the resolution and try sending again.
Delete unnecessary documents in the memory of the machine to free up space.
Printing Documents in the Memory RX Inbox
Working with Files and Folders in Other Devices
Printing Documents in the Memory RX Inbox
Working with Files and Folders in Other Devices
If this message is displayed frequently, contact your dealer or service representative.
Could not perform the operation because the memory is full.
When using the Scan and Store function, scanning was canceled because the memory became full while scanning the original.
Press <OK> to return to the Basic Features screen. Delete unnecessary data to increase the free space, and try scanning the original again.
Scanning will be canceled because the memory is full. Do you want to print the scanned pages？
When using the Copy function, scanning was canceled because the memory became full while scanning the original.
Press <Yes> to copy the scanned pages. Scan the remaining originals after copying is complete.
Scanning will be canceled because the memory is full. Wait a moment, then try again.
When using the Copy function, scanning was canceled because the memory became full while scanning the original.
Press <OK> to return to the Basic Features screen. Scan the remaining originals after the current copy operation is complete.
Scanning will be canceled because the memory is full. Do you want to send the scanned pages？
When using the Fax or Scan and Send function, scanning was canceled because the memory became full while scanning the original.
Press <Yes> to send the scanned pages. Scan the remaining originals after sending is complete.
Scanning will be canceled because the memory is full. Do you want to store the scanned pages？
When using the Scan and Store function, scanning was canceled because the memory became full while scanning the original.
Press <Yes> to save the scanned pages. Scan the remaining originals after saving is complete.
The amount of data stored for registered users has reached the limit. You can perform operations, but no data (job setting logs, personal settings content, etc.) can be stored this time. To be able to store data from the next time you log in, unnecessary data must be deleted from other users. Contact the system manager or refer to the manual for details.
The user setting information could not be saved because the maximum number of users who can be registered was exceeded.
To save new user setting information, delete any unnecessary user setting information.
Deleting User Setting Information
Deleting User Setting Information
If you are not using the Personalization function, delete user setting information, and then set <Enable Use of Personal Settings> (<Enable Use of Personal Settings>) to <Off>.
You can specify settings to automatically delete old user setting information if the number of users who can be registered is exceeded.
<Action When Maximum Number of Users Exceeded>
<Action When Maximum Number of Users Exceeded>
Register to Home will be canceled because you are not logged in. Return to the function screen, log in, then try again.
Registering shared buttons is restricted in user authentication.
Register the button after logging in as an administrator.
Check the user name, password, or settings.
An incorrect user name or password was set for the LDAP server authentication information.
Check whether the user name and password in <Register LDAP Server> are correct.
Registering the LDAP Server
Registering the LDAP Server
An incorrect domain name was set for the LDAP server authentication information.
Check whether the domain name in <Register LDAP Server> is correct.
Registering the LDAP Server
Registering the LDAP Server
Load paper.
The paper in the paper source has run out.
Load paper in the paper source displayed on the touch panel display.
Loading Paper
Loading Paper
The paper guides in the paper source are in the wrong position.
Adjust the paper guides according to the edges of the paper. Depending on the cut edge of the paper, multiple sheets of paper may be fed together when printing, which can cause paper jams. This can be reduced by changing the orientation of the loaded paper.
The paper settings differ from the paper that is loaded.
Check the paper settings in <Consumables/Others> in 
(Status Monitor). If the paper settings are incorrect, match them with the paper that is loaded. Paper settings can be specified for all the paper sizes and types set in the paper drawers and multi-purpose tray in 
(Settings/Register) 
<Preferences> <Paper Settings>. If you are using the multi-purpose tray, remove the loaded paper and specify the paper settings.
Specifying Paper Size and Type
(Status Monitor). If the paper settings are incorrect, match them with the paper that is loaded. Paper settings can be specified for all the paper sizes and types set in the paper drawers and multi-purpose tray in (Settings/Register) <Preferences> <Paper Settings>. If you are using the multi-purpose tray, remove the loaded paper and specify the paper settings.Specifying Paper Size and Type
The paper settings of the driver or application differ from the paper that is loaded.
Check the paper settings on the [Printing Preferences] screen of the printer driver, and if the paper settings are incorrect, match them with the paper that is loaded.
