A Message Appears
If a message appears on the operation panel, select the message from the list below, and check how to troubleshoot the problem.
Cannot access the file or folder. Wait a moment and try again, or check the settings from Remote UI. |
|
If the problem persists even after trying the troubleshooting methods, contact your dealer or service representative. If the Problem Persists |
An error occurred during certificate verification.
An error occurred during verification due to an expired certificate or incorrect information.
Install the Correct Key and Certificate or CA Certificate.
Check the expiration date, certification authority, and other information, and then install the key and certificate or CA certificate. Registering a Key and Certificate or CA Certificate Obtained from an Issuing Authority
Are the Current Date and Time on the Machine Correct?
Check the date and time settings on the machine. If the settings are not correct, set the time zone, and then set the current date and time. Setting the Date and Time
Black & White copying is restricted. Only Color copying is available.
Black and white copying is restricted due to Department ID Management.
Log In with a Department ID That Does Not Restrict Black and White Copying.
For the Department ID and PIN, contact the system administrator.
To Cancel Restriction, Change the [Restrict Functions] Setting of Your Department ID.
Log in to Remote UI in System Manager Mode  [Settings/Registration] [User Management] [Department ID Management] select the Department ID to edit clear the [Restrict Black & White Copy] checkbox [OK] |
On the operation panel, select [Menu] in the [Home] screen, and then select [Management Settings] to change the setting. [Department ID Management]
Black & White printing is restricted. Only Color printing is available.
Black and white printing is restricted due to Department ID Management.
Log In with a Department ID That Does Not Restrict Black and White Printing.
For the Department ID and PIN, contact the system administrator.
To Cancel Restriction, Change the [Restrict Functions] Setting of Your Department ID.
Log in to Remote UI in System Manager Mode [Settings/Registration] [User Management] [Department ID Management] select the Department ID to edit clear the [Restrict Black & White Print] checkbox [OK] |
On the operation panel, select [Menu] in the [Home] screen, and then select [Management Settings] to change the setting. [Department ID Management]
Cannot access the file or folder. Wait a moment and try again, or check the settings from Remote UI.
You do not have permission to access the folder, or the user name or password to be used to access the folder is not set correctly.
Set the Correct Path to the Folder.
If Restrict Access is enabled, set the user name and password correctly.
Use Remote UI to display the Address Book, click the applicable destination, and set the information of the shared folder correctly. Registering Destinations to the Address Book (Remote UI)
Cannot analyze the authentication server certificate.
The certificate of the authentication server may not be correct, or it may be a format unsupported by the machine.
Check the Certificate of the Authentication Server, and Change the Setting, as Needed.
Cannot change the destination type of destinations registered to a group.
The selected destination is registered to a group, so you cannot change the destination type.
Delete the Destination from the Group, Change the Destination Type, and Then Register It to the Group Again.
1 | Delete the destination from the group. Deleting Using Remote UI
Deleting Using the Operation Panel
| ||
2 | |||
3 | Register the destination to the group again. Registering Groups to the Address Book (Remote UI) Registering Groups to the Address Book (Operation Panel) |
Cannot find the access point.
An error occurred, preventing the machine from detecting the wireless LAN router (access point).
Is Connection Type Configured Correctly?
Select the connection type (WPS) according to the method supported by the wireless LAN router. Connecting to a Wireless LAN by Using the Router Button (Push Button Mode)
Did You Connect Within the Fixed Time?
When connecting by pressing a button on the wireless LAN router, set the connection type on the operation panel of the machine, and then press the button on the wireless LAN router within one or two minutes. Connecting to a Wireless LAN by Using the Router Button (Push Button Mode)
Are the SSID and Network Key Configured Correctly?
When entering the wireless LAN router information manually, check the SSID and network key of the wireless LAN router, and configure the settings correctly on the machine. Connecting to a Wireless LAN by Setting the Details (Manual Setup Method)
Are the Machine and Wireless LAN Router Located Appropriately?
The machine and wireless LAN router should be installed in a location without walls or other obstructions between the devices and within range of 50 m.
Do not install near a microwave oven, digital cordless telephone, or other device that generates radio waves.
Check the Security Settings of the Wireless LAN Router.
For details, see the manual of the wireless LAN router or contact the manufacturer.
