Countermeasures for Each Message

If an error occurs during scanning or printing, or if a problem occurs with the network connection or settings, a message appears on the machine display or the Remote UI screen. For details about each message and solutions to the problems, refer to the messages below. Also, if a six-digit number is displayed when you are logging in, see If a six-digit number is displayed when you are logging in.

23 MEMORY FULL

There is insufficient memory to register overlay forms and external characters, etc.

Cancel printing, initialize the printer to increase the free memory, and then try printing again. However, note that initializing the printer will erase all the print data in the memory of the machine. Custom Settings

Press <Skip Error>, and continue printing. However, the data that could not be registered due to a lack of memory will not be printed.

27 JOB REJECT

The specified emulation does not exist.

Specify emulation that the machine supports.

Press <Skip Error> to skip the printing that an error occurred for. You can perform the following printing.

33 WORK FULL

Could not print because the dedicated work memory was insufficient.

Cancel printing, initialize the printer to increase the free memory, and then try printing again. However, note that initializing the printer will erase all the data in the memory of the machine. Custom Settings

Press <Skip Error>, and continue printing. However, the data for which an error was displayed will not be printed correctly. Also note that registered data such as overlay forms and macros may be deleted.

52 IMAGEMODE REJECT

Data that cannot be processed was sent while printing an image.

Press <Skip Error> to skip the printing that an error occurred for. However, the data for which an error was displayed will not be printed.

Perform printing again using a printer driver that supports the data format of the image.

The Active Directory site information is invalid. Contact the system manager.

The site information of Active Directory is not set correctly.

Check whether [Timing of Site Information Retrieval:] and [Site Access Range:] are set correctly in [Use of Access Mode within Sites:].

Could not verify CRL.

Could not confirm the CA certificate of the certificate authority that issued the certificate revocation list (CRL).

Register the CA certificate of the certificate authority that issued the certificate revocation list (CRL).
Registering a CA Certificate

D1 Replot Buffer Full

Could not redraw because data could not be registered to the replot buffer.

Press <Skip Error>, and continue printing. However, the data that caused the error will not be printed correctly. For information on the replot buffer, see Print.

D1 Div. Print. Bffr Full

Could not perform divided printing because data could not be registered to the buffer for divided printing.

Cancel printing, set <Divide Mode> to <No> and <Enlarge/Reduce> to <Auto> in the HP-GL setup menu, specify the output paper size, and perform printing again. However, the data will be enlarged/reduced when printed. For more details, see Print.

Press <Skip Error>, and continue printing. However, the data that could not be registered will not be printed correctly. For information on divided printing, see Print.

D1 Polygon Buffer Full

Could not draw because data could not be registered to the polygon buffer.

Press <Skip Error>, and continue printing. However, the data that could not be registered will not be printed correctly. For information on the polygon buffer, see Print.

D0-nn error (nn is two alphanumeric characters)

The printer stopped operating normally due to an unknown problem.

Restart the machine. Press the power switch to turn OFF the machine (Shutting Down the Machine). When 10 or more seconds have elapsed after the main power indicator turned off, turn ON the machine again (How to Turn ON the Main Power). If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.

FF FONT FULL

Could not register font information in the font table because there were too many fonts to register.

Press <Skip Error>, and continue printing. However, the data that could not be registered will not be printed correctly.

FM DL SIZE ERROR n (n is a single alphanumeric character)

The printer stopped operating normally due to an unknown problem.

Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.

FM DL SCALE ERROR n (n is a single alphanumeric character)

The printer stopped operating normally due to an unknown problem.

Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.

FM DL FONT MEMORY FULL

The printer stopped operating normally due to an unknown problem.

Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.

FM FILE ACCESS ERROR

The printer stopped operating normally due to an unknown problem.

Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.

FM SC WORK MEM. ERROR n (n is a single alphanumeric character)

The printer stopped operating normally due to an unknown problem.

Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.

FM ALIGNMENT ERROR

The printer stopped operating normally due to an unknown problem.

Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.

FM FONT PARSE ERROR

The printer stopped operating normally due to an unknown problem.

Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.

FM FONT MEMORY FULL

The printer stopped operating normally due to an unknown problem.

Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.

FM WORK MEMORY ERROR

The printer stopped operating normally due to an unknown problem.

Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.

IEEE 802.1X error. Set the correct authentication information.

The client authentication information is not set correctly.

Check whether the authentication method and authentication information (key and certificate, user name and password, and CA certificate) are set correctly.

IEEE 802.1X error. No reply from the destination.

An error occurred while communicating with the authenticator.

Check whether the authenticator (LAN switch) and RADIUS server are set correctly.

IEEE 802.1X error. Cannot analyze the certificate.

Failed to analyze the server certificate sent from the RADIUS server.

Check the content of the server certificate of the RADIUS server.

IEEE 802.1X error. The certificate is incorrect.

An error occurred when using the server certificate sent from the RADIUS server as a CA certificate for validation.

Check the content of the server certificate of the RADIUS server and the CA certificate registered in the machine.
Registering a CA Certificate

IEEE 802.1X error. The certificate has expired.

The server certificate sent from the RADIUS server has expired.

Check the expiration date of the server certificate of the RADIUS server.

IEEE 802.1X error. Change the authentication password.

The password has expired.

Set a new password.

IEEE 802.1X error. Check the authentication settings.

The authentication method set in the machine and the authentication method set in the RADIUS server do not match.

Check the authentication method set in the machine and the RADIUS server, and set the correct authentication method.

Set the IP address.

The IP address of the machine is not set.

Set the IP address in <TCP/IP Settings>, and restart the machine.

Cannot set PDF (Format to PDF/A) as default. All other settings have been set.

You tried to register a default value for <Access Stored File>, while the <Format PDF to PDF/A> settings for the <PDF> file format was changed.

You cannot register default settings if you change the <Format PDF to PDF/A> setting for the <PDF> file format. Register default settings after changing settings other than the <Format PDF to PDF/A> setting.

Check the server name in the SMB server settings.

A computer or printer with the same name as the SMB server is registered in the WINS database.

If <WINS Resolution> is set to <On> in <WINS Settings>, do not register a computer or printer with the same name as the SMB server in <Computer Name/Workgroup Name Settings> in <TCP/IP Settings>.

A computer or printer with the same name as the SMB server exists in the workgroup that the machine belongs to.

Do not register a computer or printer with the same name as the SMB server in <Computer Name/Workgroup Name Settings> in <TCP/IP Settings>.

