Printing Using the Multi-Purpose Tray

If you are making prints on tracing paper, labels, transparencies, nonstandard paper size stock, or envelopes, load the paper stock into the multi-purpose tray.

IMPORTANT
Note the following points when using the multi-purpose tray: Paper Quantity: one to approximately 100 sheets (20 lb bond (80 g/m2), stack approximately 3/8" (10 mm) high) Paper Size: 3 7/8" x 5 1/2" to 12 5/8" x 18" (99 mm x 139.7 mm to 320 mm x 457.2 mm) Paper Weight: 17 lb bond to 80 lb cover (64 to 220 g/m2) Paper which has been rolled or curled must be straightened out prior to use, to allow the paper to feed smoothly through the multi-purpose tray (allowable curl amount: less than 3/8" (10 mm) for normal paper, less than 1/5" (5 mm) for heavy paper). There are some types of paper stock, which may meet the above specifications, but cannot be fed into the multi-purpose tray. Fan the paper well before loading it. Thin paper, recycled paper, pre-punched paper, heavy paper, labels, and transparencies should be fanned particularly well before loading it. Do not load different size/type paper at the same time. Be sure to correctly set the paper type. When printing on special types of paper, such as heavy paper or transparencies, be sure to correctly set the paper type, especially if you are using heavy paper. If the type of paper is not set correctly, it could adversely affect the quality of the image. Moreover, the fixing unit may become dirty and require a service repair, or the paper could jam.

IMPORTANT

Note the following points when using the multi-purpose tray:

Paper Quantity: one to approximately 100 sheets (20 lb bond (80 g/m2), stack approximately 3/8" (10 mm) high)

Paper Size: 3 7/8" x 5 1/2" to 12 5/8" x 18" (99 mm x 139.7 mm to 320 mm x 457.2 mm)

Paper Weight: 17 lb bond to 80 lb cover (64 to 220 g/m2)

Paper which has been rolled or curled must be straightened out prior to use, to allow the paper to feed smoothly through the multi-purpose tray (allowable curl amount: less than 3/8" (10 mm) for normal paper, less than 1/5" (5 mm) for heavy paper). There are some types of paper stock, which may meet the above specifications, but cannot be fed into the multi-purpose tray.

Fan the paper well before loading it. Thin paper, recycled paper, pre-punched paper, heavy paper, labels, and transparencies should be fanned particularly well before loading it.

Do not load different size/type paper at the same time.

Be sure to correctly set the paper type. When printing on special types of paper, such as heavy paper or transparencies, be sure to correctly set the paper type, especially if you are using heavy paper. If the type of paper is not set correctly, it could adversely affect the quality of the image. Moreover, the fixing unit may become dirty and require a service repair, or the paper could jam.

NOTE
For high-quality printouts, use paper recommended by Canon.

Standard Size

You can select standard inch paper, or A or B series paper.

Custom Size

You can load nonstandard paper sizes (3 7/8" x 5 1/2" to 12 5/8" x 18" (99 mm x 139.7 mm to 320 mm x 457.2 mm)).

Envelope

The following envelopes can be loaded into the multi-purpose tray:

COM10 No.10: 4 1/8" x 9 1/2" (104.7 mm x 241.3 mm)

ISO-B5: 7" x 9 7/8" (176 mm x 250 mm)

Monarch: 3 7/8" x 7 1/2" (98.4 mm x 190.5 mm)

ISO-C5: 6 3/8" x 9" (162 mm x 229 mm)

DL: 4 3/8" x 8 5/8" (110 mm x 220 mm)

Nagagata 3: 4 3/4" x 9 1/4" (120 mm x 235 mm)

Yougatanaga 3: 4 3/4" x 9 1/4" (120 mm x 235 mm)

Kakugata 2: 9 1/2" x 13 1/2"(240 mm x 332 mm)

For more information on specific envelope measurements, see "Available Paper Stock."

Open the multi-purpose tray.

NOTE
If the paper size you are going to load into the multi-purpose tray is different from the paper size stored in [Register Multi-Purpose Tray Defaults] in [Preferences] (Settings/Registration), set [Register Multi-Purpose Tray Defaults] to 'Off'. (See "Registering Multi-Purpose Tray Defaults.")