Cannot print. A non-Canon or counterfeit cartridge may be inserted.
Printing cannot be performed due to the use of a toner cartridge whose print quality cannot be guaranteed.
Replace with a New Toner Cartridge.
For optimum print quality, using Canon genuine toner cartridges is recommended. List of Consumables
Cannot print RX data.
Received data cannot be printed for some reason.
Do the Cause and Solution Appear on the Operation Panel?
If so, follow the instructions on the screen.
Is the Front Cover, Rear Cover, or Feeder Cover Open on the Machine?
Close the covers if they are open.
Is Paper Loaded?
Load paper if not loaded. Loading Paper
Is Paper Jammed?
If so, remove any jammed paper. Paper Jams
Have the Toner Cartridges Reached the End of Their Lifetime?
Check the remaining amount of toner in the toner cartridges, and replace any toner cartridges, as needed.
Checking the Remaining Amount of Consumables
Replacing the Toner Cartridges
Checking the Remaining Amount of Consumables
Replacing the Toner Cartridges
Cannot receive the fax. Make sure the fax was sent correctly by the sender.
Operations were not performed within the fixed time when receiving a fax manually, and the machine timed out.
When You Hear a Beep During Fax Reception, Press [Start Receiving] Within 35 Seconds.
[Home] screen on the operation panel [Fax] [Start Receiving] |
Cannot recognize the image.
In Memory Media Print, you selected an image for which a preview cannot be displayed.
Does the Machine Have Sufficient Free Memory?
If the machine does not have sufficient free memory, previews of JPEG and TIFF images cannot be displayed.
Check the faxes received in the memory of the machine, and print or forward them as needed, and delete any unnecessary faxes. Viewing and Printing Faxes Saved in the Memory
Cannot send because more than one destination is specified.
Sending of faxes to multiple destinations is restricted.
To Cancel Restriction, Change the [Restrict Sequential Broadcast] Setting.
Log in to Remote UI in System Manager Mode [Settings/Registration] [TX Settings] [Fax TX Settings] [Edit] in [Restrict Sequential Broadcast], select [Off] [OK] |
On the operation panel, select [Menu] in the [Home] screen, and then select [Function Settings] to change the setting. [Restrict Sequential Broadcast]
Cannot specify group destinations when on-hook.
If you press [Hook] when sending a fax, you cannot specify a group destination.
Specify the destination without pressing [Hook].
Specify the destination without pressing [Hook].
Cannot specify group destinations, or multiple destinations at the same time.
You cannot specify multiple destinations or group destinations when the handset is off the hook.
Return the handset, and then specify the destination.
Return the handset, and then specify the destination.
Cannot use these settings. Sending to the specified destination is restricted.
Sending or saving to a destination registered to a specified favorite setting is restricted due to Department ID Management.
Log In with a Department ID That Does Not Restrict the Sending or Saving Function.
For the Department ID and PIN, contact the system administrator.
To Cancel Restriction, Change the [Restrict Functions] Setting of Your Department ID.
Log in to Remote UI in System Manager Mode [Settings/Registration] [User Management] [Department ID Management] select the Department ID to edit clear the [Restrict Scan] and [Restrict Fax] checkboxes [OK] |
On the operation panel, select [Menu] in the [Home] screen, and then select [Management Settings] to change the setting. [Department ID Management]
Cartridge communication error. Cannot print. A non-Canon or counterfeit cartridge may be inserted.
Printing cannot be performed due to incorrect installation of the toner cartridge, a damaged toner cartridge, or the use of a toner cartridge whose print quality cannot be guaranteed.
Reinstall the Toner Cartridges or Replace with New Toner Cartridges.
For optimum print quality, using Canon genuine toner cartridges is recommended. List of Consumables
If the message still appears after repeatedly reinstalling the toner cartridges, contact your dealer or service representative. If the Problem Persists
Cartridge Communication Error Problems resulting from the use of non-Canon cartridges are not covered under the warranty.
Printing cannot be performed due to incorrect installation of the toner cartridges, a damaged toner cartridge, or the use of a non-Canon toner cartridge, resulting in a communication error.
Reinstall the Toner Cartridges.
For optimum print quality, using Canon genuine toner cartridges is recommended. List of Consumables
If the message still appears after repeatedly reinstalling the toner cartridges, contact your dealer or service representative. If the Problem Persists
Change the authentication password.