TLS Error

The WebDAV server does not support TLS encrypted communication.

Set TLS on the WebDAV server side, according to your environment.

The proxy server does not support TLS encrypted communication.

If the WebDAV client connects to the internet via a proxy, set TLS on the proxy server side.

Cannot delete the default key because it is in use by TLS or other settings. Check the settings.

The key and certificate you are trying to delete is being used in TLS encrypted communications or the Restrict Receiving for Each Function mode of Device Information Distribution.

Set all TLS settings to <Off> to stop TLS encrypted communication. Also set all settings in <Restrict Receiving for Each Function> to <On>.
<Device Information Distribution Settings>

TCP/IP Error

Could not automatically retrieve the address with DHCP and Auto IP.

If the address cannot be automatically retrieved with DHCP and Auto IP, <IP Address> in <IPv4 Settings> is set to 0.0.0.0. Set the correct IPv4 address.

0.0.0.0 is set as a fixed IPv4 address in <IP Address> in <IPv4 Settings>.

Set the correct IPv4 address.

The IPv6 address is not set correctly.

Check the following. It may take several minutes until the stateless address is decided.

Check whether <Use IPv6> is set to <On> in <IPv6 Settings>.

When using a stateless address or DHCPv6, check whether each address has been retrieved.

If the address has not been retrieved, check the settings of the router and the DHCPv6 server.

The address of the DNS server is not set correctly.

Check whether the address of the DNS server is set correctly in <IPv4> or <IPv6>.

Could not send to the TCP/IP protocol stack.

Check whether the IPv4 address or IPv6 address is set correctly in <IPv4 Settings> or <IPv6 Settings>.

Out of resources. Wait a moment, then try again.

TCP/IP resources were insufficient while continuously sending or after continuously sending with FTP or Windows (SMB).

Try again after waiting a while.

Check the TCP/IP.

The TCP/IP of the machine is not operating.

Check the IP address, DHCP, and Auto IP settings in <TCP/IP Settings>.

Check the TCP/IP. (Main Line)

The IP address of the main line is set to "0.0.0.0".

Set a different IP address.

Check the wired LAN adapter connected to the USB port.

Multiple USB-LAN adapters are connected, or the USB-LAN adapter is not connected/recognized.

Check the connection of the USB-LAN adapter.

If you reconnected the USB-LAN adapter, restart the machine.
Front Side

XPS Print Range Error

There are no pages that can be processed in the specified range for printing.

Specify a correct page range.

XPS Image Data Error

Failed to extend the image data.

Replace the image data in the XPS file and try printing again.

XPS Spool Memory Full

There is insufficient memory to process the XPS data.

Restart the machine and try printing again. If you still cannot print, divide the pages into multiple files and print them separately.

XPS Data Error

An invalid command is specified due to corrupt data, etc. and processing cannot continue.

Perform printing again using XPS data in a format supported by the machine.

XPS Unsupport Image Err

An unsupported data format is included.

Convert the data to the TIFF or JPEG format and try printing again.

XPS Font Error

Failed to analyze the font data.

Replace the font data in the XPS file and try printing again.

XPS Page Data Error

Cannot generate pages because the descriptions are incorrect.

Perform printing again using XPS data in a format supported by the machine.

XPS Memory Full

There is insufficient memory to process the XPS data.

Press <Skip Error>, and continue printing. However, pages that include the data that caused the error may not be printed correctly.

You do not have privileges to access the XXX page.

You tried to log in as a user without the required privileges.

The account has expired. Contact the system manager.

The certificate may have expired.

Confirm the expiration date of for the certificate registered in the machine. If the certificate has expired, register a certificate within the validity period.
Registering a Key and Certificate for Network Communication

The expiration date of the account has expired.

Confirm the expiration date of the corresponding account.

Cannot start this application because system resources (memory, threads, sockets, file descriptors, disk space, or screen size) required to start the application may not be available. <Resources>

The application cannot be used because the required system resources, such as memory and disk space, may not be able to be secured.

You may be able to use the desired application by closing other applications.

Cannot download application logs because application logs do not exist.

The application log does not exist.

The operation cannot be performed because the log does not exist. Use the [Back] button to return to the previous page.

The contents of the file for the application to install are incorrect or information is missing. Check the file.

The application could not be installed because the content of the specified file is invalid or information is insufficient.

An application cannot be installed if the content of the file is invalid. Check the content of the file, and if there is no problem, contact the developer of the application or the support department for the application.

The contents of the file for the license to install are incorrect or information is missing. Check the file.

The license file could not be installed because the content of the specified file is invalid or information is insufficient.

A license file cannot be installed if the content of the file is invalid. Check the content of the file, and if there is no problem, contact the developer of the application or the support department for the application.

Could not delete application logs because an error occurred.

The log could not be deleted because an unknown error occurred.

Use the [Back] button to return to the previous page.

Could not download application logs because an error occurred.

The log could not be downloaded because an unknown error occurred.

Use the [Back] button to return to the previous page.

Could not delete authentication information because an error occurred.

The authentication information could not be deleted because an unknown error occurred.

Contact your dealer or service representative.

Could not set authentication information because an error occurred.

The authentication information could not be set because an unspecified error occurred.

Contact your dealer or service representative.

An error occurred. Contact the system manager.

The selected user has already been deleted.

An unexpected system error occurred.

Check the operations and log in again. If you still cannot log in, consult your system administrator.

No response.

The machine is not connected to the network correctly.

Check the machine and network settings, and try connecting again.
Setting up the Network Environment

The waste toner is nearly full. Replacement is not yet needed.

The waste toner container is almost full.

You can continue printing for a while, but you should have a new one available so that you can make replacement as soon as it is needed. If you decide to replace the waste toner container at the time when this message is displayed, press the icon at the bottom right of the screen to display a motion video to give the instructions for waste toner container replacement. Follow these instructions to replace the waste toner container.

Replace waste toner container.

The waste toner container is full.

Follow the instructions on the screen to replace the waste toner container.

Insert the waste toner container.

The waste toner container is not properly set.

Follow the instructions on the screen to set the waste toner container.

Cannot recall the settings because the function for the button does not exist.

A personal button or shared button that includes a function not supported by the machine was used.

If you have imported personal buttons/shared buttons registered in another imageRUNNER ADVANCE series device, buttons not supported by the machine may be included. Register the personal buttons/shared buttons again in the machine.