If the paper you want to specify is already loaded in the multi-purpose tray:

If the paper loaded in the multi-purpose tray is not the paper that you want to specify:

If the paper you want to specify is already loaded in the multi-purpose tray:

Press [Select Paper] → specify the loaded paper → proceed to step 6.

Select the paper currently loaded in the multi-purpose tray, as shown below.

If the paper loaded in the multi-purpose tray is not the paper that you want to specify:

Check to see if any job is reserved. (See "Checking and Cancelling Jobs from the Job Status Screen.")

If there is a current or reserved job, you can reserve a change of paper for the multi-purpose tray. For more information, see the following:

Reserving a Job Using a Paper Type Different to the Current Paper in the Multi-Purpose Tray for Copy

Reserving a Job Using a Paper Type Different to the Current Paper in the Multi-Purpose Tray for Access Stored Files

If there is no reserved job, remove any paper remaining in the multi-purpose tray → continue the procedure from step 2.

Adjust the slide guides to match the size of the paper.

If you are feeding large size paper, pull out the auxiliary tray.

Load the paper into the multi-purpose tray.

Make sure that the height of the paper stack does not exceed the loading limit mark (

If the paper is curled when using the multi-purpose tray, a paper jam may occur. Therefore, fix the curling as indicated in the diagram before loading the paper into the multi-purpose tray.

To print on the backside of preprinted paper, load the preprinted paper face down into the multi-purpose tray, as shown in the illustration below.

IMPORTANT
When loading paper into the multi-purpose tray, align the paper stack neatly between the slide guides. If the paper is not loaded correctly, a paper jam may occur. When loading paper into the multi-purpose tray, align the paper stack evenly between the slide guides. The paper may not be fed if the slide guides are set to a position narrower than the paper, causing the paper to curl.

NOTE
If there are instructions on the paper package about which side of the paper to load, follow those instructions. When the paper is loaded into the multi-purpose tray, the side facing down is the one printed on. If problems, such as poor print quality or paper jams occur, try turning the paper stack over and reload it. For more information on the print direction of preprinted paper (paper which has logos or patterns already printed on it), see "Relationship Between the Original Orientation and Paper Orientation."

NOTE

If there are instructions on the paper package about which side of the paper to load, follow those instructions.

When the paper is loaded into the multi-purpose tray, the side facing down is the one printed on.

If problems, such as poor print quality or paper jams occur, try turning the paper stack over and reload it.

For more information on the print direction of preprinted paper (paper which has logos or patterns already printed on it), see "Relationship Between the Original Orientation and Paper Orientation."

If you are loading envelopes into the multi-purpose tray:

Take five envelopes, loosen them as shown, and then stack them together.

Repeat this step five times for each set of five envelopes.

Place the envelopes on a clean, level surface, and press all the way around the envelopes by hand, in the direction of the arrows, to remove any curls.

Repeat this step five times for each set of five envelopes.

Hold down the four corners of the envelopes firmly, so that they and the sealed or glued portion stay flat.

IMPORTANT
If you use envelopes that have glue attached to their flaps, the glue may melt due to the heat and pressure of the fixing unit. Take special care to spread the envelopes out in the direction that they will be fed.

IMPORTANT
Do not print on the backside of the envelopes (the side with the flap). If the envelopes become filled with air, flatten them by hand before loading them into the multi-purpose tray.

Load the envelopes in the direction indicated in the illustration.

If you are using Nagagata 3 or Kakugata 2:

If you are using ISO-B5:

If you are using COM10 No.10, Monarch, DL, ISO-C5, or Yougatanaga 3:

IMPORTANT
The multi-purpose tray can hold five envelopes at a time. If the envelopes do not pass through the machine properly even if the procedures up to this point have been followed, repeat the procedures by feeding once for each envelope. Envelopes may be creased in the printing process.

Select the desired paper size.

IMPORTANT
Set the paper or envelope size to the same size as the paper or envelopes loaded in the multi-purpose tray. Selecting paper or envelopes of a different size may cause a paper jam.