The password has expired.
Set a new password.
Set a new password.
Check the authentication settings.
The authentication method set on the machine does not match that set on the RADIUS server.
Check the Authentication Method Set on the RADIUS Server, and Set This Correctly.
Color copying is restricted. Only Black & White copying is available.
Color copying is restricted due to Department ID Management.
Log In with a Department ID That Does Not Restrict Color Copying.
For the Department ID and PIN, contact the system administrator.
To Cancel Restriction, Change the [Restrict Functions] Setting of Your Department ID.
Log in to Remote UI in System Manager Mode [Settings/Registration] [User Management] [Department ID Management] select the Department ID to edit clear the [Restrict Color Copy] checkbox [OK] |
On the operation panel, select [Menu] in the [Home] screen, and then select [Management Settings] to change the setting. [Department ID Management]
Color printing is restricted. Only Black & White printing is available.
Color printing is restricted due to Department ID Management.
Log In with a Department ID That Does Not Restrict Color Printing.
For the Department ID and PIN, contact the system administrator.
To Cancel Restriction, Change the [Restrict Functions] Setting of Your Department ID.
Log in to Remote UI in System Manager Mode [Settings/Registration] [User Management] [Department ID Management] select the Department ID to edit clear the [Restrict Color Print] checkbox [OK] |
On the operation panel, select [Menu] in the [Home] screen, and then select [Management Settings] to change the setting. [Department ID Management]
Copying is restricted.
Copying is restricted due to Department ID Management.
Log In with a Department ID That Does Not Restrict Copying.
For the Department ID and PIN, contact the system administrator.
To Cancel Restriction, Change the [Restrict Functions] Setting of Your Department ID.
Log in to Remote UI in System Manager Mode [Settings/Registration] [User Management] [Department ID Management] select the Department ID to edit clear the [Restrict Color Copy] and [Restrict Black & White Copy] checkboxes [OK] |
On the operation panel, select [Menu] in the [Home] screen, and then select [Management Settings] to change the setting. [Department ID Management]
Could not connect.
An error occurred, preventing the machine from establishing a direct connection.
Wait a Moment, and Try Connecting Again.
If you still cannot establish a connection, restart the machine.
Set the IP Address for Connection to Something Other Than "192.168.22.xx".
The machine must be restarted to apply the settings.
Log in to Remote UI in System Manager Mode [Settings/Registration] [Network Settings] [Direct Connection Settings] [Edit] in [IP Address for Direct Connection], enter the IP address [OK] restart the machine |
On the operation panel, select [Menu] in the [Home] screen, and then select [Preferences] to configure the settings. [Direct Connection Settings]
Is the Subnet Mask Configured Correctly?
Check the IPv4 subnet mask settings. Change the settings if they have not been configured correctly. For details, contact the network administrator.
Viewing the IP address set to the machine
Setting IPv4 Addresses
Viewing the IP address set to the machine
Setting IPv4 Addresses
Could not connect. Check the encryption key.
The network key (encryption key) of the wireless LAN router (access point) is not configured correctly, preventing connection.
Reset the Network Key.
Check the network key of the wireless LAN router, and configure the settings correctly on the machine. Connecting to a Wireless LAN
Could not connect. The maximum number of devices that can connect to the access point has been reached.
The maximum number of devices that can be connected to the wireless LAN router (access point) has been reached, preventing connection.
Reduce the Number of Devices (Clients) Connected to the Wireless LAN Router.
For the maximum number of connections, see the manual of the wireless LAN router or contact the manufacturer.
Could not connect using Easy Connection via PC. The device will restart.
An error occurred, preventing the machine from connecting in Access Point Mode. Alternatively, an error occurred when starting cableless setup mode.
Restart the Machine, and Start Cableless Setup Mode Again.
Administrator privileges are required.
[Home] on the operation panel [Menu] [Preferences] [Network] [Easy Connection via PC] [Yes] start the settings on the computer |
Could not connect using the wireless LAN. Turn the main power OFF and ON, then configure the settings again.
An error occurred, preventing the machine from connecting to the wireless LAN.
Restart the Machine, and Configure the Wireless LAN Connection Again.
Are the Machine and Wireless LAN Router (Access Point) Located Appropriately?