Scanning was canceled because the data size of the scanned original exceeds the limit. Scanning may be possible if sharpness is reduced, or Original Type is set to Text.
Scanning was canceled because the data of the scanned document exceeded the maximum size that can be handled by the machine.
You may be able to scan by lowering the setting in <Sharpness>, and setting <Original Type> to <Text>.
Information set by the currently logged-in user will not be stored.
The user setting information cannot be saved because the maximum number of users who can be registered was exceeded.
To save new user setting information, delete any unnecessary user setting information.
Deleting User Setting Information
Deleting User Setting Information
You can specify settings to automatically delete old user setting information if the number of users who can be registered is exceeded.
<Action When Maximum Number of Users Exceeded>
<Action When Maximum Number of Users Exceeded>
Login failed. Anonymous access to the authentication server is not allowed. Contact the system manager.
Anonymous access is not allowed in the LDAP server.
Select the check box in [Use authentication information] on the screen for entering information on the LDAP server, and set the user name and password according to the information registered in the LDAP server.
Registering Server Information
Registering Server Information
Login failed. The account information necessary to log in to the authentication server is invalid. Contact the system manager.
The user name or password is not set correctly.
On the screen for entering the information for the LDAP server, set the correct settings according to the settings registered in the LDAP server.
Registering Server Information
Registering Server Information
Cannot log in. Check the login destination.
The login destination information entered on the mobile device side is incorrect.
Confirm that you have specified the correct login destination, and then log in again.
Cannot store the password because the number of passwords stored for each user has reached the limit.
The login user password cannot be registered because the maximum number of passwords has been exceeded.
Delete unnecessary password information.
If a six-digit number is displayed when you are logging in
If an error occurs when you are logging in, a six-digit number may be displayed below the message. Take the necessary measure depending on the six-digit number displayed.
310001
Communication with the authentication server failed.
Check the network cables from the machine and the domain controller (Active Directory).
Check whether the domain controller is down.
Check whether name resolution is working correctly with the DNS server set for the machine on the domain controller.
Try again after augmenting the current value of [Period Until Timeout:] in the Active Directory settings.
310002
When [Use access mode within sites] is enabled on the machine, the site information of Active Directory is not set correctly.
Check whether the site setting on Active Directory is valid.
310003
The network environment is not yet ready.
Check again after a while.
Check whether name resolution to the specified domain name is working correctly (the address can be identified) with the DNS server set for the machine, and then make adjustments as necessary.
The DNS server set for the machine cannot be found, or it is currently unable to communicate. Check the configuration and the communication environment.
322000
A server error has occurred during Kerberos authentication.
In Active Directory, clear the check box for [Do not require Kerberos preauthentication], which is an account option for the logged-in user account. Alternatively, check whether Active Directory is used properly.
322006
The objective user does not exist on the authentication server.
Check whether the authentication user or search user exists on the domain controller to authenticate.
322012
In Active Directory, the check box for [Smart card is required for interactive logon], which is an account option for the logged-in user account, is selected.
In Active Directory, clear the check box for [Smart card is required for interactive logon], which is an account option for the logged-in user account. After clearing the check box, be sure to reset the password. When resetting the password, you can use the same password instead of a new one.
322018
The validity period of the account has expired.
Check the validity period of the account in question.
322023
The validity period of the password has expired.
Change the password.
In Active Directory, check the setting of the account options for the logged-in user account.
322024
The user name or password is wrong when keyboard authentication is performed.
Check the password of the authentication user or search user.
322029
The attempt to communicate with the writable domain controller failed.
Check the network cable from the writable domain controller.
Check whether the writable domain controller is down.
Check whether name resolution is working correctly with the DNS server on the writable domain controller.
Try again after augmenting the current value of [Period Until Timeout:] in the Active Directory settings.
322037
The date and time settings are not identical between the machine and the authentication server.
Ensure that the date and time settings are identical between the machine and the authentication server.
322xxx
A Kerberos authentication error.
A Kerberos error code is displayed in place of xxx.
323000
An error has occurred during LDAP server authentication.
Check whether Active Directory or LDAP service is used properly.
323008
An LDAP server authentication error has occurred in relation to TLS/non-TLS communication.
Check the communication settings (TLS/non-TLS) of the server.
Check whether the communication settings on the device side are identical to those on the server side.
