Finisher (imageRUNNER ADVANCE 715iFZ III/715iZ III/615iFZ III/525iFZ III)

The finisher enables you to use the following functions.

Collate
The printouts are collated into sets arranged in page order of the original.

Group
All printouts of the same original page are grouped together into sets.

Offset
Each printout group is shifted in alternating layers.

Staple + Collate
The printouts are collated into sets arranged in page order and stapled (Corner).

Output tray (Tray C)

The prints are output to this tray. You can specify functions for which the tray is used by configuring <Output Tray Settings>. <Output Tray Settings>

Output tray (Tray B)

The prints are output to this tray. You can specify functions for which the tray is used by configuring <Output Tray Settings>. <Output Tray Settings>

Front cover of the Finisher

Open to clear a staple jam in the stapler unit or replace the staple cartridge.

Right cover of the Finisher

Open this cover when clearing a paper jam inside the finisher. Paper Jams in the Finisher (imageRUNNER ADVANCE 715iFZ III/715iZ III/615iFZ III/525iFZ III)

Selecting the Staple Position

To finish with the stapler, you need to select the staple position paying attention to the orientation of original document.


For the procedure to finish with the stapler, see Finishing with the Stapler.

Stapling at One Location in a Corner of the Paper (Corner)

Refer to the following figures to select the staple position.

Stapling at the top right of paper in portrait orientation

	Feeder		Platen glass

select <Top Right>

Stapling at the top left of paper in portrait orientation

	Feeder		Platen glass

select <Top Left>

Stapling at the top right of paper in landscape orientation

	Feeder		Platen glass

select <Bottom Right>

Stapling at the top left of paper in landscape orientation

	Feeder		Platen glass

select <Top Right>


For information on the paper sizes that can be used for Staple, see Hardware Specifications. To replace the staple cartridge of the stapler unit, see Replacing the Staples (imageRUNNER ADVANCE 715iFZ III/715iZ III/615iFZ III/525iFZ III). For how to clear a paper jam or a staple jam, see Clearing Paper Jams and Clearing Staple Jams (imageRUNNER ADVANCE 715iFZ III/715iZ III/615iFZ III/525iFZ III). Once the output tray reaches its stacking limit while going down or reaches the lower end of travel, printing is suspended. Remove all of the output paper from the tray to resume printing. Collate and group If you select <Offset> in combination with the collate or group function, each printout group is shifted. Staplers When you are using the Staple mode, do not remove the stack of paper from the output tray during the job. Remove the stack of paper when the job has been completed. If the <Load staples into the stapler unit.> message appears, almost all of the staples have been used. To proceed, replace the staple cartridge.

For information on the paper sizes that can be used for Staple, see Hardware Specifications.

To replace the staple cartridge of the stapler unit, see Replacing the Staples (imageRUNNER ADVANCE 715iFZ III/715iZ III/615iFZ III/525iFZ III).

For how to clear a paper jam or a staple jam, see Clearing Paper Jams and Clearing Staple Jams (imageRUNNER ADVANCE 715iFZ III/715iZ III/615iFZ III/525iFZ III).

Once the output tray reaches its stacking limit while going down or reaches the lower end of travel, printing is suspended. Remove all of the output paper from the tray to resume printing.

Collate and group

If you select <Offset> in combination with the collate or group function, each printout group is shifted.

Staplers

When you are using the Staple mode, do not remove the stack of paper from the output tray during the job. Remove the stack of paper when the job has been completed.

If the <Load staples into the stapler unit.> message appears, almost all of the staples have been used. To proceed, replace the staple cartridge.