The machine and wireless LAN router should be installed in a location without walls or other obstructions between the devices and within range of 50 m.
Do not install near a microwave oven, digital cordless telephone, or other device that generates radio waves.
Check the Security Settings of the Wireless LAN Router.
For details, see the manual of the wireless LAN router or contact the manufacturer.
Could not connect using WPS. Wait a moment, then configure the settings again.
An error occurred, preventing the machine from establishing a WPS connection.
Wait a Moment, and Configure the Settings Again.
If you still cannot establish a WPS connection, check whether the wireless LAN router (access point) supports WPS.
If It Supports WPS
Check that the machine and wireless LAN router are located appropriately.
The machine and wireless LAN router should be installed in a location without walls or other obstructions between the devices and within range of 50 m.
Do not install near a microwave oven, digital cordless telephone, or other device that generates radio waves.
If It Does Not Support WPS
Connect using a different connection type. Connecting to a Wireless LAN
Could not detect any connections from wireless devices.
An error occurred, preventing the machine from detecting mobile devices.
Did You Connect Within the Fixed Time?
Connect the mobile device to the machine within five minutes of the SSID and network key being displayed.
Could not perform cleaning.
Cleaning could not be performed due to jammed paper, loading of incorrect paper, or another problem.
Load Correct Paper in the Paper Drawer.
Follow the instructions on the operation panel during cleaning, and load usable paper. Loading Paper in the Paper Drawer
Is Paper Jammed?
If so, remove any jammed paper. Paper Jams
Could not perform correction.
Correction could not be performed due to jammed paper, loading of incorrect paper, or another problem.
Load Correct Paper in the Paper Drawer.
Follow the instructions on the operation panel during correction, and load usable paper. Loading Paper in the Paper Drawer
Place the Paper with the Printed Calibration Image on the Platen Glass.
Place the print side of the calibration image face down with the black band at the back of the machine.
Is Paper Jammed?
Remove any jammed paper. Paper Jams
Check the Remaining Amount of Toner in the Toner Cartridges.
A sufficient amount of toner in the toner cartridges is required to perform correction. Check the remaining amount of toner in the toner cartridges, and replace any toner cartridges, as needed.
Checking the Remaining Amount of Consumables
Replacing the Toner Cartridges
Checking the Remaining Amount of Consumables
Replacing the Toner Cartridges
Could not perform IEEE 802.1X authentication. Cannot analyze the authentication server certificate.
Check the certificate of the authentication server, and change the setting, as needed.
Check the Certificate of the RADIUS Server, and Change the Setting, as Needed.
Could not perform IEEE 802.1X authentication. Change the authentication password.
The password has expired.
Set a New Password.
Could not perform IEEE 802.1X authentication. Check the authentication settings.
The authentication method set on the machine does not match that set on the RADIUS server.
Check the Authentication Method Set on the RADIUS Server, and Set This Correctly.
Could not perform IEEE 802.1X authentication. Configure the correct authentication information.
The authentication method or authentication information of IEEE 802.1X is not set correctly.
Set the Authentication Method and Authentication Information (Keys and Certificates, Password, CA Certificate) Correctly.
Could not perform IEEE 802.1X authentication. Configure the information required for authentication.
The authentication method or authentication information of IEEE 802.1X is not set correctly.
Set the Authentication Method and Authentication Information (Keys and Certificates, Password, CA Certificate) Correctly.
Could not perform IEEE 802.1X authentication. No reply from the destination.
The network connection may have a problem.
Check the Network Status and Settings.
Check the Ethernet cable and switch status.
Check the network key of the wireless LAN router, and configure the settings correctly on the machine.
Could not perform IEEE 802.1X authentication. The authentication server certificate has expired.
The server certificate sent from the RADIUS server has expired.
Check the Expiry Date of the RADIUS Server.
Could not perform IEEE 802.1X authentication. The authentication server certificate is incorrect.
A CA certificate that supports the certificate of the authentication server is not registered to the machine.
Check the Certificate Information of the Authentication Server, and Register a Supported CA Certificate.
Setting IEEE 802.1X
Registering a Key and Certificate or CA Certificate Obtained from an Issuing Authority
Registering a Key and Certificate or CA Certificate Obtained from an Issuing Authority
Could not perform Open System authentication. Check the encryption key settings.
