[Setup] Menu ([Std Network Menu] Options)

NOTE
Table description After changing the settings for this item, cycle the power of the printer or perform a hard reset to make the settings effective. This item is displayed only when all the following conditions are fulfilled. [Network] in [Interface Connection] is set to [On]. If [Primary Network Setting] is set to [Standard Network], specify the setting for [Primary Network Setting] in the [Extension Card] page in the Remote UI or [Extension Card] on the control panel. This option is displayed only when [Network] in [Interface Connection] is set to [On]. Bold values in the table indicate the default settings. The setting items or setting values with "*" may not be displayed depending on the availability of the optional accessories and other settings.

NOTE

Table description

After changing the settings for this item, cycle the power of the printer or perform a hard reset to make the settings effective.

This item is displayed only when all the following conditions are fulfilled.

[Network] in [Interface Connection] is set to [On].

If [Primary Network Setting] is set to [Standard Network], specify the setting for [Primary Network Setting] in the [Extension Card] page in the Remote UI or [Extension Card] on the control panel.

This option is displayed only when [Network] in [Interface Connection] is set to [On].

Bold values in the table indicate the default settings.

The setting items or setting values with "*" may not be displayed depending on the availability of the optional accessories and other settings.

Setting Item

Setting Value

Setting

[TCP/IP Settings]

Specifies the TCP/IP setting for the print server equipped with this printer.

[IP v.4 Settings]

[IP Mode]:[Auto], [Manual]

Select the method for setting the IP address.

When setting the IP address using any one of DHCP, BOOTP, or RARP, select [Auto].

When specifying the IP address to the printer directly, select [Manual].

[Protocol]*:

[Use DHCP]: [Off], [On]

[Use BOOTP]: [Off], [On]

[Use RARP]: [Off], [On]

If you set [IP Mode] to [Auto], select which protocol you want to use. Set each of [Use DHCP], [Use BOOTP], and [Use RARP] to [ON] (use) or [OFF] (do not use).

[IP Address Settings]:

[IP Address]: 0.0.0.0

[Subnet Mask]: 0.0.0.0

[Gateway Address]: 0.0.0.0

Specify [IP Address], [Subnet Mask], and [Gateway Address]. For the method for entering the addresses, see "Method for entering addresses " below the table.

[IP Address Range]:

[Reject Receive/Print]: [Off], [On]

[Reject Address Set.]*: Reject IP Address 1 to 8

[Permit Receive/Print]: [Off], [On]

[Permit Address Set.]*: Permit IP Address 1 to 8

[Reject Set/Browse]: [Off], [On]

[Reject Address Set.]*: Reject IP Address 1 to 8

[Permit Set/Browse]: [Off], [On]

[Permit Address Set.]*: Permit IP Address 1 to 8

Restrict the users who can print or perform the printer settings using IP addresses.

To reject specific users from printing, set [Reject Receive/Print] to [On], and then specify the addresses to be rejected in [Reject Address Set.].

To permit specific users to print, set [Permit Receive/Print] to [On], and then specify the addresses to be permitted in [Permit Address Set.].

To reject specific users from changing the settings, set [Reject Set/Browse] to [On], and then specify the addresses to be rejected in [Reject Address Set.].

To permit specific users to change the settings, set [Permit Set/Browse] to [On], and then specify the addresses to be permitted in [Permit Address Set.].

[DNS]:

[Primary Address]: 0.0.0.0

[Secondary Address]: 0.0.0.0

Specify [Primary Address] and [Secondary Address] for DNS.

For the method for entering the addresses, see "Method for entering addresses " below the table.

*	Specify the settings for [DNS Host Name], [DNS Domain Name], and [DNS Dynamic Update] from the Remote UI. "Configuring the Protocol Settings"

[IP v.6 Settings]

[IP v.6]: [Off], [On]

If you want to use IP v. 6, specify [On].

*	Specify the setting for IP v. 6 from the Remote UI. "Setting IP v. 6"

[WINS Resolution]

[Off], [On]

If you want to use WINS Resolution, specify [On].

*	Specify the following settings from the Remote UI.
	[WINS Server Address] [Scope ID] [SMB Server Name] [SMB Workgroup Name] "Configuring the Protocol Settings"

[ARP/PING]

[Off], [On]

If you want to use the ARP/PING function, specify [On].

[FTP]

[FTP Print]: [Off], [On]

[FTP Settings]: [Off], [On]

If you want to use FTP Print, set [FTP Print] to [On].

If you want to perform the settings using FTP Client, set [FTP Settings] to [On].

*	Specify the settings for [FTP Print User Name] and [FTP Print Password] from the Remote UI. "Configuring the Protocol Settings"

[LPD Print]

[Off], [On]

If you want to use LPD Print, specify [On].

*	Specify the setting for [Print LPD Banner Page] from the Remote UI. "Configuring the Protocol Settings"

[RAW Print]

[Off], [On]

If you want to use RAW Print, specify [On].

