Black and white printing is disabled in the Department ID Management.
To print in black and white, log in using a Department ID for which black and white printing is not restricted. Contact your Administrator for the Department ID and PIN. Setting the Department ID Management
A toner cartridge may not be installed correctly or may be faulty.
Re-install the toner cartridge. If re-installing the toner cartridge fails to clear the error message, the toner cartridge may be faulty. Contact the store where you purchased the toner cartridge or consult the Canon Customer Help Center. Replacing the Toner Cartridge
The toner cartridge used may not be a genuine Canon product.
Only genuine Canon toner cartridges should be used as replacement toner cartridges. Consumables
A toner cartridge may not be installed correctly or may be faulty.
Re-install the toner cartridge. If re-installing the toner cartridge fails to clear the error message, the toner cartridge may be faulty. Contact the store where you purchased the toner cartridge or consult the Canon Customer Help Center. Replacing the Toner Cartridge
The installed toner cartridge may be one with which print quality cannot be guaranteed.
Color printing is disabled in the Department ID Management.
To print in color, log in using a Department ID for which color printing is not restricted. Contact your Administrator for the Department ID and PIN. Setting the Department ID Management
An error occurred when connecting in Access Point Mode.
Set the IP address to other than "192.168.22.xx" in <Config. IP Address For Direct Conn.>. If you still cannot connect, check the subnet mask settings. For details, contact your Network Administrator. <Network>
If the problem persists even after checking the network key, check whether the machine is properly installed and ready to connect to the network. Problems with Wireless LAN Connection
The machine attempted to connect to a wireless router or access point to which the maximum number of devices were already connected.
Decrease the number of devices (clients) that are connected to the wireless router or access point. For information on the maximum number of devices that can connect, see the instruction manual for the wireless router or access point, or contact the manufacturer.
A connection failed due to an error while setting wireless LAN connection.
Restart the machine and set again.
If the problem persists even after restarting the machine, check whether the machine is properly installed and ready to connect to the network. Problems with Wireless LAN Connection
If the problem persists even after checking the wireless LAN connection, check the security settings of the wireless router or access point.
The MAC address of the machine is rejected because the MAC address filter is set at a wireless router or access point.
Set the wireless router or access point to permit the MAC address of the machine and your computer. For more information about how to set, see the instruction manual for the wireless router or access point, or contact the manufacturer. To check the MAC address of the machine, select <Menu> <Preferences> <Network> <Wireless LAN Settings> <Connection Settings> <Connection Information>. Viewing Network Settings
The authentication method of the machine is set to <Shared Key>, but that of the wireless router or access point is set to "Open System."
Change the WEP authentication method to "Shared Key" at the wireless router or access point, and connect again. For more information about how to change, see the instruction manual for the wireless router or access point, or contact the manufacturer.
The network key (the WPA/WPA2-PSK or WEP key) of a wireless router or access point is not entered correctly.
Check the network key (the WPA/WPA2-PSK or WEP key) of the wireless router or access point, and set it to the machine again. For more information about how to check the network key, see the instruction manual for the wireless router or access point, or contact the manufacturer.
Make sure that you have a replacement toner cartridge ready. Replace the toner cartridge if you see this message before you start to print a large job.
NOTE
When selecting <Continue Printing>
When printing, you can continue printing the original.
If this message is displayed for the black toner cartridge while an I-Fax document is being received, the machine does not perform printing so that unclear print is avoided. To continue printing even if the amount remaining in toner cartridge is running low, set <Continue Print. When Amount in Cart. Low> to <On>. <Receive>
The memory became full of print data that could not be printed due to errors.
Cancel printing of documents to which an error has occurred, or print the documents by selecting <Skip Error> on the screen for checking the printing status. Canceling Prints
If you print received documents on paper other than A4 or Letter size, some portions of the image may be missing or the image may be divided and printed onto several sheets.
Make sure that you have a replacement toner cartridge ready. Replace the toner cartridge if you see this message before you start to print a large job. Consumables
NOTE
When printing, you can continue printing.
If this message is displayed while an I-Fax document is being received, the machine does not perform printing so that unclear print will be avoided. To continue printing even if the amount remaining in toner cartridge is running low, set <Continue Print. When Amount in Cart. Low> to <On>. <Receive>
Make sure that you have a replacement toner cartridge ready. Replace the toner cartridge if you see this message before you start to print a large job. Consumables
Make sure that you have a replacement toner cartridge ready. Replace the toner cartridge if you see this message before you start to print a large job. Consumables
Make sure that you have a replacement toner cartridge ready. Replace the toner cartridge if you see this message before you start to print a large job. Consumables
Printing is disabled in the Department ID Management.
Log in with a Department ID for which printing is not disabled. For the Department ID and PIN, contact your Administrator. Setting the Department ID Management
Change the WEP authentication method to "Shared Key" at the wireless router or access point, and connect again. For more information about how to change, see the instruction manual for the wireless router or access point, or contact the manufacturer.
This site uses cookies to provide its contents and functions and improve their qualities etc. You can find out more about our use of the cookies here. If you select "Reject", only cookies necessary to provide the contents and functions of the site are recorded and stored.