The WEP authentication methods of the machine and wireless LAN router (access point) do not match, or MAC address filtering of the wireless LAN router is set to prevent a connection to the machine, thereby preventing Open System Authentication.
Use the Manual Setup Method to Change the WEP Authentication Method to [Shared Key], and Connect Again.
In the MAC address filtering setting of the wireless LAN router, allow the connection to the machine.
Check the MAC address of the machine, and configure the wireless LAN router to allow a connection from that MAC address. Viewing the MAC Address and Connection Information of the Wireless LAN
For the setup method, see the manual of the wireless LAN router or contact the manufacturer.
For the setup method, see the manual of the wireless LAN router or contact the manufacturer.
Could not perform Shared Key authentication. Check the encryption key settings.
The network key (encryption key) of the wireless LAN router (access point) is not configured correctly, or the WEP authentication methods of the machine and wireless LAN router do not match, preventing Shared Key Authentication.
Reset the Network Key.
Check the network key of the wireless LAN router, and configure the settings correctly on the machine. Connecting to a Wireless LAN
Match the WEP Authentication Method on the Machine and Wireless LAN Router.
The machine may be set to Shared Key Authentication, and the wireless LAN router may be set to Open System Authentication. Change the WEP setting according to the authentication method you are using.
When Using Open System Authentication
Connect to the wireless LAN using either of the following methods:
Connect with the access point setup method. Connecting to a Wireless LAN by Searching for a Router (Access Point Setup Method)
Using the Manual Setup Method, connect with the WEP authentication method set to [Open System]. Connecting to a Wireless LAN by Setting the Details (Manual Setup Method)
When Using Shared Key Authentication
On the wireless LAN router, change the WEP authentication method to "Shared Key", and connect again. For the setup method, see the manual of the wireless LAN router or contact the manufacturer.
Direct Connection terminated.
The connection with a mobile device was terminated.
Directly Connect Again.
Easy Connection via PC ended due to timeout The device will restart.
30 minutes have elapsed since the start of the cableless setup mode without connecting to the computer.
Restart the Machine, and Start Cableless Setup Mode Again.
Administrator privileges are required.
[Home] on the operation panel [Menu] [Preferences] [Network] [Easy Connection via PC] [Yes] start the settings on the computer |
End of Cartridge Lifetime
The toner cartridges have reached the end of their lifetime.
It Is Recommended to Replace with New Toner Cartridges.
Press [Display Cartridge Replacement Steps] and replace the toner cartridges while following the instructions on the screen. Replacing the Toner Cartridges
Faxing is restricted.
Faxing is restricted due to Department ID Management.
Log In with a Department ID That Does Not Restrict Faxing.
For the Department ID and PIN, contact the system administrator.
To Cancel Restriction, Change the [Restrict Functions] Setting of Your Department ID.
Log in to Remote UI in System Manager Mode [Settings/Registration] [User Management] [Department ID Management] select the Department ID to edit clear the [Restrict Fax] checkbox [OK] |
On the operation panel, select [Menu] in the [Home] screen, and then select [Management Settings] to change the setting. [Department ID Management]
ITB is near end of lifetime. Replcmt. is not yet needed.
It is nearing the time to replace the transfer belt (ITB) inside the machine.
You can continue use, but you are recommended to contact your dealer or service representative as soon as possible. If the Problem Persists
You can continue use, but you are recommended to contact your dealer or service representative as soon as possible. If the Problem Persists
Load paper.
Correct paper is not loaded.
Is Paper Loaded in the Paper Drawer or Multi-purpose Tray?
Load paper if not loaded. Loading Paper
Are You Using Appropriate Paper When Printing Reports, Lists, and Received Data?
Check that the paper is usable, and replace it with paper to suit your purpose.
Usable Paper
Loading Paper
Usable Paper
Loading Paper
Set the paper size and type correctly according to the loaded paper. Specifying the Paper Size and Type
Low Cartridge Level
It is nearing the time to replace the toner cartridges.
Prepare New Toner Cartridges, and Replace the Old Ones, as Needed.
When printing large printing jobs, it is recommended to press [Display Cartridge Replacement Steps] and replace the toner cartridges while following the instructions on the screen. Replacing the Toner Cartridges
To Continue Printing, Use the Procedure Below.