Cannot recall the settings because the function for the button is disabled. Enable the function, then try again.

The operation could not be executed by pressing the button because the function to use has been stopped.

Press the button after enabling the function that was stopped to be used.

Synchronize Custom Settings: Log in again for synchronization.

There is an inconsistency between the synchronization data of the server machine and that of the client machine synchronizing custom settings.

Log out, and then log in again.

Synchronize Custom Settings: Some settings are restricted.

The client machine was synchronizing custom settings, but the server machine is turned OFF or is not operating normally.

Turn the server machine ON.

If the server machine is operating normally, check that its network cable is connected before checking the network settings.


Data may not be able to be synchronized correctly while this message is displayed, but can be synchronized after the problem is resolved.

Synchronize Custom Settings: An error occurred.

An error occurred during synchronization startup.

Confirm that the address of the destination server is correct for the synchronization of custom settings (client).

If the synchronization of custom settings (client) is complete, restart synchronization.

Restart the machine.

If the problem is not resolved even after restarting the machine, check the followings.

1. You can ping the IP address set for the destination

2. The address of the destination server is correctly displayed

Synchronize Custom Settings: Enabling synchronization...

Processing to begin synchronization of custom settings is being performed.

Wait until processing is complete.

Synchronize Custom Settings: Server authentication error.

Authentication with the server machine could not be achieved.

Check that the authentication user ID and new password for the synchronization of custom settings (client) are the same as the authentication user ID and password with administrator privileges in the server machine.

If the synchronization of custom settings (client) is complete, restart synchronization.

Restart the machine.

Synchronize Custom Settings: Cannot find the server.

The server machine for synchronization of custom settings could not be found using Auto Search.

Confirm that the server machine is turned ON.

If the server machine is operating normally, check that its network cable is connected before checking the network settings.

Confirm the usable conditions for Auto Search. Starting Setting Synchronization

Without using Auto Search, manually specify the server address of the destination for the synchronization of custom settings (client), and the search depth (router).

If the synchronization of custom settings (client) is complete, restart synchronization.

Restart the machine.

Synchronize Custom Settings: Cannot identify the server.

Multiple server machines for the synchronization of custom settings were found using Auto Search.

Manually specify the server machine or shut down all unnecessary server machines that are currently running so that only one remains.

When specifying the server machine manually

Without using Auto Search, manually specify the server address of the destination for the synchronization of custom settings (client), and the search depth (router). Starting Setting Synchronization

When shutting down unnecessary servers that are currently running

Even if the network settings of the server machine include both IPv4 and IPv6, if IPv6 is prioritized and the client machine disables IPv6, the client machine cannot connect via search. Enter the IPv4 address for the destination server address.

If the synchronization of custom settings (client) is complete, restart synchronization and then restart the machine.

Check the covers.

The cover of optional equipment is open.

Check whether the covers of optional equipment are closed.

An error occurred when auto exporting the audit log.

The data could not be exported because a server error occurred.

Check that the server is functioning normally.

The machine is not connected to the network correctly.

Check the settings of the machine and the network, and try connecting again.

The automatic export settings are incorrect.

Check that the automatic export settings are correct (Exporting Logs Automatically).

The function may be stopped. Buttons could not be imported.

When importing data, buttons with functions not supported by the machine were included.

Check whether all the buttons have been imported to the machine.

Routing registration failed. Check Static Routing Settings.

There is an entry that routing table registration failed for in the static routing settings.

Check the registered destination address and gateway address, and specify the correct settings.

The device is currently being used by another user. Wait a while, and then try to perform the operation again.

You cannot use the machine when it is being used by another user.

Try again after waiting a while.

An error occurred when verifying.

The certificate is invalid.

Register the correct certificate and specify the settings again.
Configuring the Key and Certificate for TLS
Registering a Key and Certificate for Network Communication

This CRL is invalid.

The certificate revocation list (CRL) may be corrupt, or a signing algorithm not supported by the machine may be used.

This CRL has expired.

The start date for the certificate revocation list (CRL) may be set to a date in the future.

Check the start date of the certificate registered in the machine. If the start date is set to a date in the future, use the certificate on a day after that date.
Registering a Certificate Revocation List (CRL)

The date and time set on the machine may be incorrect.

Check the date and time setting of the machine.
Setting the Date/Time

This application does not support the security policy function.

The MEAP application you tried to start may not operate according to the security policy settings of the machine.

Check the security functions of the application to see whether it can be used.

Cannot register because the algorithm of this key is not supported.

You tried to register the key and certificate file of an unsupported encryption algorithm.

Register the key and certificate file of a supported encryption algorithm.
Registering a Key and Certificate
System Specifications

Cannot set as the default key because this key is corrupted or invalid.

The key specified for the machine cannot be set because it is corrupted.

This certificate has been revoked.

The certificate is included in the certificate revocation list (CRL).

This certificate is invalid.

The certificate is invalid.

Register the correct certificate and specify the settings again.
Configuring the Key and Certificate for TLS
Registering a Key and Certificate for Network Communication

This certificate has expired.

The certificate may have expired.

Check the expiration date of the certificate registered in the machine. If the certificate has expired, register a valid certificate.
Registering a Key and Certificate for Network Communication

The date and time set on the machine may be incorrect.

Check the date and time setting of the machine.
Setting the Date/Time

Cannot print this job.

The job was canceled because there are too many sheets to staple.

Check the maximum number of sheets of paper that can be stapled together, and execute the job again.

You can specify the procedure to perform when there are too many sheets to staple at once.
<Action When Too Many Sheets to Staple>

The specified application cannot be installed on this device.

You cannot install applications other than Enhanced System Applications.

Specify the application to install again.

No response from the server. Check the settings.

The specified server may have a problem such as not being specified correctly, not being turned on, or having insufficient resources.

Try specifying the server again after waiting a while. If there is still no response from the server, select another server.

Check the server.

You tried to access the server without using a proxy.

Check whether the WebDAV server settings are correct.

Check whether the proxy settings are correct.
Setting a Proxy

Access to the destination is not allowed.

Check whether the WebDAV server settings are correct.

The proxy server failed to communicate with an upstream server.

Check whether the WebDAV server and proxy server settings are correct.

An HTTP protocol version not supported by the WebDAV server was used in a request from the WebDAV client.

Check whether the WebDAV server settings are correct.

The disk space of the WebDAV server is insufficient for the request from the WebDAV client.

