Settings/Registration] 
[Adjustment/Maintenance] [Adjust Action][Adjust Action]
Adjust the actions of the optional finisher and the machine's finishing functions.
* Values in red text indicate the default setting for each item.
[ Settings/Registration] [Adjustment/Maintenance] [Adjust Action]
Settings/Registration] [Adjustment/Maintenance] [Adjust Action]Reposition the staples of the saddle stitch unit so that stapling can be performed. Remove any paper output to the booklet tray before performing this operation.
Perform this operation if stapling is not performed after you remove jammed staples or replace the staple case. When you perform this operation, the machine feeds paper to the saddle stitch unit and staples it several times.
Perform this operation if stapling is not performed after you remove jammed staples or replace the staple case. When you perform this operation, the machine feeds paper to the saddle stitch unit and staples it several times.
* This item is displayed only on machines with the option installed.
NOTE
Usable Paper
Plain paper
Any of the following paper sizes:
A3
B4
A4R
305 x 457 mm
Legal
Letter R
11" x 17"
If Unusable Paper Is Loaded in a Paper Source
Configure the settings to disable the use of that paper source. Using the Appropriate Paper Source for Each Function
[ Settings/Registration] [Adjustment/Maintenance] [Adjust Action]
Settings/Registration] [Adjustment/Maintenance] [Adjust Action]Adjust the saddle stitch fold position and staple position so that they are at the center of the paper. Print a test page, check the current state of the fold position and the shift width on the test page, and then perform adjustment. Adjusting the Saddle Stitch Fold Position and Staple Position
* This item is displayed only on machines with the option installed.
[ Settings/Registration] [Adjustment/Maintenance] [Adjust Action]
Settings/Registration] [Adjustment/Maintenance] [Adjust Action]Adjust the double staple width.
* This item is displayed only on machines with the option installed.
120 to 150 mm (4 3/4 to 5 7/8") * In 1 mm (1/16") increments |
NOTE
When the paper width is smaller than 257 mm (10 1/8"), double staple width is fixed to [120 mm] or [4_3/4"].
Depending on the installed option, this setting is valid only when the Offset mode is not set. The mode is set to [120 mm] or [4_3/4"] when used with the Offset mode.
Depending on the installed option, the productivity of the machine may be reduced if this mode is set to [120 mm] or [4_3/4"].
[ Settings/Registration] [Adjustment/Maintenance] [Adjust Action]
Settings/Registration] [Adjustment/Maintenance] [Adjust Action]Set whether to give priority to the speed or precision of the puncher.
* This item is displayed only on machines with the option installed.
[Speed Priority], [Precision Priority] |
[ Settings/Registration] [Adjustment/Maintenance] [Adjust Action]
Settings/Registration] [Adjustment/Maintenance] [Adjust Action]Set whether to give priority to the double stapling speed or to precision.
* This item is displayed only on machines with the option installed.
[Speed Priority], [Precision Priority] |
NOTE
This mode is enabled only when using the following paper:
Paper size: The width for the feeding direction is 215.9 mm (8 1/2") or less
Paper type: Plain, Heavy 1, Color, Pre-punched
Paper weight: 64 g/m² to 128 g/m² (17 lb bond to 32 lb bond)
If you select [Speed Priority], edges of stapled output paper may not be aligned.
[ Settings/Registration] [Adjustment/Maintenance] [Adjust Action]
Settings/Registration] [Adjustment/Maintenance] [Adjust Action]You can trim the edge of booklets. This setting enables you to adjust the trimming width.
* This item is displayed only on machines with the option installed.
2.0 to 28.0 (mm) (0.08 to 0.78 (")) * In 0.1 mm (0.01") increments |
[ Settings/Registration] [Adjustment/Maintenance] [Adjust Action]
Settings/Registration] [Adjustment/Maintenance] [Adjust Action]Adjust the fold position for each paper size. Adjusting the Paper Fold Position
* This item is displayed only on machines with the option installed.
* The items displayed vary depending on the options that are installed. Options with Folding Functions
For 6100 Series and 8100 Series (When the Finisher and Paper Folding Unit Is Installed)
For 6100 Series and 8100 Series (When the Paper Folding Unit Is Installed)
For 6100 Series (When the Booklet Finisher Is Installed)
For 6100 Series and 8100 Series (When the Paper Folding Unit Is Installed)
For 6100 Series (When the Booklet Finisher Is Installed)
[Adjust Z-Fold Position] -2.0 to 0.0 to +1.5 (mm) * In 0.5 mm increments [Adjust Saddle C-Fold Position] [A] 0.0 to 6.0 mm (mm) * In 0.5 mm increments [B] 0.0 to 3.0 mm (mm) * In 0.5 mm increments [Adjust C-Fold Position] -7.0 to -1.0 to +5.0 (mm) * In 0.5 mm increments [Adjust Accordion Z-Fold Position] -7.0 to -1.0 to +5.0 (mm) * In 0.5 mm increments [Adjust Double Parallel Fold Position] [A] -2.0 to -1.0 to +5.0 (mm) * In 0.5 mm increments [B] 0.0 to 1.0 to +5.0 (mm) * In 0.5 mm increments [Adjust Half Fold Position] -2.0 to 0.0 to 2.0 (mm) * In 0.5 mm increments [Adjust Saddle Fold Position] [Current State] [A Is Shorter], [A and B Are Equal], [B Is Shorter] [Shift Width (a)] 0.0 to 2.0 (mm) * In 0.1 mm increments |
For 8100 Series (When the Booklet Finisher Is Installed)
[Current State] [A Is Shorter], [A and B Are Equal], [B Is Shorter] [Shift Width (a)] 0.0 to 2.0 (mm) * In 0.1 mm increments |
[ Settings/Registration] [Adjustment/Maintenance] [Adjust Action]
Settings/Registration] [Adjustment/Maintenance] [Adjust Action]The copied or printed paper may shrink because of temperature, humidity, or a characteristic of the paper type. In this case, this mode enables you to align copied or printed papers by adjusting the position of the alignment guide inside the finisher so as to staple the aligned papers.