When Faxing, I-Faxing, or Printing an Auto Report
In the following cases, the data may be saved to the memory of the machine without being printed to prevent printing text that is difficult to read or images that are difficult to see:
When receiving a Fax or I-Fax
When communication results reports are set to be printed automatically (when a message appears for the black toner cartridge)
To continue printing, enable [Continue Printing When Amount in Cartridge Is Low].
Log in to Remote UI [Settings/Registration] [RX/Forwarding Settings] or [RX Settings] [Common Settings] [Edit] in [Common Settings] select the [Continue Printing When Amount in Cartridge Is Low] checkbox [OK] |
On the operation panel, select [Menu] in the [Home] screen, and then select [Function Settings] to configure the settings. [Continue Print. When Cart. Low]
* When this setting is enabled, the printing results may be light or faded.
|
You can manually specify when this message appears (when toner is low). [Display Timing for Cart. Prep.] |
Memory Full (Secure Print)
The memory is full with Secure Print data that has not been printed.
Print the Secure Print Data Saved to the Memory.
For details about how to print, see the procedure for when using the Secure Print function. Step 2: Printing Secure Data by Entering a PIN or Password
Memory Full (Skip Error)
The memory is full with data that has not been printed due to an error.
Cancel Printing of the Data with an Error, or Press [Skip Error] on the [Status Monitor] Screen.
Memory Media Print is restricted.
The settings are configured to not print data from a USB memory device.
To Cancel Restriction, Change the [Memory Media Settings] Setting.
The machine must be restarted to apply the settings.
Log in to Remote UI in System Manager Mode [Settings/Registration] [Store/Access Files Settings] [Memory Media Settings] [Edit] select the [Memory Media Print] checkbox [OK] restart the machine. |
On the operation panel, select [Menu] in the [Home] screen, and then select [Function Settings] to change the setting. [Memory Media Settings]
No reply from the destination.
The Ethernet cable may not be connected or there may be a problem with the switch.
Check the Ethernet cable and switch status.
Check the Ethernet cable and switch status.
No response from the host.
The machine is not connected correctly to the network.
Check the Settings of the Machine and Network, and Connect Again.
When Connected via Wireless LAN
Configure the settings correctly according to your usage environment. Connecting to a Wireless LAN
When Connected via Wired LAN
Check that the Ethernet cable is properly connected. Connecting to a Wired LAN
Paper jammed.
Paper jammed in the machine during printing.
Remove the Jammed Paper, and If Printing Does Not Resume Automatically, Try Printing Again.
Paper Settings and Loaded Size Mismatch
The size of the paper loaded in the machine does not match that set on the operation panel or printer driver.
Match the Size of the Loaded Paper with the Paper Size Setting.
When Using the Loaded Paper
Change the paper size setting on the operation panel to match the size of the loaded paper.
Setting the Paper Size and Type for the Paper Drawer
Setting the Paper Size and Type for the Multi-purpose Tray
Setting the Paper Size and Type for the Paper Drawer
Setting the Paper Size and Type for the Multi-purpose Tray
When printing from a computer, change the paper size setting on the printer driver to match the size of the loaded paper. Printing from a Computer
When Reloading Paper
Load paper of the size set on the operation panel or printer driver. Loading Paper
Check That the Paper Guides Are Aligned with the Markings and Are Not Too Loose or Too Tight.
Paper Drawer  | Multi-purpose Tray  |
Prepare cartridge.
It is nearing the time to replace the toner cartridges.
Prepare New Toner Cartridges, and Replace the Old Ones, as Needed.
When printing large jobs, it is recommended to replace the toner cartridges. Replacing the Toner Cartridges
To Continue Printing, Use the Procedure Below.
When Faxing, I-Faxing, or Printing an Auto Report
In the following cases, the data may be saved to the memory of the machine without being printed to prevent printing text that is difficult to read or images that are difficult to see:
When receiving a Fax or I-Fax
When communication results reports are set to be printed automatically (when a message appears for the black toner cartridge)
To continue printing, enable [Continue Printing When Amount in Cartridge Is Low].