Make sufficient disk space for the request available on the WebDAV server.

The appropriate paper size, A4, is not available.

Paper of the optimal size selected with Automatic Paper Selection has not been loaded.

Load paper of the displayed size.

<Paper Source Auto Selection> is set to <Off>.

Specify the paper drawer manually.

Set a paper source loaded with the optimal paper size to <On> in <Paper Source Auto Selection>.
<Paper Source Auto Selection>

Paper of a type that cannot be selected with Automatic Paper Selection is loaded.

Specify the paper drawer manually.

Sub line was disconnected due to a subnet mask conflict.

The network addresses of the main line and sub line conflict.

Check the IP address and subnet mask settings of the main line and sub line.

There are too many subdirectories.

The maximum number of characters was exceeded because the number of levels was too deep.

The destination cannot be specified. Specify another destination.

Remove all the output paper.

Paper has accumulated in the output tray.

Remove all paper from the output tray.

Cannot install this application because an applet included in the specified application has exceeded the area that can be displayed in the device panel.

The application could not be installed because its applet exceeds the area that can be displayed on the screen of the machine.

Install the applet for an application that can fit in the display area of the machine.

The following information is missing in file for the specified application. Check the file. <Missing information>

The application cannot be installed because the required information is not included in the file.

The specified application does not support this device.

The specified application cannot be installed to the machine.

Some applications can only be installed to certain devices. Install an application that is supported by the machine.

The contents of the specified file are incorrect or information is missing. Check the file.

The specified file is not a license file.

Check whether the specified file is a license file.

The specified file contains insufficient information.

Check the content of the file.

Cannot find the specified application. It may have been uninstalled by another user.

The specified application is not installed to the machine.

Use the [Back] button to return to the previous page.

The contents of the specified file may be incorrect.

You tried to register a button by specifying a different file when importing.

The specified license does not match this device. Specify an installable license.

The specified license file cannot be installed to the machine.

Specify a license file that can be installed.

The default key is not set. Check TLS Settings.

The key and certificate (TLS server certificate) are not registered.

To use TLS encrypted communication, first register the key to be used.
Configuring the Key and Certificate for TLS

The default key is not set. Check the Key and Certificate List settings in Certificate Settings.

The key and certificate (TLS server certificate) are not registered.

Register a key and certificate for performing TLS encrypted communication.
Generating the Key and Certificate for Network Communication
Registering a Key and Certificate

The combination of the allowed version and selected algorithm is inappropriate. Enter settings again.

The selected settings cannot be used together.

Set a valid combination.
Configuring the Key and Certificate for TLS

Cannot print because the ambient temperature is too low.

The temperature in the machine’s environment is less than 10°C.

Adjust the temperature of the environment to a suitable temperature.

A wired LAN adapter that cannot be used has been connected.

A USB-LAN adapter that cannot be used with the machine is connected.

For information on the USB-LAN adapters that can be used, contact your dealer or service representative.

Could not verify the certificate.

The CA certificate of a certificate authority could not be confirmed.

The upper (lower) ionizer of the static eliminator needs to be cleaned.

The ionizer of the Static Eliminator is dirty.

Your dealer or service representative is automatically notified of this message.

Static eliminator upper (lower) ionizer needs cleaning. Call dealer/serv rep

The ionizer of the Static Eliminator is dirty.

Contact your dealer or service representative.

Clean the upper (lower) ionizer of the static eliminator.

The ionizer of the Static Eliminator is dirty.

Clean the ionizer.

The upper (lower) ionizer of the static eliminator needs to be checked.

The ionizer of the Static Eliminator may be malfunctioning.

Your dealer or service representative is automatically notified of this message.

Static eliminator upper (lower) ionizer needs check. (Call dealer/serv. rep.)

The ionizer of the Static Eliminator may be malfunctioning.

Contact your dealer or service representative.

The static eliminator needs to be checked.

An error has occurred in the high-voltage components of the Static Eliminator.

Your dealer or service representative is automatically notified of this message.

The static eliminator needs to be checked. (Call dealer/service rep.)

An error has occurred in the high-voltage components of the Static Eliminator.

Contact your dealer or service representative.

The internal storage needs to be replaced. (Call service rep.)

The storage device has failed. Alternatively, a storage device is not installed.

Contact your dealer or service representative.

Remove the paper from the booklet tray.

Paper remains in the booklet tray.

Remove the paper remaining in the booklet tray. Printing starts automatically.

Cannot connect.

Failed to perform proxy authentication.

Check whether the proxy settings are correct.
Setting a Proxy

Cannot edit/delete the paper because it is being used for other settings in Settings/Registration.

You tried to edit or delete paper that was registered in another setting via <Paper Type Management Settings>.

The paper is set as a target for automatic gradation adjustment. To edit or delete paper via <Paper Type Management Settings>, it is necessary to set another type of paper as a target for correction and perform gradation correction again.
Adjusting Gradation

Check Computer Name in Settings/Registration.

A computer or printer with the same name is registered in the WINS database.

When <WINS Resolution> in <WINS Settings> is set to <On>, do not register a computer or printer with a name already listed in <Computer Name/Workgroup Name Settings> in <TCP/IP Settings>.

A printer or computer with the same name already exists in the same workgroup as this machine.

Do not register a computer or printer with a name already listed in <Computer Name/Workgroup Name Settings> in <TCP/IP Settings>.

An error occurred in the sensing unit.

A scanning error occurred in the sensing unit.

Clean the scanning area. Cleaning the Scanning Glass of the Sensing Unit-B (Optional)

Cannot change the settings because the selected key is being used.

The key and certificate you are trying to delete is being used in TLS encrypted communications or the Restrict Receiving for Each Function mode of Device Information Distribution.

Set all TLS settings to <Off> to stop TLS encrypted communication. Also set all settings in <Restrict Receiving for Each Function> to <On>.
<Device Information Distribution Settings>

Cannot find the selected server. Check the settings.

The IP address could not be identified.

Check whether the settings in <DNS Settings> are correct.

Check whether the settings on the DNS server side are correct.

Cannot connect to the selected server. Check the settings.

Could not connect to the IP address/port.

Check whether the gateway address set in <TCP/IP Settings> is correct.

The setting item specified from Settings Menu cannot currently be used. Contact the system manager.

The selected settings menu cannot be changed or is not available.

Contact your system administrator.

The selected button may be unavailable. Contact the system manager.

