IMPORTANT
|
It is recommended that the network administrator perform the following procedures.
Use the machine’s control panel if you are configuring the protocol settings for the first time. After configuring the protocol settings, you can change the content by using the Remote UI.
|
1 |
Network Cable Connection (See Chapter 2, “Before You Start Using the Machine,” in the User’s Guide.)
|
Connect the machine to the network using network cables.
|
|
2 |
Interface Settings (Interface Settings (Ethernet Driver))
|
Specify the interface settings for communication between the machine and computers on your network. To specify the settings, use:
The machine’s control panel
The Remote UI (via a web browser)
|
|
3 |
Communication Environment Settings (Communication Environment Settings)
|
Set up a configuration for communication between the machine and computers on your network. To specify the settings, use:
The machine’s control panel
The Remote UI (via a web browser)
|
|
4 |
IEEE802.1X Authentication Settings (IEEE802.1X Authentication Settings)
|
If access to your network requires authentication to a RADIUS server, specify the settings of IEEE802.1X authentication.
|
|
5 |
IP Address Settings (Specifying the Machine’s IP Address)
|
Specify the machine’s network address and establish a connection to a computer on your network. Any of the following can be used to specify the settings:
The machine’s control panel (Additional Functions menu)
The Remote UI (via a web browser)
|
IMPORTANT
|
Sending faxes from a computer is available only when the optional Super G3 Fax Board-AG1 is attached to the machine.
If you are printing from a computer over a TCP/IP network, you can use the following application protocols:
LPD
Raw (Windows 2000/XP/Vista/7/Server 2003/Server 2008 only)
WSD (Windows Vista/7/Server 2008 only)
|
NOTE
|
For details about system requirements, see Printing or Sending a Fax from a Computer.
|
1 |
Connect the machine to a computer
|
Connection via a network
Follow the procedure described in Connecting the Machine to a Network. Connection via a USB cable*
Follow the procedure described in Chapter 1, “Machine Installation,” in the User’s Guide. * In this case, proceed to step 3.
|
|
2 |
Set up the machine according to your network environment (Setting up the Machine for Your Network Environment)
|
Any of the following can be used to specify the settings:
The Machine’s control panel (Additional Functions menu)
The Remote UI (via a web browser)
|
|
3 |
Install drivers in the computer (Setting up a Computer for Printing / Sending a Fax)
|
IMPORTANT
|
To send e-mails or I-faxes with the imageRUNNER 2545W/2535W/2530W/2525W/2520W, the Send function must be activated with the optional Color Send Kit-Y1.
|
NOTE
|
For details about system requirements, see Using E-Mail/I-Fax.
|
1 |
Connect the machine to a network
|
Follow the procedure described in Connecting the Machine to a Network.
|
|
2 |
Set up the machine according to your network environment (Setting up the Machine for Your Network Environment)
|
Any of the following can be used to specify the settings:
The Machine’s control panel (Additional Functions menu)
The Remote UI (via a web browser)
|
IMPORTANT
|
To send data to a file server with the imageRUNNER 2545W/2535W/2530W/2525W/2520W, the Send function must be activated with the optional Color Send Kit-Y1.
|
NOTE
|
For details about system requirements, see Sending Data to a File Server.
|
1 |
Connect the machine to a network
|
Follow the procedure described in Connecting the Machine to a Network.
|
|
2 |
Set up the machine according to your network environment (Setting up the Machine for Your Network Environment)
|
Any of the following can be used to specify the settings:
The Machine’s control panel (Additional Functions menu)
The Remote UI (via a web browser)
|
|
3 |
Set up a file server
|
To send data to an FTP server:
See Setting File Server (FTP). To send data to a shared folder:
See Setting File Server (File Sharing). |