Log in to Remote UI [Settings/Registration] [RX/Forwarding Settings] or [RX Settings] [Common Settings] [Edit] in [Common Settings] select the [Continue Printing When Amount in Cartridge Is Low] checkbox [OK] |
On the operation panel, select [Menu] in the [Home] screen, and then select [Function Settings] to configure the settings. [Continue Print. When Cart. Low]
* When this setting is enabled, the printing results may be light or faded.
|
You can manually specify when this message appears (when toner is low). [Display Timing for Cart. Prep.] |
Printing is restricted.
Printing is restricted due to Department ID Management.
Log In with a Department ID That Does Not Restrict Printing.
For the Department ID and PIN, contact the system administrator.
To Cancel Restriction, Change the [Restrict Functions] Setting of Your Department ID.
Log in to Remote UI in System Manager Mode [Settings/Registration] [User Management] [Department ID Management] select the Department ID to edit clear the [Restrict Color Print] and [Restrict Black & White Print] checkboxes [OK] |
On the operation panel, select [Menu] in the [Home] screen, and then select [Management Settings] to change the setting. [Department ID Management]
Problems resulting from the use of non-Canon cartridges are not covered under the warranty. The amount remaining in the cartridge cannot be displayed correctly.
The remaining amount of toner is not correctly displayed due to the use of a toner cartridge whose print quality cannot be guaranteed.
Replace with a New Toner Cartridge.
For optimum print quality, using Canon genuine toner cartridges is recommended. List of Consumables
Remote scanning is restricted.
Scanning from a computer is restricted due to Department ID Management.
To Cancel Restriction, Change the [Department ID Management] Setting.
Log in to Remote UI in System Manager Mode [Settings/Registration] [User Management] [Department ID Management] [Edit] select the [Allow Scan Jobs with Unknown IDs] checkbox [OK] |
On the operation panel, select [Menu] in the [Home] screen, and then select [Management Settings] to change the setting. [Department ID Management]
Scanning is restricted.
Scanning is restricted due to Department ID Management.
Log In with a Department ID That Does Not Restrict Scanning.
For the Department ID and PIN, contact the system administrator.
To Cancel Restriction, Change the [Restrict Functions] Setting of Your Department ID.
Log in to Remote UI in System Manager Mode [Settings/Registration] [User Management] [Department ID Management] select the Department ID to edit clear the [Restrict Scan] checkbox [OK] |
On the operation panel, select [Menu] in the [Home] screen, and then select [Management Settings] to change the setting. [Department ID Management]
Set the correct authentication information.
The authentication method or authentication information of IEEE 802.1X is not set correctly.
Set the Authentication Method and Authentication Information (Keys and Certificates, Password, CA Certificate) Correctly.
Set the information necessary for authentication.
The authentication method or authentication information of IEEE 802.1X is not set correctly.
Set the Authentication Method and Authentication Information (Keys and Certificates, Password, CA Certificate) Correctly.
Specifying and registering new destinations is restricted.
Destinations that can be specified for sending are restricted to those destinations registered in the Address Book.
To Cancel Restriction, Change the [Restrict New Destinations] Setting.
Log in to Remote UI in System Manager Mode [Settings/Registration] [TX Settings] [Restrict New Destinations] [Edit] clear the [Restrict New Destinations] checkbox [OK] |
On the operation panel, select [Menu] in the [Home] screen, and then select [Function Settings] to change the setting. [Restrict New Destinations]
The authentication server certificate has expired.
The server certificate sent from the RADIUS server has expired.
Check the Expiry Date of the RADIUS Server.
The authentication server certificate is incorrect.
A CA certificate that supports the certificate of the authentication server is not registered to the machine.
Check the certificate information of the authentication server, and register a supported CA certificate.
Setting IEEE 802.1X
Registering a Key and Certificate or CA Certificate Obtained from an Issuing Authority
Registering a Key and Certificate or CA Certificate Obtained from an Issuing Authority
The computer is restricted.
Saving of scanned data to a computer is restricted due to Department ID Management.
To Cancel Restriction, Change the [Department ID Management] Setting.
Log in to Remote UI in System Manager Mode [Settings/Registration] [User Management] [Department ID Management] [Edit] select the [Allow Scan Jobs with Unknown IDs] checkbox [OK] |
On the operation panel, select [Menu] in the [Home] screen, and then select [Management Settings] to change the setting. [Department ID Management]
The encryption key is not set correctly. Check the encryption key settings.
The network key (encryption key) of the wireless LAN router (access point) is not configured correctly on the machine. Alternatively, the WEP authentication method of the machine does not match that of the wireless LAN router.
