Setting IPv4 Address
 |
|
The machine's IPv4 address can be either assigned automatically by a dynamic IP addressing protocol, such as DHCP, or entered manually. When connecting the machine to a wired LAN, make sure that the connectors of the LAN cable are firmly inserted into the ports (Connecting to a Wired LAN). You can test the network connection if necessary.
|
Setting IPv4 Address
1
Tap <Menu> in the <Home> screen.
2
Tap <Network Settings>.
If a screen for entering a System Manager ID and PIN is displayed, enter the System Manager ID and PIN, tap <Apply>, and press 
. Setting the System Manager ID (imageRUNNER 2206N / 2006N)
. Setting the System Manager ID (imageRUNNER 2206N / 2006N)3
Select <TCP/IP Settings> 
<IPv4 Settings> <IP Address Settings>.
<IPv4 Settings> <IP Address Settings>.4
Configure IP address settings.
<Auto Acquire>Select to automatically assign an IP address via a protocol such as DHCP. When <Auto Acquire: On> is displayed, automatic addressing is enabled.
<Manually Acquire>Select to configure the IP address settings by manually entering an IP address. In order to select this option, <Auto Acquire> must be set to <Off>.
<Check Settings>Select when you want to view the current IP address settings.
Automatically assigning an IP address
|
1
|
Select <Auto Acquire>
<Select Protocol>. |
|
2
|
Tap <DHCP>, <BOOTP>, or <RARP>.
  If you do not want to use DHCP/BOOTP/RARP to assign an IP address Select <Off>. If you select <DHCP>, <BOOTP>, or <RARP> when these services are unavailable, the machine will waste time and communications resources searching the network for these services. |
|
3
|
Check that <Auto IP> is set to <On>.
If <Off> is selected, change the setting to <On>.
|
|
4
|
Tap <Apply>.
|
IP addresses assigned via DHCP/BOOTP/RARP override the address obtained via Auto IP.
Manually entering an IP address
|
1
|
Check that <Auto Acquire> is set to <Off>.
 If <On> is displayed, tap <Auto Acquire>, and set both <Select Protocol> and <Auto IP> to <Off>.
|
|
2
|
Tap <Manually Acquire>.
|
|
3
|
Specify the IP address, subnet mask, and gateway address (or default gateway).
Specify the settings in the following order: <IP Address>
<Subnet Mask> <Gateway Address>.Enter each setting using the numeric keys, and tap <Apply>.
 |
 |
Checking whether the settings are correctMake sure that the Remote UI screen can be displayed with your computer (Starting Remote UI). If a computer is not available, you can check the connection by using the control panel (Testing the Network Connection).
When you have changed the IP address after installing the printer driverWhen the MFNP port is used, the connection is maintained as long as the machine and the computer belong to the same subnet; therefore, you do not need to add a new port. When the standard TCP/IP port is used, you need to add a new port. Configuring Printer Ports
*If you do not know which port is used, see Checking the Printer Port.
|
Testing the Network Connection
1
Tap <Menu> in the <Home> screen.
2
Tap <Network Settings>.
If a screen for entering a System Manager ID and PIN is displayed, enter the System Manager ID and PIN, tap <Apply>, and press . Setting the System Manager ID (imageRUNNER 2206N / 2006N)
. Setting the System Manager ID (imageRUNNER 2206N / 2006N)3
Select <TCP/IP Settings> <IPv4 Settings> <PING Command>.
<IPv4 Settings> <PING Command>.4
Enter the IPv4 address of another device on the network, and tap <Apply>.
If a proper connection has been established, the result is displayed as shown above.