*	Specify the setting for [Bidirectional Communication] from the Remote UI. "Configuring the Protocol Settings"

[IPP Print]

[Off], [On]

If you want to use IPP Print, specify [On].

*	Specify the settings for [IPP Authentication], [IPP User Name], and [IPP Password] from the Remote UI. "Configuring the Protocol Settings"

[WSD]

[WSD Print]: [Off], [On]

[WSD Browsing]*: [Off], [On]

[Multicast Discovery]: [Off], [On]

If you want to use WSD Print, set [WSD Print] to [On], and then specify the following settings.

If you want to obtain printer information using WSD, set [WSD Browsing] to [On]. If you set [WSD Print] to [On], [WSD Browsing] is not displayed. ([WSD Browsing] is fixed at [On].)

If you want to set the printer to respond to requests from multicast discovery, set [Multicast Discovery] to [On].

[HTTP]

[Off], [On]

If you want to use the HTTP function, specify [On].

Specifying [Off] makes the Remote UI and IPP Print invalid.

[Proxy Settings]*

[Proxy]: [Off], [On]

If you want to use the proxy function, specify [On].

[Server Address]*: -

Enter the proxy server address to be used for the proxy function.

[Port Number]*: 0 to 80 to 99999

Enter the port number of the proxy server to be used for the proxy function. You can specify between [0] and [99999].

[Same Domain]*: [Use Proxy], [Do Not Use Proxy]

If you want to use the proxy function also for the same domain, specify [Use Proxy].

[Proxy Authentication]*: [Off], [On]

If you want to use the proxy authentication function, specify [On].

[User Name]*: -

Enter the user name to be used for the proxy authentication. Up to 24 alphanumeric characters can be entered.

[Password]*: -

Enter the password to be used for the proxy authentication. Up to 24 alphanumeric characters can be entered.

[SNTP]

[Off], [On]

When obtaining time using the SNTP Client function, specify [On].

*	Specify the settings for [NTP Server Name] and [Polling Interval] from the Remote UI. "Configuring the Protocol Settings"

[Response]

[Off], [On]

If you want to set the printer so that it responds to searches that used the multicast discovery function, specify [On].

*	Specify the setting for [Scope Name] from the Remote UI. "Configuring the Protocol Settings"

[MAC Address Settings]

[Permit Receive]: [Off], [On]

[Permit Address Set.]*: [Permit MAC Add. 1] to [Permit MAC Add. 50]

Permits access only from users with a specific MAC address. Set [Permit Receive] to [On], and then specify the addresses to be permitted in [Permit Address Set.].

[NetWare Settings]

[NetWare]: [Off], [On]

[Frame Type]*: [Auto Detect], [Ethernet II], [Ethernet 802.2], [Ethernet 802.3], [Ethernet SNAP]

[Print Service]*: [Bindery PServer], [RPrinter], [NDS PServer], [NPrinter]

Configures the NetWare network settings.

"Configuring the Protocol Settings"

[AppleTalk]

[Off], [On]

Specifies whether the printer should use AppleTalk.

"Configuring the Protocol Settings"

[SNMP v.1]

[Off], [On]

Specifies whether the printer should use the SNMP v. 1 protocol.

"Restricting the Users Who Can Monitor/Change the Settings Using the SNMP Protocol"

[SNMP v.3 Settings]

[SNMP v.3]: [Off], [On]

[User Settings 1] to [User Settings 5]*: [Authent. Password]
[Encryption Password]

Specify the settings related to SNMP v. 3 protocol.

"Restricting the Users Who Can Monitor/Change the Settings Using the SNMP Protocol"

[Start Wait Time]*

0 to 300 seconds

Specifies the time interval from when the printer is turned ON to when the protocol starts.

"Specifying the Setting for Startup Waiting Time"

[Remote UI Settings]

[Remote UI]: [Off], [On]

[SSL]*: [Off], [On]*

Specifies whether the printer should use the Remote UI.

Also, whether to use SSL for communication by the Remote UI is specified.

"Setting "a Key and Its Certificate" to Be Used for the SSL Encrypted Communication Function"

[Ethernet Driver]*

[Auto Detect]: [Off], [On]

[Communication Mode]*: [Half Duplex], [Full Duplex]

[Ethernet Type]*: [10 Base-T], [100 Base-TX]

Configures the Ethernet driver.

"Changing the Network Transmission Speed or Transfer Mode"

[MAC Address]*

(Display only)

Displays the MAC address of the printer.

[Initialize Network]

By the initialization in this item, you can reset the network settings to the default settings.

"Initializing the Network Settings"

Method for entering addresses

1.	Move the cursor to each field (an area separated by periods to enter three-digit numbers) in which you want to enter the address, by pressing [ ] or [ ]. (The number in the field blinks, allowing you to enter a value.)
2.	Enter the numbers. ([ ] increases the value and [ ] decreases the value.)
3.	After entering values in all the fields, press [OK] to confirm the settings.