Reset the Network Key.
Check the network key of the wireless LAN router, and configure the settings correctly on the machine. Connecting to a Wireless LAN
Match the WEP Authentication Method on the Machine and Wireless LAN Router.
The machine may be set to Shared Key Authentication, and the wireless LAN router may be set to Open System Authentication. Change the WEP setting according to the authentication method you are using.
When Using Open System Authentication
Connect to the wireless LAN using either of the following methods:
Connect with the access point setup method. Connecting to a Wireless LAN by Searching for a Router (Access Point Setup Method)
Using the Manual Setup Method, connect with the WEP authentication method set to [Open System]. Connecting to a Wireless LAN by Setting the Details (Manual Setup Method)
When Using Shared Key Authentication
On the wireless LAN router, change the WEP authentication method to "Shared Key", and connect again. For the setup method, see the manual of the wireless LAN router or contact the manufacturer.
The fax number has too many digits.
Sending of a fax cannot be performed because the specified fax number has too many digits.
Specify a Fax Number That Does Not Exceed the Maximum Number of Digits to Send a Fax.
If the settings are configured to send a fax after entering a designated number before you specify a destination registered in the Address Book, the maximum number of digits to send a fax may be exceeded. [Use Addr. Book When On-Hook]
The memory is full. [The memory is full.] Is Displayed on the Operation Panel, and the Operation Cannot Be Performed.
Scanning or faxing cannot be performed due to insufficient available memory. If there is data waiting to be printed or sent, wait until the processing is completed.
Check the Received Faxes Saved in the Memory.
Print or forward them as needed, and delete any unnecessary faxes. Viewing and Printing Faxes Saved in the Memory
When Scanning, Change the Data Size to a Small File Format.
*1 You can skip this step when saving data to a USB memory device. For details about the file formats, see the following: Setting File / Division |
When Saving Scanned Data to a USB Memory Device, Delete Any Unneeded Files from the Device, or Use a Different USB Memory Device.
When Sending Faxes, Divide the Original or Lower the Resolution.
When sending an original with many pages, divide the original and send it.
Change the set resolution to a lower resolution when scanning the original.
[Home] screen on the operation panel [Fax] [TX/RX Settings] tab [Resolution] select the resolution. |
The memory is full. Enter the original type settings again.
Scanning of the original cannot be performed due to insufficient available memory when copying.
To Copy, Change the [Original Type] Setting.
[Home] screen on the operation panel [Copy] [Other Settings] [Original Type] [Text/Photo/Map (Speed)]. |
The memory is full. Scanning will be canceled. Do you want to print?
Reading of the original cannot be performed due to insufficient available memory. Alternatively, all the pages could not be read when sorting and copying.
Divide the Original Before Copying.
Print up to the pages that were read or cancel the job, and then divide the original before copying.
Try Configuring the Setting as Follows.
[Home] screen on the operation panel [Copy] [Other Settings] [Original Type] [Text/Photo/Map (Speed)]. |
The number of entered characters is incorrect or invalid characters are used.
The network key of the wireless LAN router (access point) is not configured correctly on the machine.
Reset the Network Key.
Check the network key of the wireless LAN router, and configure the settings correctly on the machine. Connecting to a Wireless LAN
The USB memory is restricted.
Saving of scanned originals to a USB memory device is restricted.
To Cancel Restriction, Change the [Memory Media Settings] Setting.
The machine must be restarted to apply the settings.
Log in to Remote UI in System Manager Mode [Settings/Registration] [Store/Access Files Settings] [Memory Media Settings] [Edit] select the [Store to Memory Media] checkbox [OK] restart the machine. |
On the operation panel, select [Menu] in the [Home] screen, and then select [Function Settings] to change the setting. [Memory Media Settings]
Use Remote UI to set the information necessary for authentication.
The authentication method or authentication information of IEEE 802.1X is not set correctly.
Check the IEEE 802.1X Setting, and Set This Correctly.
Check the following, and change the setting, as needed. Setting IEEE 802.1X
The login name is specified correctly.
At least one of the following checkboxes is selected: [Use TLS], [Use TTLS], and [Use PEAP].
When using TLS, a key and certificate are registered.
When using TTLS or PEAP, the user name and password are set correctly.