The selected user does not exist.

"Administrator" has been disabled.

Select a user with administrator privileges.

Session timed out. Wait a moment, then try to access the database again.

The session timed out because the specified length of time elapsed.

Try accessing again after waiting a while. If the session continues to time out, restart the machine.

Could not execute because the file contains unsupported data.

The page cannot be generated due to incorrect content.

Try printing again using data in a format compatible with the machine.

Direct Connection: Ended due to an error.

Failed to connect to the mobile device, or no data was sent or received between the machine and the connected mobile device for a certain period of time.

Check the connection between the machine and the mobile device.

Direct Connection: Ended because no other device could be found.

Cannot find a mobile device capable of connection.

Check the network settings of the mobile device, and then connect by holding it near the machine. Depending on your mobile device, the machine may not operate correctly. If you cannot successfully connect, contact your dealer or service representative.

Adjusting gradation... Wait a moment.

The machine is performing auto adjustment.

Printing will automatically resume when the adjustment is complete. Wait a while.

Could not access the database. Restart the device.

Failed to access the user database because it is corrupt, etc.

Restart the machine.

The cleaning web is nearly low. (Printing possible.)

The replacement time for the displayed cleaning web unit is due.

Prepare a cleaning web unit.

Replace the cleaning web unit. (Printing possible.)

The cleaning web of displayed number is low. Printing will become not possible soon.

Prepare a cleaning web unit. When printing a large amount, it is recommended to replace the cleaning web unit. Replacing the Cleaning Web Unit

Replace the cleaning web unit.

Printing cannot be done, because the cleaning web of displayed number is out.

Replace with a cleaning web. Replacing the Cleaning Web Unit

Certificate Expiration Date Error

The certificate has expired.

Check the expiration date of the certificate.

Cannot log in because multiple users are registered under the same user name. Contact the system manager.

The user name could not be distinguished because user names are set to be not case-sensitive.

Change the settings to make user names case-sensitive, or register another user name.

Cannot register any new buttons because the number of registered buttons has reached the limit. Buttons already registered can be overwritten.

The button cannot be registered because the maximum number of buttons has been exceeded.

Overwrite an existing button or delete unnecessary buttons.
Customizing the <Home> Screen

Cannot import because the number of buttons for registration has exceeded the upper limit.

Buttons cannot be registered while importing because the maximum number of personal buttons/shared buttons has been exceeded.

Delete unnecessary personal buttons/shared buttons, and import the data again.

Could not register because the number of registered users has reached the limit.

Cannot register the user because the number of users has exceeded the upper limit.

Delete any unnecessary users.

Could not retrieve the device information details. Do you want to register the device as a destination?

Could not connect with the client machine due to an unknown reason when registering the destination client machine for distributing device information.

Check whether the client machine is turned ON.

Check the client machine and network settings, and try connecting again.
Setting up the Network Environment

Set the key and certificate to use for TLS in the client machine.
Configuring the Key and Certificate for TLS

Set a setting in <Restrict Receiving for Each Function> to <Off> in the client machine.
<Device Information Distribution Settings>

Set <Use HTTP> to <On> in the client machine.
<Use HTTP>


If you select <Yes> in the above message, the client machine will be registered with <Distributable Settings> blank in <Details>, but device information cannot be distributed.

Replace the toner cartridge. (XXXX)

The toner in the toner cartridge has run out.

Pressing the icon displayed at the bottom right of the screen displays a motion video to give the instructions for toner cartridge replacement. Follow these instructions to replace the toner cartridge.


The "XXXX" in the message indicates the toner color. When black toner has run out completely, it is not necessary to press the icon on the lower-right corner of the screen. The toner cartridge replacement screen is automatically displayed, which allows you to perform the replacement procedure in accordance with the instructions given by motion video.

The toner cartridge can be replaced. (XXXX)

Toner in the toner cartridge is running out.

You can continue printing, but at this time you should prepare a new toner cartridge to have it available when needed.


This message may not be displayed depending on your contract. The "XXXX" in the message indicates the toner color. When <Display Remaining Toner Error Message> is <On>, <Maintenance Notice> is displayed. If you press <Close>, the message will disappear. But if the machine returns from the sleep mode or the main power of the machine is turned ON, the message will be displayed again. To clear this message, (Settings/Registration) → <Preferences> → <Display Settings> → <Delete Remaining Toner Error> → Press <Yes>.

This message may not be displayed depending on your contract.

The "XXXX" in the message indicates the toner color.

When <Display Remaining Toner Error Message> is <On>, <Maintenance Notice> is displayed. If you press <Close>, the message will disappear. But if the machine returns from the sleep mode or the main power of the machine is turned ON, the message will be displayed again. To clear this message,

(Settings/Registration) → <Preferences> → <Display Settings> → <Delete Remaining Toner Error> → Press <Yes>.

Replace the toner cartridge. (XXXX)

The toner in the toner cartridge has run out.

There is a little toner left in the machine, but printing will soon be impossible. Press the icon at the bottom right of the screen to display a motion video to give the instructions for toner cartridge replacement. Follow these instructions to replace the toner cartridge.


The "XXXX" in the message indicates the toner color.

Cleaning the drum... Wait a moment.

The machine is cleaning the drum.

Printing will automatically resume when the adjustment is complete. Wait a while.

Load staples into the saddle stitch unit.

There are no staples in the staple case in the finisher's saddle stitch unit.

Replenish the staples (replace the staple case).
Maintenance

The entered PIN is incorrect.

An incorrect PIN was entered.

Enter the PIN again.

If you do not know the correct PIN, contact the administrator.

The authentication server is not running. Contact the system manager.

The LAN cable is disconnected.

Connect the LAN cable.

The Active Directory server is not running.

Start the Active Directory server.

The KDC service of Active Directory is stopped.

Follow the procedure below to check the status of the service.

1. Start the "Service" management tool of Active Directory.

2. Check whether the Active Directory server is operating normally.

Communication with the Active Directory*server is blocked by the firewall.

Stop blocking the default port 88.

* If Active Directory is set as the login destination, communication is normally performed with the UDP protocol using port 88, but the data may be processed with the TCP protocol if it exceeds a certain size.

Cannot find the authentication server. Contact the system manager.

The LAN cable is disconnected.

Connect the LAN cable.

The primary/secondary DNS server settings of the machine are incorrect or not set.

Check and adjust the DNS server settings of the machine.

The DNS server specified in the machine is not running or its service is stopped.