If you want to select a standard paper size:

If you want to select a nonstandard paper size:

If you want to select an envelope size:

If you want to select a standard paper size:

Select the desired paper size → press [Next].

NOTE
To select an A or B series paper size, press [A/B Size].

If you want to select a nonstandard paper size:

Press [Custom Size].

Press [X] or [Y] → enter a value → press [OK].

You can also select a size button ([S1] to [S4]) containing a stored paper size setting, instead of entering values.

NOTE
If you make a mistake when entering values, press (Clear) on the touch panel display → enter the correct values. To select a registered paper size stored in a size button ([S1] to [S4]), you must store the irregular paper size in the size button beforehand. For instructions on storing irregular paper sizes, see "Registering/Editing/Deleting Custom Paper Sizes."

Press [Next].

If you want to select an envelope size:

Press [Envelope].

IMPORTANT
If the envelope type is not selected correctly, a paper jam will occur.

Select the envelope type → press [OK].

Press [Next] → [OK] → proceed to step 6.

Select the desired paper type → press [OK].

To set the plain paper type, press [Plain Paper Weight Set].

If you are using a paper type that is not listed, press [Details] → select the paper type → press [OK].

If you are printing on the backside of a previously printed sheet, press [2nd Side of 2-Sided Page].

NOTE
You can select [Transparency] only if [LTR] is selected as the paper size. For more information on paper types, see "Available Paper Stock." You can register a paper type that is not listed in [Detailed Settings] in the Multi-Purpose Tray Settings: See "Registering/Editing Custom Paper Types."

Press [OK].

If you make a mistake when specifying settings for paper loaded in the multi-purpose tray, remove the paper from the tray, place the paper back in the tray, and then specify the settings again.

Place your originals → select the desired settings.

If the Copy function is selected, place your originals.

If you are printing documents stored in USB memory, the Fax/I-Fax Inbox, or the Advanced Space of another machine on the network, this step is not necessary.

Press

(Start).

If you are printing documents stored in USB memory, the Fax/I-Fax Inbox, or the Advanced Space of another machine on the network, this step is not necessary.

Scanning or printing starts.

NOTE
To cancel all settings and return the machine to the default mode, press (Reset). However, even if you have selected files in [Access Stored Files], the files will be deselected.

IMPORTANT
Feed tracing paper and coated paper one sheet at a time, and remove each sheet as it is delivered to the output tray. Loading several sheets together may cause paper jams. Depending on the type of heavy paper you want to load, if you load multiple sheets of heavy paper into the multi-purpose tray, a paper jam may occur. In this case, load only one sheet of heavy paper at a time. If you are making two-sided prints, select the 2-Sided mode. The printed-paper may crease depending on the moisture absorption condition of the paper. To print on the backside of preprinted paper, load the paper into the multi-purpose tray, and press [2nd Side of 2-Sided Page] on the paper selection screen that appears. If you are printing on envelopes, do not allow more than 10 envelopes to accumulate in the output tray. Always empty the output tray once 10 envelopes have accumulated.

IMPORTANT

Feed tracing paper and coated paper one sheet at a time, and remove each sheet as it is delivered to the output tray. Loading several sheets together may cause paper jams.

Depending on the type of heavy paper you want to load, if you load multiple sheets of heavy paper into the multi-purpose tray, a paper jam may occur. In this case, load only one sheet of heavy paper at a time.

If you are making two-sided prints, select the 2-Sided mode. The printed-paper may crease depending on the moisture absorption condition of the paper.

To print on the backside of preprinted paper, load the paper into the multi-purpose tray, and press [2nd Side of 2-Sided Page] on the paper selection screen that appears.

If you are printing on envelopes, do not allow more than 10 envelopes to accumulate in the output tray. Always empty the output tray once 10 envelopes have accumulated.

NOTE
When scanning the following originals, you cannot use the Automatic Paper Selection mode. Use the Manual Paper Selection mode when scanning these types of originals: Transparencies and other highly transparent objects Originals with an extremely dark background Envelopes may be creased in the printing process.