323048
You are attempting to log in as an anonymous user for LDAP server authentication.
Check whether the LDAP service setting permits anonymous user authentication.
323049/323053
The user information for LDAP server authentication is not set correctly.
Check the user name and password of the authentication user or search user.
Check whether the authentication user or search user is invalid, whether their validity period has expired, and whether they are account-locked.
323xxx
An LDAP server authentication (LDAPBind) error.
An LDAPBind error code is displayed in place of xxx.
324000
An error has occurred during LDAP server search.
Check whether Active Directory or LDAP service is used properly.
324xxx
LDAP server search (LDAPSearch) error.
An LDAPSearch error code is displayed in place of xxx.
325000
An error has occurred during LDAP server authentication.
Check whether Active Directory or LDAP service is used properly.
325010
You have attempted to perform registration to a read-only domain controller.
If the domain controller configured in Active Directory is of the read-only type, no user information editing functions (registering/deleting cards, changing PIN) are available. To use the user information registration function, configure a writable domain controller.
325050
The search user set in the Administrator settings page does not have update authority (write access).
Check whether the search user is granted write access to the user attribute that you are going to modify.
325067
You are attempting to modify an attribute of a Relative Distinguished Name (RDN) such as cn attribute.
You are attempting to modify an attribute of a Relative Distinguished Name (RDN) such as cn attribute. The information of such attribute cannot be modified, so specify another attribute.
325xxx
An LDAP server update error.
An LDAPModify error code is displayed in place of xxx.
331000
User authentication failed.
Check the user name and password. If the user name and password are correct, contact your system manager.
331001
The user name has not been entered.
Enter the user name.
331002
Cannot find the user.
Check the user name and password. If the user name and password are correct, contact your system manager. The user may not exist on the LDAP server, or the search user may not have read access to attribute information of the relevant account.
331003
You are using a card that is not registered on the authentication server.
Check whether you are using a valid card.
331004
Card information is double registered on the authentication server.
Contact your system manager.
331005
The validity period of the logged-in user has expired.
Contact your system manager.
331006
The validity value of the card and that on the authentication server are different from each other.
Check whether you are using a valid card. If you are using a valid card, contact your system manager.
331007
A validity value outside the range is set on the authentication server.
Check whether the server is operated with the correct attribute of validity value.
331008
The account of the logged-in user is locked out.
Contact your system manager.
331009
The user ID of the account you are using to log in to the machine is invalid. Or the Active Directory settings may not be correct.
Check whether all of the required attributes are set correctly.
In Active Directory, clear the check box for [Do not require Kerberos preauthentication], which is an account option for the logged-in user account.
331010
To perform authentication for a specific function, you have attempted to log in as a user who is not permitted to use that function.
Contact your system manager.
331011
Login to perform authentication for a specific function failed.
Check which functions the logged-in user is able to use.
331012
The PIN of the logged-in user is invalid.
Enter the PIN again.
331013
The account of the logged-in user is invalid.
Contact your system manager.
332000
User information updating failed.
Updating the user information failed. Check whether the user information you used for updating is valid and whether invalid information is not specified for updating.
332001
Already registered card information.
The card of the logged-in user is already registered. Check whether you are using a valid card. Or contact your system manager.
332002
An invalid attribute was specified for user information updating.
When card information editing functions are used, it is not permitted to make registration with sAMAccountName or userPrincipalName attribute in the Active Directory settings. One solution is to use other attribute.
332003
An invalid login name was specified for user information updating.
It is not permitted to register the name of the logged-in user (login name). Check the user name and contact your system manager.
332004
An invalid display name was specified for user information updating.
It is not permitted to register the display name of the logged-in user. Check the display name attribute value on the server being referred to, and contact your system manager.
332005
An invalid domain name was specified for user information updating.
It is not permitted to register the domain name for the logged-in user. Check the domain name you have selected and contact your system manager.
332006
An invalid email address was specified for user information updating.
It is not permitted to register the email address of the logged-in user. Check the email address attribute value on the server being referred to, and contact your system manager.
332007
An invalid role was specified for user information updating.
Check the attribute value for determining the privileges on the side of the server being referred to, and contact your system manager.
332008
The maximum registerable number of users was exceeded during user information updating.
Contact your system manager.