Follow the procedure below to check the status and settings of the DNS server.

1. Check whether the DNS server specified in the machine is running.

2. Start the "Service" management tool of the DNS server.

3. Check the status in [DNS Server], and if [Enable] is not displayed, right-click and select [Enable].

Check whether the host record exists in the DNS server.

Check whether a host record exists in the DNS server, and whether the forwarder settings are correct.

No password is set on the authentication server side. Contact the system manager.

An appropriate password was not set on the server side when configuring or upgrading Active Directory.

Reset the password of the corresponding account, and specify the settings again.

The account information necessary to log in to the authentication server is invalid. Contact the system manager.

The user name or password is not set correctly.

Confirm the authentication user ID and password, and whether the user has administrator privileges.

The attributes specified in the server settings are not set correctly.

Confirm that the attributes are correct. Also, make sure that the fields (attribute names) do not contain invalid values.
Registering Server Information

The administrator account information specified in the server settings is not set correctly. Alternatively, the user could not log in as an administrator.

Specify the correct administrator account information.

The information for the server settings is insufficient.

Confirm that the attributes necessary for logging in are set correctly.
Registering Server Information

A competing IP address was found on the network.

The IPv4 address set for the machine already exists in the same network as the machine.

Change the IP address of the machine in <IP Address> in <IPv4 Settings> so that it does not conflict with the IP address of another device.

Check the network connection.

The cable is not connected to the machine correctly.

Check whether the LAN cable is connected correctly. If you had to connect it again, restart the machine.
Connecting to a Wired LAN

The machine is not connected to the network.

If you want to use the machine without connecting to a network, set <Confirm Network Connection Setting Changes> to <Off>.
<Confirm Network Connection Setting Changes>

Check the network connection. (Main Line)

The machine and the LAN cable of the main line are not connected correctly.

Check whether the LAN cable is connected correctly. If you had to connect it again, restart the machine.
Connecting to a Wired LAN

The machine is not connected to the network.

If you want to use the machine without connecting to a network, set <Confirm Network Connection Setting Changes> to <Off>.
<Confirm Network Connection Setting Changes>

Check the network connection. (Sub Line)

The machine and the LAN cable of the sub line are not connected correctly.

Check whether the LAN cable is connected correctly. If you had to connect it again, restart the machine.
Front Side

The machine is not connected to the network.

If you want to use the machine without connecting to a network, set <Confirm Network Connection Setting Changes> to <Off>.
<Confirm Network Connection Setting Changes>

Check the punch waste tray.

The punch waste tray in the finisher is full.

Empty the punch waste tray.
Maintenance

The alignment function of the finisher needs to be checked. Contact your service representative. Printing is still possible.

The paper alignment function of the finisher is broken.

Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.

Output the paper to a tray with a working paper alignment function.
<Output Tray Settings>

The finisher output trays cannot move up or down.

The output tray of the finisher is not operational.

Remove any objects that may be obstructing the operation of the output tray.

Restart the machine. If the message does not disappear after restarting the machine, write down the message displayed and contact your dealer or service representative.

The front cover of the finisher is open.

Check whether the front cover of the staple finisher/booklet finisher is closed.

Cannot register any more forms.

The maximum number of registered image forms for the Superimpose Image mode has been reached.

Delete any unnecessary image forms and try registering again.

Cannot log in because an authentication error occurred in Department ID Management. Contact the system manager.

When using User Authentication, Department ID Management is enabled but Department IDs have not been assigned to users.

If you are a general user, ask your administrator to assign you a Department ID.

If you are an administrator user, ask the Department ID Management administrator to assign you a Department ID. If no administrator users can log in, contact your dealer or service representative.

PDL Invalid DLG Input

The printer stopped operating normally due to an unknown problem.

Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.

PDL DLG Rendering Error

The printer stopped operating normally due to an unknown problem.

Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.

PDL DLG Unknown Error

The printer stopped operating normally due to an unknown problem.

Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.

PDL DLG Memory Full

The work memory was insufficient when the system was processing data (in particular, graphic processing and text processing).

Press <Skip Error>, and continue printing. However, pages that include the data that caused the error may not be printed correctly.

PDL DLG Mem. Alloc. Err

The printer stopped operating normally due to an unknown problem.

Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.

PDL GL Orig. Pt Unknown

The printer stopped operating normally due to an unknown problem.

Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.

PDL GL Coord.Result

The printer stopped operating normally due to an unknown problem.

Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.

PDL Invalid GL Input

The printer stopped operating normally due to an unknown problem.

Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.

PDL GL Range Check

The printer stopped operating normally due to an unknown problem.

Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.

PDL GL Memory Full

The work memory was insufficient when the system was processing data (in particular, graphic processing and text processing).

Press <Skip Error>, and continue printing. However, pages that include the data that caused the error may not be printed correctly.

PDL GL Mem. Alloc. Err

The printer stopped operating normally due to an unknown problem.

Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.

PDL IMG Refer. Data Err

The TIFF or JPEG data includes data that cannot be processed with the machine.

PDL IMG Initial. Err

The memory for printing the TIFF or JPEG data was insufficient.

PDL IMG Process. Error

An unknown problem occurred while processing the TIFF or JPEG data.

Cancel printing, initialize the printer, and try printing again. However, note that initializing the printer will erase all the data in the memory of the machine. Custom Settings

PDL IMG Invalid Data

The TIFF or JPEG data includes data that cannot be processed with the machine.

Cancel printing, and check the TIFF or JPEG data.

Press <Skip Error>, and continue printing. However, the data that caused the error will not be printed.

Data that cannot be processed by the machine because the machine has the same IP address as another device, etc. was sent.

Cancel printing, check the IP address in <TCP/IP Settings>, and change the IP address if necessary.

PDL IMG Work Memory Full

The memory for processing the TIFF or JPEG data was insufficient.

Press <Skip Error>, and continue printing. However, the data that caused the error will not be printed.

PDL nn Rendering Error (nn is the module name)

The printer stopped operating normally due to an unknown problem.

Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.

PDL PDF Error

PDF data that cannot be processed with the machine was sent.

Cancel printing, optimize the PDF using Adobe Acrobat, and try printing again.

Cancel printing, open the PDF file in an application, and try printing again using the printer driver.

If the above-mentioned remedies do not solve the problem, make a note of the message and contact your dealer or service representative.

PDL PDF Data Decode Err

The password for printing the PDF file is incorrect.

