[Fax Settings]
Specify the settings for receiving and forwarding faxes.
* Values in bold red text are the default settings for each item.
* Values in bold red text are the default settings for each item.
[Print on Both Sides]
[Menu] 
[Function Settings] [Receive/Forward] [Fax Settings]
[Function Settings] [Receive/Forward] [Fax Settings]Specify whether to use 2-sided printing for received faxes.
[Off] [On] |
[Select Drawer]
[Menu] [Function Settings] [Receive/Forward] [Fax Settings]
[Function Settings] [Receive/Forward] [Fax Settings]Specify how the machine prints a received fax when there is no paper matching to the paper size of the received fax.
[Switch A] [Off] [On] [Switch B] [Off] [On] [Switch C] [Off] [On] [Switch D] [Off] [On] |
[ECM RX]
[Menu] [Function Settings] [Receive/Forward] [Fax Settings]
[Function Settings] [Receive/Forward] [Fax Settings]ECM (Error Correction Mode) is a function that conducts checking and correction to ensure that corrupted images are not sent when an error occurs during image reception. Here, specify whether the ECM function is used for reception. If you use ECM reception, error checking is carried out by both the sender and recipient during communication, so the ECM function must also be enabled at the sender's end. ECM reception may slow down communication because error checking and correction are conducted during communication. Note also that even when ECM reception is enabled, errors may still occur depending on the state of the phone lines. Enable ECM transmission on the machine to reduce the number of errors that occur when the machine sends data. [ECM TX] |
[Off] [On] |
[RX Start Speed]
[Menu] [Function Settings] [Receive/Forward] [Fax Settings]
[Function Settings] [Receive/Forward] [Fax Settings]It may take some time for reception to begin due to factors such as a poor phone line connection. If this occurs, adjust the initial communication speed to a lower level.
[33600 bps] [14400 bps] [9600 bps] [7200 bps] [4800 bps] [2400 bps] |
[Reduce RX Size]
[Menu] [Function Settings] [Receive/Forward] [Fax Settings]
[Function Settings] [Receive/Forward] [Fax Settings]Specify whether to reduce images when printing or saving received faxes. Set the reduction ratio to [Auto] in this setting to reduce images to fit the paper size. When specifying the reduction ratio, set a value between [97%] and [75%]. To maintain the aspect ratio in reduced images, set the reduction direction to [Vertical/Horizontal]. To reduce images in the vertical direction only, specify [Vertical Only]. |
[Off] [On] [Reduction Ratio] [Auto] [97%] [95%] [90%] [75%] [Reduction Direction] [Vertical/Horizontal] [Vertical Only] |
[Forwarding Settings]
[Menu] [Function Settings] [Receive/Forward] [Fax Settings]
[Function Settings] [Receive/Forward] [Fax Settings]Specify the settings for forwarding faxes. Auto Forwarding and Backing Up Received Faxes
[Enable Forwarding Settings]
[Menu] [Function Settings] [Receive/Forward] [Fax Settings] [Forwarding Settings]
[Function Settings] [Receive/Forward] [Fax Settings] [Forwarding Settings]Specify whether the content of received faxes is automatically forwarded or saved to a preset destination.
If you specify [On] in this setting, also specify the forwarding or save destination and, if needed, the file name.
If you specify [On] in this setting, also specify the forwarding or save destination and, if needed, the file name.
[Off] [On] [Forwarding Destination] [File Name] |
[Print Images]
[Menu] [Function Settings] [Receive/Forward] [Fax Settings] [Forwarding Settings]
[Function Settings] [Receive/Forward] [Fax Settings] [Forwarding Settings]Specify whether to print forwarded faxes.
You can also opt to print only faxes that cannot be forwarded.
You can also opt to print only faxes that cannot be forwarded.
[Off] [On] [Only When Error Occurs] |
[Store Images in Memory]
[Menu] [Function Settings] [Receive/Forward] [Fax Settings] [Forwarding Settings]
[Function Settings] [Receive/Forward] [Fax Settings] [Forwarding Settings]Specify whether faxes that could not be forwarded due to an error are stored in the machine's memory.
[Off] [Only When Error Occurs] |