* This item is displayed only on machines with the option installed.
-3.0 to 0.0 to +3.0 (mm) * In 0.1 mm increments |
NOTE
If the value in this mode is increased, a paper jam may occur.
[ Settings/Registration] [Adjustment/Maintenance] [Adjust Action]
Settings/Registration] [Adjustment/Maintenance] [Adjust Action]Adjust paper alignment when outputting to Tray A of a finisher.
* This item is displayed only on machines with the option installed.
-3.0 to 0.0 to +3.0 (mm) * In 0.1 mm increments |
NOTE
You cannot align output paper in the following situations:
When using paper smaller than A5R or STMTR
When using different size paper together
If you set [Align Output Paper of Diff. Sizes (Diff. Widths)] to [On], you can align output paper by paper width.
[ Settings/Registration] [Adjustment/Maintenance] [Adjust Action]
Settings/Registration] [Adjustment/Maintenance] [Adjust Action]Adjust paper alignment when outputting to Tray B of a finisher.
* This item is displayed only on machines with the option installed.
-3.0 to 0.0 to +3.0 (mm) * In 0.1 mm increments |
NOTE
You cannot align output paper in the following situations:
When using paper smaller than A5R or STMTR
When using different size paper together
If you set [Align Output Paper of Diff. Sizes (Diff. Widths)] to [On], you can align output paper by paper width.
[ Settings/Registration] [Adjustment/Maintenance] [Adjust Action]
Settings/Registration] [Adjustment/Maintenance] [Adjust Action]Adjust paper alignment when outputting to Tray C of a finisher.
* This item is displayed only on machines with the option installed.
-3.0 to 0.0 to +3.0 (mm) * In 0.1 mm increments |
NOTE
You cannot align output paper in the following situations:
When using paper smaller than A5R or STMTR
When using different size paper together
If you set [Align Output Paper of Diff. Sizes (Diff. Widths)] to [On], you can align output paper by paper width.
[ Settings/Registration] [Adjustment/Maintenance] [Adjust Action]
Settings/Registration] [Adjustment/Maintenance] [Adjust Action]You can give priority to productivity or alignment for the output paper when using Thin paper.
* This item is displayed only on machines with the option installed.
[Productivity Priority], [Alignment Priority] |
NOTE
This item is available only when outputting on Tray B of a finisher.
[ Settings/Registration] [Adjustment/Maintenance] [Adjust Action]
Settings/Registration] [Adjustment/Maintenance] [Adjust Action]You can give priority to productivity or alignment for the output paper.
* This item is displayed only on machines with the option installed.
[Productivity Priority], [Alignment Priority] |
NOTE
This item is available only when outputting on Tray B of a finisher.
[ Settings/Registration] [Adjustment/Maintenance] [Adjust Action]
Settings/Registration] [Adjustment/Maintenance] [Adjust Action]Set the amount of time until the machine automatically staples the paper bundle after it is inserted, when using manual stapling.
* This item is displayed only on machines with the option installed.
1 to 3 to 5 sec. |
[ Settings/Registration] [Adjustment/Maintenance] [Adjust Action]
Settings/Registration] [Adjustment/Maintenance] [Adjust Action]You can give priority to productivity or alignment for the output paper when using saddle fold.
* This item is displayed only on machines with the option installed.
[Productivity Priority], [Alignment Priority] |
NOTE
This mode is enabled only when using the following paper:
Paper type: Thin, Plain, Heavy, Coated
Paper weight: 52 g/m² to 63 g/m² (14 lb Bond to 16 lb bond) for Thin paper, 64 g/m² to 105 g/m² (17 lb bond to 28 lb bond) for Plain paper, 106 g/m² to 209 g/m² (29 lb bond to 110 lb index)) for Heavy paper, 106 g/m² to 209 g/m² (29 lb bond to 110 lb index) for Coated paper
If you select [Productivity Priority], edges of saddle folded output paper may not be aligned.
[ Settings/Registration] [Adjustment/Maintenance] [Adjust Action]
Settings/Registration] [Adjustment/Maintenance] [Adjust Action]Adjust the amount of time to touch [
Start] on the control panel. When you touch the button for the set amount of time, the machine recognizes that the button is pressed, and the processing starts.
Start] on the control panel. When you touch the button for the set amount of time, the machine recognizes that the button is pressed, and the processing starts.-1 to 0 to +7 |