Enter the correct password, and try printing again.

Printing is not allowed in the security settings of the PDF file.

Change the PDF file to allow printing in an application for editing PDF files.

If the PDF file is linked with a policy server, the policy server cannot be accessed.

Check whether the policy server is turned on.

Check whether the machine, policy server, and network are operating normally.

PDL PDF Memory Full

There is insufficient memory to process the PDF data.

Cancel printing, optimize the PDF by adjusting settings such as the image resolution using Adobe Acrobat (to reduce the size of the data to print at one time), and perform printing again.

Cancel printing, divide the pages of the PDF data in Adobe Acrobat into multiple files, and try printing again.

Cancel printing, open the PDF file in an application, and try printing again using the printer driver.

PDL RIP Process. Error

The printer stopped operating normally due to an unknown problem.

Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.

PDL XPS Error

An undefined error occurred.

Restart the machine and try again. If the message is still displayed, make a note of the message and contact your dealer or service representative.

PDL XPS Initialize Error

An unknown error such as not being able to retrieve memory during initialization occurred.

Restart the machine and try again. If the message is still displayed, make a note of the message and contact your dealer or service representative.

PDL XPS Rendering Error

An error occurred in the rendering system.

Restart the machine and try again. If the message is still displayed, make a note of the message and contact your dealer or service representative.

PDL Image Comp. Error

The printer stopped operating normally due to an unknown problem.

Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.

PDL Rendering Timeout

The printer stopped operating normally due to an unknown problem.

Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.

PDL Data Transfer Error

The printer stopped operating normally due to an unknown problem.

Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.

PDL Reg. Access Error

The printer stopped operating normally due to an unknown problem.

Restart the machine. If the message is still displayed after restarting the machine, make a note of the message and contact your dealer or service representative.

Cannot recall the button settings because other operations are being performed.

The <Personal>/<Shared> cannot be called when another function is being executed.

Call the <Personal>/<Shared> after the operations for the other function are complete.

Register to Home will be canceled and you will be returned to the function screen because you do not have permission to register buttons. Log in as an administrator, then try again.

Registering personal buttons/shared buttons is restricted in user authentication.

Check the following settings.

Customizing the <Home> Screen

Load staples into the stapler unit.

There are no staples in the staple case in the finisher's stapler unit.

Replenish the staples (replace the staple case).
Maintenance

The password does not meet the policy requirements. Change the password.

The entered password violates the password policy.

Enter a password that complies with the password policy. If you do not know the password policy, consult your system administrator.

Timer settings for this device and the authentication server may not be synchronized. Contact the system manager.

The date and time settings of the machine and the authentication server are different.

Synchronize the date and time settings of the machine and the authentication server.

The amount of data stored for registered users has reached the limit. You can perform operations, but no data (job setting logs, personal settings content, etc.) can be stored this time. To be able to store data from the next time you log in, unnecessary data must be deleted from other users. Contact the system manager or refer to the manual for details.

The user setting information could not be saved because the maximum number of users who can be registered was exceeded.

To save new user setting information, delete any unnecessary user setting information.
Deleting User Setting Information

If you are not using the Personalization function, delete user setting information, and then set <Enable Use of Personal Settings> (<Enable Use of Personal Settings>) to <Off>.

You can specify settings to automatically delete old user setting information if the number of users who can be registered is exceeded.
<Action When Maximum Number of Users Exceeded>

Register to Home will be canceled because you are not logged in. Return to the function screen, log in, then try again.

Registering shared buttons is restricted in user authentication.

Load paper.

The paper in the paper source has run out.

Load paper in the paper source displayed on the touch panel display.
Loading Paper

The paper guides in the paper source are in the wrong position.

Adjust the paper guides according to the edges of the paper. Depending on the cut edge of the paper, multiple sheets of paper may be fed together when printing, which can cause paper jams. This can be reduced by changing the orientation of the loaded paper.

The paper settings differ from the paper that is loaded.

Check the paper settings in <Consumables/Others> in

(Status Monitor). If the paper settings are incorrect, match them with the paper that is loaded. Paper settings can be specified for all the paper sizes and types set in the paper drawers in

(Settings/Registration)

<Paper Settings>.

The paper settings of the driver or application differ from the paper that is loaded.

Check the paper settings on the [Printing Preferences] screen of the printer driver, and if the paper settings are incorrect, match them with the paper that is loaded.

Some applications require license confirmation.

The license file of a MEAP application will expire soon.

Add a license file.

Cooling... Wait a moment.

Cooling is being performed since the main unit's internal temperature has risen above the predetermined level.

Wait a moment.

Information set by the currently logged-in user will not be stored.

The user setting information cannot be saved because the maximum number of users who can be registered was exceeded.

To save new user setting information, delete any unnecessary user setting information.
Deleting User Setting Information

You can specify settings to automatically delete old user setting information if the number of users who can be registered is exceeded.
<Action When Maximum Number of Users Exceeded>

Login failed. Anonymous access to the authentication server is not allowed. Contact the system manager.

Anonymous access is not allowed in the LDAP server.

Select the check box in [Use authentication information] on the screen for entering information on the LDAP server, and set the user name and password according to the information registered in the LDAP server.
Registering Server Information

Login failed. The account information necessary to log in to the authentication server is invalid. Contact the system manager.

The user name or password is not set correctly.

On the screen for entering the information for the LDAP server, set the correct settings according to the settings registered in the LDAP server.
Registering Server Information

Cannot log in. Check the login destination.

The login destination information entered on the mobile device side is incorrect.

Confirm that you have specified the correct login destination, and then log in again.

Cannot store the password because the number of passwords stored for each user has reached the limit.

The login user password cannot be registered because the maximum number of passwords has been exceeded.

Delete unnecessary password information.

If a six-digit number is displayed when you are logging in

If an error occurs when you are logging in, a six-digit number may be displayed below the message. Take the necessary measure depending on the six-digit number displayed.

310001

Communication with the authentication server failed.

Check the network cables from the machine and the domain controller (Active Directory).

Check whether the domain controller is down.

Check whether name resolution is working correctly with the DNS server set for the machine on the domain controller.

Try again after augmenting the current value of [Period Until Timeout:] in the Active Directory settings.

310002

When [Use access mode within sites] is enabled on the machine, the site information of Active Directory is not set correctly.

Check whether the site setting on Active Directory is valid.

310003

The network environment is not yet ready.

Check again after a while.

Check whether name resolution to the specified domain name is working correctly (the address can be identified) with the DNS server set for the machine, and then make adjustments as necessary.

The DNS server set for the machine cannot be found, or it is currently unable to communicate. Check the configuration and the communication environment.

322000

A server error has occurred during Kerberos authentication.

In Active Directory, clear the check box for [Do not require Kerberos preauthentication], which is an account option for the logged-in user account. Alternatively, check whether Active Directory is used properly.

322006

The objective user does not exist on the authentication server.

Check whether the authentication user or search user exists on the domain controller to authenticate.

322012

In Active Directory, the check box for [Smart card is required for interactive logon], which is an account option for the logged-in user account, is selected.

In Active Directory, clear the check box for [Smart card is required for interactive logon], which is an account option for the logged-in user account. After clearing the check box, be sure to reset the password. When resetting the password, you can use the same password instead of a new one.

322014

The password or the encryption method for Kerberos authentication is not set correctly.

Reset the password for the authentication user or search user. For more information, see Cannot log in to Active Directory..

Check whether the encryption method for Kerberos authentication is set to a method (AES128-bit encryption and DES) supported by User Authentication.

322018

The validity period of the account has expired.

Check the validity period of the account in question.

322023

The validity period of the password has expired.

Change the password.

In Active Directory, check the setting of the account options for the logged-in user account.

322024

The user name or password is wrong when keyboard authentication is performed.

Check the password of the authentication user or search user.

322029

The attempt to communicate with the writable domain controller failed.

Check the network cable from the writable domain controller.

Check whether the writable domain controller is down.

Check whether name resolution is working correctly with the DNS server on the writable domain controller.

Try again after augmenting the current value of [Period Until Timeout:] in the Active Directory settings.

322037

The date and time settings are not identical between the machine and the authentication server.

Ensure that the date and time settings are identical between the machine and the authentication server.

322xxx

A Kerberos authentication error.

A Kerberos error code is displayed in place of xxx.

323000

An error has occurred during LDAP server authentication.

Check whether Active Directory or LDAP service is used properly.

323008

An LDAP server authentication error has occurred in relation to TLS/non-TLS communication.

Check the communication settings (TLS/non-TLS) of the server.

Check whether the communication settings on the device side are identical to those on the server side.

323048

You are attempting to log in as an anonymous user for LDAP server authentication.

Check whether the LDAP service setting permits anonymous user authentication.

323049/323053

The user information for LDAP server authentication is not set correctly.

Check the user name and password of the authentication user or search user.

Check whether the authentication user or search user is invalid, whether their validity period has expired, and whether they are account-locked.

323xxx

An LDAP server authentication (LDAPBind) error.

An LDAPBind error code is displayed in place of xxx.

324000

An error has occurred during LDAP server search.

Check whether Active Directory or LDAP service is used properly.

324xxx

LDAP server search (LDAPSearch) error.

An LDAPSearch error code is displayed in place of xxx.

325000

An error has occurred during LDAP server authentication.

Check whether Active Directory or LDAP service is used properly.

325010

You have attempted to perform registration to a read-only domain controller.

If the domain controller configured in Active Directory is of the read-only type, no user information editing functions (registering/deleting cards, changing PIN) are available. To use the user information registration function, configure a writable domain controller.

325050

The search user set in the Administrator settings page does not have update authority (write access).

Check whether the search user is granted write access to the user attribute that you are going to modify.

325067

You are attempting to modify an attribute of a Relative Distinguished Name (RDN) such as cn attribute.

You are attempting to modify an attribute of a Relative Distinguished Name (RDN) such as cn attribute. The information of such attribute cannot be modified, so specify another attribute.

325xxx

An LDAP server update error.

An LDAPModify error code is displayed in place of xxx.

331000

User authentication failed.

Check the user name and password. If the user name and password are correct, contact your system manager.

331001

The user name has not been entered.

Enter the user name.

331002

Cannot find the user.

Check the user name and password. If the user name and password are correct, contact your system manager. The user may not exist on the LDAP server, or the search user may not have read access to attribute information of the relevant account.

331003

You are using a card that is not registered on the authentication server.

Check whether you are using a valid card.

331004

Card information is double registered on the authentication server.

Contact your system manager.

331005

The validity period of the logged-in user has expired.

Contact your system manager.

331006

The validity value of the card and that on the authentication server are different from each other.

Check whether you are using a valid card. If you are using a valid card, contact your system manager.

331007

A validity value outside the range is set on the authentication server.

Check whether the server is operated with the correct attribute of validity value.

331008

The account of the logged-in user is locked out.

Contact your system manager.

331009

The user ID of the account you are using to log in to the machine is invalid. Or the Active Directory settings may not be correct.

Check whether all of the required attributes are set correctly.

In Active Directory, clear the check box for [Do not require Kerberos preauthentication], which is an account option for the logged-in user account.

331010

To perform authentication for a specific function, you have attempted to log in as a user who is not permitted to use that function.

Contact your system manager.

331011

Check which functions the logged-in user is able to use.

331012

The PIN of the logged-in user is invalid.

Enter the PIN again.

331013

The account of the logged-in user is invalid.

Contact your system manager.

332000

User information updating failed.

Updating the user information failed. Check whether the user information you used for updating is valid and whether invalid information is not specified for updating.

332001

Already registered card information.

The card of the logged-in user is already registered. Check whether you are using a valid card. Or contact your system manager.

332002

An invalid attribute was specified for user information updating.

When card information editing functions are used, it is not permitted to make registration with sAMAccountName or userPrincipalName attribute in the Active Directory settings. One solution is to use other attribute.

332003

An invalid login name was specified for user information updating.

It is not permitted to register the name of the logged-in user (login name). Check the user name and contact your system manager.

332004

An invalid display name was specified for user information updating.

It is not permitted to register the display name of the logged-in user. Check the display name attribute value on the server being referred to, and contact your system manager.

332005

An invalid domain name was specified for user information updating.

It is not permitted to register the domain name for the logged-in user. Check the domain name you have selected and contact your system manager.

332006

An invalid email address was specified for user information updating.

It is not permitted to register the email address of the logged-in user. Check the email address attribute value on the server being referred to, and contact your system manager.

332007

An invalid role was specified for user information updating.

Check the attribute value for determining the privileges on the side of the server being referred to, and contact your system manager.

332008

The maximum registerable number of users was exceeded during user information updating.

Contact your system manager.